Door Parts

Reproduction manually adjustable side view mirror in black for the Mercury Cougar and Ford Galaxie. This ambidextrous mirror works on either the passenger or driver side door and a gasket is included. Replaces Ford part # C7AZ-17696. Dimensions: Base Hole Spacing: 5-7/8" Base Length: 6-5/8" Overall Height: 5-1/8" Mirror Width: 5-1/8" Mirror Height: 3-5/16" Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Reproduction manually adjustable side view mirror in chrome for the Mercury Cougar and Ford Galaxie. This ambidextrous mirror works on either the passenger or driver side door and a gasket is included. Replaces Ford part # C7AZ-17696. Dimensions: Base Hole Spacing: 5-7/8" Base Length: 6-5/8" Overall Height: 5-1/8" Mirror Width: 5-1/8" Mirror Height: 3-5/16" Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Fantastic quality in all respects, concours quality. Don't forget to select a mounting gasket and mounting kit if needed. Replaces Ford part # C7WY-17696-A.*NOTE* Mustang uses a different mirror and will not fit contrary to what you may have seen advertised elsewhere!Hole spacing: 4 3/8" Do you have riv-nut questions? Here are riv-nut answers! ...

Working driver side (left hand) grade "B" remote mirror with dull chrome. Don't have too high of expectation on this, it is 40 years old and comes from a car we most likely pulled from a brier patch...

Unfortunately the wand is broken off from this grade "B" driver side (left hand) mirror. It will require drilling out the old one and epoxy gluing in another or removing the complete controller from another 1970's like mirror. Chrome is dull and often will have light pitting. Ford part # D0WY-17696-A. *NOTE* If you have a blank area where your color code is supposed to be typed on your 1970 door data decal, then you have a "special order" paint color. Because sport mirrors came pre-painted...

New Old Stock driver side (left hand) mirror that has never been installed. Since the wand is recessed into the door panel on the 1969 Cougar, the wand is not prone to breaking off like the 1970 version which protrudes straight out. Ford part number C9WY-17696-A NOTE - Cable length should be 18" from the base of the mirror to the inner end of the remote wand assembly. In order to keep the cable from hitting the window, there's usually a clip to hold it away from the glass. This clip is hard to...

Quality reproduction mirror for your 1967 - 1968 Cougar. Whereas it is not easily detected at first glance, the head of the mirror does have a slightly different contour than original. The base is spot on perfect and the controller, cable assembly are all excellent quality. The 67 style wand is no longer available, so this mirror includes the 68 style ball end wand. Plastic mounting pad and hardware included. *NOTE* Mustang mirrors will not work on a Cougar no matter what "they" told...

Reproduction driver side mirror lens replacement for the 67 - 68 Cougar chrome side mirror. NOTE: The narrow end of the mirror goes up top on Cougar and is reversed for Mustang. These mirrors are manufactured for the Mustang, so the small supplier part number at the bottom will be upside down and on top for Cougar. 

Reproduction manually adjustable convex passenger side view mirror in chrome for the Mercury Cougar or Ford Galaxie.  Gasket and screws included. Replaces Ford part # C7AZ-17696. Dimensions: Base Hole Spacing: 5-7/8" Base Length: 6-5/8" Overall Height: 5-1/8" Mirror Width: 5-1/8" Mirror Height: 3-5/16" Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Finally! A correct looking and fitting quality mirror for the passenger side of your 1967 - 68 Cougar. This is NOT a Mustang part made to "kind of work". For years our customers have called almost weekly asking for the "RARE" 1967-68 right hand outside mirror listed in their owners manual as an option available at their local "Lincoln - Mercury Dealer". The intention may have been to offer one but it actually never came to be... This product has been getting great reviews in the Cougar...

Reproduction convex passenger side mirror lens replacement for the 67 - 68 Cougar chrome side mirror. NOTE: The narrow end of the mirror goes up top on Cougar and is reversed for Mustang. These mirrors are manufactured for the Mustang, so the small supplier part number at the bottom will be upside down and on top for Cougar. 

