Door Parts

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part # C7ZZ-6522800-C.

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: D0ZZ-6522800-A. ...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

Pressure die cast in zinc and heavily chrome plated. Excellent quality. Drive pins and washers included, sold as a pair.

Reproduction driver side (left hand) vent / wing window handle for the Mercury Cougar or Ford Mustang.

Reproduction passenger side (right hand) vent / wing window handle for the Mercury Cougar or Ford Mustang.

This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

This concours correct reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This Daniel Carpenter manufactured unit is made of slightly less dense material than the Midland unit, .75lb as compared to .85lb.We have included a few comparison pictures so that you can make an informed decision. Sold as a pair and includes the metal...

Economy overseas reproduction door perimeter seal. These glue to the perimeter of the doors and are held in by screws on both ends. Sold as a pair. Replaces Ford part #D1ZZ-6520530-A.

Premium reproduction Door Weatherstrip for the 1971 - 1973 Mercury Cougar or Ford Mustang.  These glue to the perimeter of the doors and are held in by screws on both ends.  Sold as a pair. Replaces Ford part #D1ZZ-6520530-A.

Sold as a pair, includes plastic fasteners. There are multiple manufacturers of this particular item and we feel after using them all on our own cars that we carry the best out there. Replaces Ford part #C7ZZ-6520530-A.

This offshore reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This overseas reproduction sold by Daniel Carpenter is simply another option to the US made version, and has been known to fit better than the US made weatherstrips.  Sold as a pair and includes the metal fasteners. Replaces Ford part #...

Correct for Coupe and Convertible, Mustang and Cougar. This vertical weather strip slides into the stainless steel strip that attaches to the back side of your left hand door glass. These cost a couple of dollars more than some you will see but are substantially better fitting than the budget version. Replaces Ford part # C9ZZ-65214A15-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video...

Correct for Coupe and Convertible, Mustang and Cougar. This vertical weather strip slides into the stainless steel strip that attaches to the back side of your right hand door glass. These cost a couple of dollars more than some you will see but are substantially better fitting than the budget version. Replaces Ford part # C9ZZ-65214A14-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video...

Perfect fit, great reproduction. These plastic discs are found on all 69-70 convertibles on the rear of both decor and xr7 interior levels. We are unclear as to all the "exact" applications on all years and models but one application we have verified is the fronts of 1971 - 73 Cougars equipped with standard interior. The reason the standard interior 71-73 Cougars came with these is that the door panels were very thick on the 71-73 decor / XR7 models and quite thin on the standard models and...

This is actually not correct for a 1968 but it is all that is available in reproduction. The 1968 front is actually the same 4 1/4" length as the rear. Many people prefer the longer version as it makes it easier to roll up. We do have good used 1968 front cranks for those who prefer to stay with original. The portion that attaches to the splined shaft on the window regulator protrudes from the back 3/16" (as shown on the left in the comparison picture) and will not clear the 71-73 door panels...

Very correct reproduction with a quality chrome finish. The rear (quarter) window cranks are listed in the interior section. Keep in mind their are multiple makers of this part and this is the best. Replaces Ford part # C5ZZ-6523342-C.

C8AB-7630323-A Usually these will not have knobs. Plan on purchasing new knobs. Ask about our B grade knobs that will have some pitting or lusting issues. This is the correct "shorty" crank for a 1968 Cougar front window crank. It is the same length as the rear 1968 - 1970 but uses a center screw instead of a side Allen set screw. The 1969 - 1970 crank (with AM or no radio) looks the same but is longer. These shorter cranks were also used in conjunction with the factory door speakers used in...

This handle is a good replacement for the window cranks found on the 1971 - 1972 Cougar both front and back. The originals were 4 1/4" total length and this replacement handle is 4 7/8" long. The important detail on these is the fact that the female portion that attaches to the splined window regulator protrudes from the back 5/16". If you are using our chrome backing plates on your 69 -70, then this is the crank you will need to provide the correct clearance.Used before 10/71,...

Used on both the front and rear of the 1971-1972 Mercury Cougar produced before 10/1/71. The picture above shows the difference between the early version (right) and the later version (left). Plan on purchasing new knobs to go with the bare crank, we have 7 different colors to choose from. See related items. Inquire about a B grade knob if you are looking for something just so that you have a window crank. Ford Part # D0AZ-7630322-A, casting # as seen on the back D1AB-7630322-AWA. ...

Best quality of the three version made and the only one that comes with the decal installed. This is held on by an Allen set screw, we often get calls from people who cannot figure out how to remove these. Check our good used cranks if you like to keep original FoMoCo parts on your Cougar. Replaces Ford part number C8ZZ-6530322-A.

This is a good used original rear window crank with no obvious scratches or pitting. May or may not come with random colored knob. It most likely will be missing the decal but will have the original set screw. Ford part number is C8ZZ-6530322-A, casting number shown on back is C8ZB-6530323-A. Black knobs are the most commonly ones requested, plan on buying new knobs if you need black.

Reproduction window crank used on front doors of cars produced after 10-1-71 with no factory door speakers. Replaces Ford part number D2AZ-7630322-AOriginals have a casting number of D3AB-6523342-AA.

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part #C8AZ-6223352-GR *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part Number #C8AZ-6223370-ADiameter 1-1/2"

Same harness works for driver or passenger side, sold individually.

Used pigtail that runs from the 14401 harness to either the driver or passenger side door harness for the door ajar.

Used pigtail that runs from the main 14401 harness to the driver side door jamb switch.

Used pigtail that runs from the main 14401 harness to the passenger side door jamb switch.

Used under dash wiring harness repair plug and pigtail for the door ajar / seat belt warning for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail lead to the door ajar switch on the Mercury Cougar XR7 or Standard model with the Safety and Convenience option. This is part of the 14401 main under dash wiring harness.

[No Description Provided]

Nice reproduction of the chrome bezel on an XR7-G mirror. Often these become so pitted they cannot easily be restored. This is an exact fit, quality replacement.Click on images to enlarge. ...

This item will have scratches but no cracks or peeling chrome. These original bezels are made from chromed plastic.Ford part number C8SZ-17B733-B

This is the rubber that goes into the bracket of the bottom of the center of the door, for 1970 bolt-in door glass.  Note that this bumper is substantially taller than the 69 version.  See C9ZZ-6521762-A for the 1969 glued-in door glass version. If you are swapping out a door on a 69 or a 70 don't forget that the door glass is different between the years and, if you have to swap out the glass, you will need to make sure you have the correct version of this part for the type of glass...

Used door window stop, cover plate, for any 1969-70 Mercury Cougar and Ford Mustang. These were originally painted body color, and were laid on either inside the front cowl or the package tray for painting. The one for the doors is roughly 25/32" x 3-3/8 inches long, the holes are 5/16, and the spacing is 1-25/32 on center to match the stop. Replaces Ford part number C9ZZ-65234A30-A.

Left side factory stainless steel door guard.

Left side factory aluminum door guard.

Right side factory stainless steel door guard.