Interior

These are often cracked or collapsed causing your seats to lean back too far. One kit does one seat, two kits required per car.*NOTE* Don't discard your original screws! The screws supplied with this kit have a head that is just slightly smaller than original so when you really tighten the screws down the head goes right on through the stop! A very small washer will cure the problem if you choose to use the screws supplied. Replaces Ford Parts #: C8ZZ-6560310 & C8ZZ-6560311

Bucket seat track set for all 1971-73 Mercury Cougar and Ford Mustang. New manufactured, this is a product of Taiwan. One set is enough to do one seat, mounting hardware is sold separate. Kit includes D1ZZ-6561704-A, D1ZZ-6561705-A, and C5ZZ-6561726-A. Limited supply.*Note - Not compatible with the power seat option.

D1ZZ-6561828-A Good used replacement spring for the bucket seat tracks on all 1971-73 Mercury Cougar and Ford Mustang Bucket seat sliders. This is the spring on the lever side.

D1ZZ-6561883-A Spring that keeps tension on the adjusting seat track latch, it keeps it locked. 1971 Mercury Cougar and Ford Mustang Bucket Seats.

Good used lever side track for all 1971-73 Mercury Cougar and Ford Mustang. These have been carefully inspected for cracks and bends. Will need to be repainted. Ford master part number D1ZZ-6561704-A.*Note - Not compatible with the power seat option.

Good used non-lever side track for all 71 - 73 Cougar and Mustangs. These have been carefully inspected for cracks and bends. Will need to be repainted. Ford master part number D2ZZ-6561705-A.*Note - Not compatible with the power seat option.

3/8-16X1-1/8 Grade 5 flange bolt for attaching bucket seat tracks in any 1971-73 Mercury Cougar or Ford Mustang. Sold individually, 4 needed for each seat. Replaces Ford part number 56340-S2.

1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. These are used, and because of the low grade of chrome plating, these will show some form of light pitting.  handle, which is larger and has a faux leather covered handle in a variety of colors. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Tired of picking your broken button off the floor? This inserts in the left hand side of your deluxe (colored keyed) shift handle. Quality part made in China, please consider our good used units at half the price! 67 is actually a little different in contour but this will fit fine. Replaces Ford #: C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Black plastic selector button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-M and C5ZZ-7C488-D. Your buttons may have faded to gray after many years. These black buttons are injection molded plastic and have steel wear plates just like the originals. Technically this is a copy of the...

Black plastic selector button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had faux leather wrapping. Additionally it does not fit with the 1973 chromed T-handle without trimming.  Ford part C8ZZ-7C488-B.  Check out our video on rebuilding your shifter below: ...

Black plastic selector button for all 1973 Mercury Cougar and Ford Mustang with automatic transmission. It does not fit with the 1968-72 chromed T-handle.  Check out our video on rebuilding your shifter below: ...

Black plastic dummy button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is the non-moving button on the right side of your shifter handle. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had faux leather wrapping. Ford part C8ZZ-7C488-A.

This arm is attached to your automatic transmission floor shifter (see picture at left). Fits all 1969-70 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for FMX and C-6 transmissions. Ford part number C9ZZ-7302-A. This part may have the course threads or fine threads. Normally this item ships with the course threads. We also stock the 1971-73 version that has a captured stud for...

This arm is attached to your automatic transmission floor shifter. Fits all 1969-73 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. This used part will come with a captured lower stud for attaching the shift rod as shown. Correct for FMX and C-6 transmissions. This version is found on 1972-73 cars, it has the captured lower stud for mounting the automatic shift rod to the transmission. Ford part number D1ZZ-7302-A. Check out our video on rebuilding...

Automatic shifter dial black background. This part screws to the shifter bucket, and sits under the pointer when everything is assembled in your shifter bucket assembly. Fits all 1969-73 Mercury Cougar and Ford Mustangs with automatic transmissions. Original Ford part number C9ZZ-7A213-A also can be D1ZZ-7A213-A. Check out our video on rebuilding your shifter below: ...