Reproduction driver side (left hand) remote sport mirror for the Mercury Cougar XR7. This unit will come with a primered base and head so that you can paint it to match the rest of your car. If you have some good used 1970 mirrors for sale with or without the wand intact we would like to hear from you as these are getting very hard to find! 1970 was the first year you could get a factory installed sport mirror on your XR7, Sports Special, or Eliminator. If you would also like to have a...

If your mirror is fine except a broken off wand (control lever) it is an easy fix. Since the wand is made of a soft metal it is not too hard to drill out the old and replace it with one of our threaded replacement units. One can also remove the entire adjuster assembly form another mirror that has a broken base and carefully attach it. If you have some good used 1970 mirrors for sale with or without the wand intact we would like to hear from you as these are getting very hard to find. Have...

Good working used mirror with joystick intact and no cracks in the base. The mounting holes on the base are located 6 3/4" apart. Ford number inside the base D1WB-17743. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Do you have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road? WCCC to the rescue! Check out this video Check out...

This reproduction remotely operated driver side (left hand) mirror is unique to the 1969 XR7 as evidenced by the chrome base. The Eliminator and Sports Special used a painted base, but in late 1969 the XR7 came with a painted base. This reproduction unit will come with the correct chrome base, but the head will be in primer for you to paint to match the color of your killer Cat. The XR7, Sports Special, or Eliminator never came with a passenger side (right hand) mirror from the factory, but...

This driver side (left hand) mirror is unique to the 1969 XR7 as evidenced by the chrome base. The Eliminator and Sports Special used a painted base. Good used mirror with good chrome and a working adjuster. In late 1969 the XR7 came with a painted base. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror. This fits any FoMoCo Sport mirror 69 and up. Comes with two round pieces of double sided tape.  Lens measures 4 3/8 X 2 7/8. Do you have questions about installing the...

Empty shell / head / housing only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror heads found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Most customers find our reproduction unit to be a better value as it comes with the mirror and mounting hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Fits and looks identical to the 1970 mirror base but is slightly taller. The difference in height between the two versions is indiscernible to the naked eye. Very nice product, works well with original mirror heads, save your hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video Check out this video ...

Used passenger side (right hand) sport mirror for the Mercury Cougar Eliminator. The Ford service replacement part number for the complete assembly is DOOZ-17682-D with a casting # on the base that reads D0OB-17713-AW. This is the correct right hand mirror for your 1970 Eliminator. It was available over the Ford counter to be placed on any 1969-70 Cougar but the 1970 Eliminator is the only model that came from the factory with it. Unlike the driver side door there is no factory embossed area...

Reproduction passenger side (right hand) manually adjusted sport mirror for the Mercury Cougar or 1970-1971 Ford Torino / Cobra / Ranchero / Cyclone. Our kit includes everything needed to mount a bullet style sport mirror to the passenger side of your vehicle. This reproduction unit is far more durable than the originals which were cast with a softer metal. The Ford service replacement part number for the original complete assembly was D0OZ-17682-D. The base in...

Reproduction manually operated passenger side (right hand) sport mirror with a chrome base for the Mercury Cougar XR7. The XR7, Sports Special, and Eliminator never came with a passenger side (right hand) mirror from the factory, but we are offering this one to make driving your Cougar a little safer. The use of a chrome base is unique to the early production 1969 XR7, but that changed late in the 1969 production run when Mercury changed to a painted base like the ones used on the Eliminator...

Dimensionally correct reproduction that will allow you to use an original XR7-G remote mirror or the manual mirror found on the Hurst Oldsmobile or AMC Rambler Scrambler. Do you have riv-nut questions? Here are riv-nut answers!

This driver side (left hand) remote mirror was used only on the 1968 XR7-G Cougar and is a direct bolt on for any 1967-68 Cougar and uses the same mirror base gasket. It comes ready to install with the exception of correct adapter base that we sell separate. The casting and chrome are good quality here, the only thing we find issue with is the quality of the mirror lens and the fact that the lens is rather loose in its setting. It does hold its position well as you drive down the road. Do you...

Good used external XR7-G driver side (left hand) rear view mirror with its adapter base, lens, and cables all in good used condition.  Do you have riv-nut questions? Here are riv-nut answers!

