Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Reproduction course threaded eye bolt for the leaf springs on the 1967 Mercury Cougar or Ford Mustang.Sold individually

Holds insulation to the firewall. Sold individually, 6 per car. Replaces Ford part # C8ZZ-6501691.

Self threading white plastic. Used on front and rear valances.Sold individually.

Reproduction alternator mounting kit for the Mercury Cougar or Ford Mustang equipped with the 390 or 428 engine. Spacer not included, but available.

Fits 1967 and 1968 Standard or XR7

 2 piece fuel line. Kit is for fuel and brake lines under the car. Comes as shown. Quality AMK kit. Fits 1967 Mercury Cougar and Ford Mustang. F-3962

Reproduction brake and fuel line clamp kit for Mercury Cougar and Ford Mustang.

If your fuel line follows the brake line down the transmission tunnel then you have an early model 1967 and this is the right clip set for you!

This quality kit contains everything you need to replace the original hardware for fuel and brake lines on your 1968 Cougar or V8 Mustang. It even includes 3 new bolts for the metal protector plate for the fuel line near the left rear wheel. Most of the mounting locations can be seen below: Click on images to enlarge. ...

All the nuts, bolts, shims and washers needed to mount the bumper brackets to the frame and then the bumper to the bumper brackets. This kit includes foam looking washers to cover the bumper bolt holes.  This is not technically correct.  From the factory the originals would used a gooey tar based sealant that does not harden.

Complete front and rear bumper mounting hardware for the 1969 Mercury Cougar.

Bolts, washers, and spacers kit for installing the rear bumper brackets on any 1969-70 Mercury Cougar or Ford Mustang.

Sold as a Kit as Pictured.

Reproduction Fastener Kit - Deck / Trunk Lid & Hinges for the 1968 Mercury Cougar / 1968 Ford Mustang 

AMK engine fastener kit for 1971 Mercury Cougar and Ford Mustang with J or C code 429 Cobra Jet engines. This kit claims to have 136 pieces. This kit additionally fits 1970-71 Ford Torino and Mercury Cyclone and other variants with 429CJ engine.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake...

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds. 390 and 427-4V engines without exhaust heat risers. That kit would include a studded bolt for the heat shield. See item 41282.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Reproduction fender fastener kit for Mercury Cougar Standard and XR7.

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits Standard and XR7

Fits Standard and XR7 with front bumper guards.

Fits Standard and XR7 Sold as a Kit as Pictured.

New improved set of 6 screw for the glove compartment hinge on all 1967-68 Mercury Cougar and Ford Mustangs. Three 10-24 bolts with 0.72" conical washer heads to go into dash, and three 10-24 bolts with 0.50" conical washer heads to attach to glove box door. This is an updated proper kit for 1967-68 Mercury Cougar and Ford Mustang glove box door hinge. All AMK bolts, but WCCC special recipe. 6 pieces as shown.

Fits standard and XR7 Sold as a Kit as Pictured. Check out this video

Reproduction grille mounting kit for the driver (left hand) and passenger (right hand) sides of the Mercury Cougar.

Reproduction mounting kit for the center grill for the Mercury Cougar. Check out this video

These reproduction hood and hinge bolts and U nuts fir both the Standard and XR7.

This reproduction hood latch and catch screw and U nut kit fits both the Standard and XR7 and is sold as a kit as pictured.

This reproduction hood latch vertical support screw and U nut kit fits both the Standard and XR7 and is s sold as a kit as pictured.

Fits 1967 and 1968 Standard or XR7

This is a Mustang kit and it includes 4 screws, 2 metal nuts, 2 self-threading plastic nuts and 2 anti-rattle bumpers as pictured.For Cougar, you need this kit plus 2 more plastic nuts, found here.

Fits Standard and XR7

Correct Fit and finish for 1967, and works for 1968. Connects the overhead roof console to the mounting bracket. The only difference between the 67 and 68 kits are that the 67 screws are chrome and the 68 are zinc. The zinc will discolor over time, so we suggest using the 67 kit on a 68. Replaces Ford Part #: 519A58

This reproduction quarter panel extension fastener kit fits both the Standard and XR7.

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits 1967 and 1968 Standard or XR7

Fits 1967 Standard and XR7

Fits Standard and XR7

This kit includes all hardware needed for attaching the scoops to the rocker panels on the sport special rocker mouldings. Includes all screws and studs to attach the scoops to the end of the rockers, and to attach everything to the the vehicle.

This kit connects the Overhead Console mounting bracket to the roof. Screw heads and clips differ slightly between 67 and 68. Replaces Ford Part #: 519B24, 519B38, 519B46

This kit connects the Overhead Console mounting bracket to the roof. Screw heads and clips differ slightly between 67 and 68. Replaces Ford Part #: 519B24, 519B38, 519B46

We will make sure these original seat belt bolts are damage free. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! *NOTE* Pictured is a complete set of 1969 Torx bolts, spacers, and washers for a coupe. May also have some minimal surface rust.

Used bolts, and usually new washers. Convertible kit comes with 4 - "A" bolts, 4 "B" bolts, 10 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang convertibles. Coupes or hard tops would include shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us...