Restored shifter T handle as found starting in 1968 and through, 1972 Mercury Cougar and Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little thicker in the body, compared to earlier designs. Core charge applies. Replaces Ford part number C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Used to block light from escaping around shifter stem seal. Fits 1969-73 Mercury Cougar and Ford Mustang as well as 1971+ Pinto, Bobcat, Maverick, and Comet with floor shift automatic transmissions. The 90 degree notched portion straddles the set screw on the cast light housing. Most shifters (almost all) we see do not have this part in place any longer. Ford part number C9ZZ-7E130-A.Note: This fits perfectly on the shifters we have tried, but several customers have commented that it was too...

Reproduction of the little plastic shift indicator arrow, that is illuminated by the little bulb in your shifter housing. Fits 1969-73 Mercury Cougar and Ford Mustang. Also fits 1971 and newer Pinto, Bobcat, Maverick and Comet with floor shift automatic transmissions. Ford part number C9ZZ-7A110-A. Check out our video on rebuilding your shifter below: ...

This fragile little plastic arrow is illuminated by the little bulb in your shifter housing. Fits 1969-73 Mercury Cougar and Ford Mustang. Also fits 1971 and newer Pinto, Bobcat, Maverick and Comet with floor shift automatic transmissions. Ford part number C9ZZ-7A110-A. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for some 1970 Mercury Cougar or Ford Mustang, and all 1971-73 Cougar and Mustangs, with or without consoles. Sometime in the 1970 era, Ford switched to a larger pawl. Easy to identify if you look at the slit on the lever. We sell these bare for those car owners that have pitted shifter levers. Ford part number C9ZZ-7210-C. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the late version with wider width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-C. *Note - Chromed lever internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the early version with small width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-A. *Note - Chromed lever and internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Automatic shifter cable with slot on the threaded end for all 1969-73 Mercury Cougar and Ford Mustangs. Will also work on 1967-68 but features a slot at bottom so as to remove or adjust easily. The 1967-68 version did not have this slot. Ford part number C9ZZ-7D246-A with the slotted threaded stud on the end. Also fits 1971+ Maverick & Comet with automatic floor shifters. Restoration Hint - We suggest purchasing this upgraded cable for use in 1967-68 shifter levers. Much easier to install, and...

MSRP: $62.50 This exact reproduction of the shifter bezel / indicator assembly that is front and center in your interior. The originals almost always started to look poor after a few decades. The 1969 - 1970 version of this shifter cover is a very nice upgrade for 1971 - 1973 owners. Replaces Ford part # D1ZZ-7D443-A Check out our video on rebuilding your shifter below: ...

Leather manual shift boot for the Classic Console Cruiser Console that we offer. Check out our video on rebuilding your shifter below: ...

Bare automatic shifter bucket or housing. Fits all 71 -73 Mercury Cougar and Ford Mustangs with or without console. Also fits 1971+ Maverick and Comet with automatic floor shifters. If one runs with really worn shifter bushings for too long the hole in the side that the shifter arm passes through may be worn beyond tolerances. Ford part number D1ZZ-7A306-A. We inspect the shift detentes and the hole where the bushings go for wear. This bucket is different than the 1969-70 version as shown on...

If your automatic floor shifter has play in it left to right then this is the culprit. Easy to install, (more difficult if you have a 67-68 with center console) these are made from a wear resistant plastic that is better than original. Sold as a pair as two are required per car. This bushing was used in all Ford products equipped with a floor shift automatic from the 1965 Mustang to the late 70's Pinto. Replaces Ford Part # C5ZZ-7A133-A Check out our video on rebuilding your shifter below: ...

Rechromed 1967 deluxe shifter button. Unique to the deluxe faux leather wrapped T handle shifter starting in 1967. One year only design, this one has a convex button for you thumb. Starting in 1968 the button was more rounded to comply with the added safety features mandated in 1968. Core deposit is required, fully refundable with returned 1967 deluxe button. Ford part number C7ZZ-7C488-B. Check out our video on rebuilding your shifter below: ...

This group of parts mounts to the top of the AT shifter arm and rides against the thumb activated button on your T shift handle. Its function is to lift the cable that runs through the chrome shifter stem to lock and unlock the shifter out of Park. The Ford technical name for this part is 'Roller - Shift Lever Lock'. We carefully inspect each part to make sure it is in perfect used condition. Ford part number C5ZZ-7D328-A. Check out our video on rebuilding your shifter below: ...

