Headlight Switches

Headlight relay kit converts the 1967-68 Mercury Cougars with quad or 4 headlights to modern car technology (kit also works on 1967-68 Mustang 2 headlight systems). If your Cougar suffers from dim headlights you are not getting a full battery power to the back of your headlamp bulbs. Safe for use on our vintage cars. Still uses your headlight switch. Instead of carrying reduced voltage to the headlights through the switch, the switch triggers the relay, which takes power directly from the...

Headlight relay kit converts the 1967-68 Mercury Cougars with quad or 4 headlights to modern car technology (kit also works on 67-68 Mustangs 2 headlight system). If your Cougar suffers from dim headlights you are not getting a full battery power to the back of your headlamp bulbs. Safe for use on our vintage cats. Still uses your headlight switch. Instead of carrying reduced voltage to the headlights through the switch, the switch triggers the relay, which takes power directly from the...

Reproduction headlight switch knob for the 71 - 73 Cougar.

There is not a special part number for this mounting bracket that was originally spot welded to the front of the headlamp switch. We offer these for use with our reproduction headlamp switch. This adapter or retainer is needed to correctly keep the headlamp switch at the correct angle to the lower metal dash. 1967-68 Mercury Cougar.

There is not a special part number for this angled cup that was originally spot welded to the front of the headlamp switch. We offer these for use with our reproduction headlamp switch. This adapter or retainer is needed to correctly keep the headlamp switch at the correct angle to the lower metal dash. 1969-70 Mercury Cougar.

This plastic plate / bracket is installed between dimmer switch and the floor of your 67 - 73 Cougar to provide a bit or protection for the wiring.

This is a tested original FoMoCo headlight switch that will work, there is no warranty. Used headlight switch for four headlight bulb systems and without vacuum headlight covers. Comes as shown, for 1967-68 Cougar applications you will need the headlight mounting bracket.Replaces Ford part # D2AB-11654, D3AB-11654, C5AB-11654

Unlike the 1968 Cougar headlight switch, the 1967 and 1971-73 version does not have the three vacuum ports connected to it. Don't be fooled . . . Most vendors will sell you a Mustang switch and tell you it is the same. Visually it may look the same but internally it has a circuit breaker designed for a two headlight system, the Cougar has four headlights. If you only use the low beams you would be fine but if you have all four lights on you will soon experience a blackout. If your original...

This is a tested original FoMoCo headlight switch that will work, there is no warranty. Used headlight switch for four headlight bulb systems and without vacuum headlight covers. Comes as shown, for 1967-68 Cougar applications you will need the headlight mounting bracket.Replaces Ford part # D2AB-11654, D3AB-11654, C5AB-11654

Used headlight switch for the Mercury Cougar. This original FoMoCo unit was tested and will hold 13 pounds of vacuum. The spacer (which is specific to 1969) is not included with this unit, but you can get it right here. Ford part # C9WB-11652-B.

This is a tested original FoMoCo headlight switch that will work, there is no warranty. The primary reason we list these old used switches is that some people are missing their switch altogether and need the beveled cup shaped spacer that mates to the dash. As pointed out in our listing for the reproduction headlight switch, the spacer is not included with our new units. Ford part # D0WB-11652.

Quality "STANDARD" brand reproduction switch for your vacuum actuated hideaway headlights. This switch fits multiple years and makes which means multiple dash configurations. You will need to "break off" your unique extension and attach it to this unit. The extension (spacer) can be removed easily by placing your old switch in a vise and using a wedge shaped chisel to break the tiny spot welds. When reattaching, most any glue such as Gorilla glue, JB weld or even silicone will work as you are...

NOS new old stock headlight dimmer switch. This is a Motorcraft service replacement switch.  Replaces Ford part number C0TZ-13A024-A

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

Used headlight solenoid valve for the vacuum headlight system on the Mercury Cougar and Ford Thunderbird. This functional unit is tested and ready to install.  This is the common version with the separate ground wire where very early 1967 Cougars and Thunderbirds did not have that separate ground wire. We won't always have these used units in working condition in inventory. We also sell a rebuilt solenoid here. Ford part # C7SZ-13A161-A. *NOTE* This item will not ship until a rebuildable...

New Old Stock headlight solenoid valve for the vacuum headlight system on the Mercury Cougar and Ford Thunderbird. This functional unit is tested and ready to install.  This is the early solenoid valve without ground wire. Early 1967 Cougars and Thunderbirds did not have that separate ground wire. Has the proper opaque white color for the vacuum switch plastic.  Ford part # C7SZ-13A161-A.

Used headlight solenoid valve for the vacuum headlight system on the Mercury Cougar and Ford Thunderbird. This functional unit is tested and ready to install.  This is the common version with the separate ground wire where very early 1967 Cougars and Thunderbirds did not have that separate ground wire. We won't always have these used units in working condition in inventory. We also sell a rebuilt solenoid here. Ford part # C7SZ-13A161-A. *NOTE* This item will not ship until a rebuildable...

This is a tested original FoMoCo headlight switch that will work, there is no warranty. Used headlight switch for four headlight bulb systems and without vacuum headlight covers. Comes as shown, for 1967-68 Cougar applications you will need the headlight mounting bracket.Replaces Ford part # D2AB-11654, D3AB-11654, C5AB-11654

NOS, never been installed part they may or may not come with original box, will show shelf wear. Ford Engineering number stamped on the part is C8WB-11652-C.

May or may not come with original box, guaranteed to be never installed NOS. Ford engineering number stamped on part is C9WY-11652-B

Brand new in the Motorcraft box original FoMoCo part. Engineering number stamped in the part is D0WB-11652-B

These original FoMoCo headlight switches have been tested for both vacuum and electrical functionality. These old switches also come with the already attached "C" shaped spacer that mates to the dash. We all know how hard it is to get that spacer glued in on a new switch (which doesn't come with the spacer). Stamped witht the "Motorcraft" trademark and Ford part number C8WB-11652-C.