Exact reproduction for the 1969 - 1973. Perfect fit and finish. You may want to replace yours with this inexpensive unit just for the fresh new luster alone. Your plastic end buttons may have faded to gray but they were originally black like this one. Replaces Ford Part #: C8OZ-7213-A, C90Z-7213-B, D3OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Not a very good color match for Cougar owners, but will work well with blue interiors.Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Allen head set screw for all stock Ford automatic shifter handles on any 1967-73 Mercury Cougar or Ford including Mustang. Uses the same 3/32 inch allen wrench for attaching as the originals. Most handles take two of these set screws, one on the dummy button, and one to attach to the top of the shifter lever. The 1973 all chrome shift handle only uses one of these set screws. Original Ford part number 374985-S. Check out our video on rebuilding your shifter below: ...

Reproduction automatic shifter lever in chrome for the Mercury Cougar or Ford Mustang. Comes with inside cable parts. See the related items for more of your shifter needs. Check out our video on rebuilding your shifter below: ...

Very nice chrome on this used shifter lever for automatic transmissions. Can fit all 1969-73 Mercury Cougar and Ford Mustangs with FMX or C-6 automatic transmissions. We have found that there is an early and a late version of these levers. The early versions used the C5ZZ-7C442-A pawl. The easiest way to determine which is early or late is the width of the slot at the bottom of the lever. If one nickel fits into the slot, it is early. Two nickels will easily fit into the later slot. Bare...

Very nice chrome on this used shifter lever for automatic transmissions. Can fit all 1969-73 Mercury Cougar and Ford Mustangs with FMX or C-6 automatic transmissions. We have found that there is an early and a late version of these levers. The late versions used the C9ZZ-7C442-A pawl. The easiest way to determine which is early or late is the width of the slot at the bottom of the lever. If one nickel fits into the slot, it is early. Two nickels will easily fit into the later slot. Bare...

Automatic shifter arm pawl - late version. Mounts inside the bottom of the shifter arm in the slot with the cable and spring. Fits original chromed shifter levers or arms 1970-73 Mercury Cougar and Ford Mustang. The early pawl has a key with a thickness of 0.100", the later (1970ish-73) with a thickness of 0.159". Check your shift lever for the size that you need. Ford part number D0ZZ-7C442-A. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the "Select-Shift" automatic transmission. FMX transmissions only, code "X" on your door data plate tag. Most 351-2V engines received the FMX automatic transmission. Rod originally had a "Yellow" paint daub for identification purposes on the Dearborn assembly line. Shift rod approximately 18-1/2 inches long. Rod stamped D1ZA-7340-AA. Check out our video on rebuilding your shifter below: ...

This never came on a Cougar, but it is a nice upgrade from the string that attaches your seat belt shoulder strap to the coat hanger when the shoulder strap is not in use. Fits all models except convertible. Originally, the shoulder strap connected to the bolt cover on one end, And to a string on the shoulder strap that connects it to the coat hook to keep it out of the way when not in use. This new hook slides into the track on the back of the moulding over the door, and is used instead of...

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

This is the exact same cut of sound deadener as the tar based sound deadener, but cut out of the foil heat shield rather than the paper backed tar. The foil heat shield weighs over 20 Lbs less than the paper backed tar when cut into the same pattern. This makes shipping this over seas much more affordable than the paper backed tar version of the underlayment kit.For a super cheap version of this insulation, try this item: foil insulation ...

5/16" thick sound deadening and heat reflecting material, comes in a 4' X 6' sheet that can be cut to fit. This insulation consists of two layers of polyethylene bubble film sandwiched between two layers of aluminum foil. Temperature range rated -60 deg. F. to 180 deg. F. Combining this with the tar-based sound deadener underlayment will result in similar sound deadening as the OEM sound deadener.Below is listed how many rolls you will need to underlay the sections of a Cougar:  Area...

Reproduction 7 Piece sound deadener underlay for the the 71 - 73 Convertible Cougar.

Reproduction 5 piece sound deadener underlay for the 71 - 73 Cougar Coupe

This is the same kit everyone else is offering, but if what you are looking for is a kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least this listing will give...

This is the same sound deadener kit that everyone else is offering, but if what you are looking for is a kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least...

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...