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out this video Still have riv-nut questions? Here are riv-nut answers! ...

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

New Old Stock Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Has a white button for the switch as shown. Replaces Ford Part #: C8OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1968 - 1973Mercury Cougar and Ford Mustang. Replaces Ford Part #: C8OZ-13713-A.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option. Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A.

New Old Stock switch for the 1967 Mercury Cougars and Ford Mustangs that came with the 3/4" door jamb switch. This switch will be yellowed from age. Additionally, this switch for the 3/4 inch mounting hole was used on 1965-66 Full sized Ford such as Custom, 500, Galaxie, and XL models, full sized Mercury such as Monterey, S-55, Montclair, and Park Lane. 1965-67 Fairlane, 500, XL, Ranchero, and GT. 1965-67 Mercury Comet, 202, Capri, Caliente, and Cyclone. 1965-67 Ford Mustang, 1965-67 Ford...

Nice reproduction of the 1967 Door Jamb Switch. Replaces Ford Part #: C5AZ-17317-A Please note that most of the plastic bodied, reproduction door jamb switch currently available are for the later model cars and have smaller female plug holes that will not work on a 67.

This is a good used switch for the 1967 Mercury Cougars and Ford Mustangs that came with the 3/4" door jamb switch. This switch will be yellowed from age. Additionally, this switch for the 3/4 inch mounting hole was used on 1965-66 Full sized Ford such as Custom, 500, Galaxie, and XL models, full sized Mercury such as Monterey, S-55, Montclair, and Park Lane. 1965-67 Fairlane, 500, XL, Ranchero, and GT. 1965-67 Mercury Comet, 202, Capri, Caliente, and Cyclone. 1965-67 Ford Mustang, 1965-67...

This switch looks very close to original. On close inspection you will notice that there is no Autolite logo and the plastic is not as milky colored as the originals. Sold Individually. Replaces Ford Part #: C8AZ-13713-C.

C7ZZ-14018-F Left side door ajar switch found on all 1967 Mercury Cougar XR7's and part of the Safety Convenience Package found optionally on Mercury Cougar or Ford Mustang. The safety convenience package or "convenience control" option included 4 warning lights either mounted on the dash (without air conditioning) or on the console. Switch assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 69, C7ZB-10B997-A switch assembly left hand. The engineering number...

C8ZZ-14018 Left side door ajar switch found on all 68 Mercury Cougar XR7's and part of the Safety Convenience Package found optionally on Mercury Cougar or Ford Mustang. The safety convenience package or "convenience control" option included 4 warning lights either mounted on the dash (without air conditioning) or on the console. Switch assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 69, C7ZB-10B997-A switch assembly left hand. The engineering number cast...

C9WY-14018-B Left side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

C7ZZ-14018-E Right side door ajar switch found on all 1967 Mercury Cougar XR7's and part of the Safety Convenience Package found optionally on Mercury Cougar or Ford Mustang. The safety convenience package or "convenience control" option included 4 warning lights either mounted on the dash (without air conditioning) or on the console. Switch assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 69, C7ZB-14018-A switch assembly right hand side. The engineering...

C8WB-14018-B Right side door ajar switch found on all 68 Mercury Cougar XR7's and part of the Safety Convenience Package found optionally on Mercury Cougar or Ford Mustang. The safety convenience package or "convenience control" option included 4 warning lights either mounted on the dash (without air conditioning) or on the console. Switch assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 69, C7ZB-14018-A switch assembly right hand side. The engineering...

C9WY-14018-A Right side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7 Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

D1AZ-14018-A Door ajar switch found on 1971-73 Mercury Cougar XR7's and part of the Convenience Group package found optionally on standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light. Switch is the same for both doors. This switch was also used on 1972 Lincoln MK IV, and 1972 Ford Thunderbird.Fits 71 Cougar and XR7Fits 72 Cougar and XR7Fits 73 Cougar and XR7Fits 72 Lincoln MK IVFits 72 Ford Thunderbird ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. OEM style door jamb switch to release tilt/tilt-away columns on a 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the steering...

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Sold only as a pair. *NOTE* The 1967 uses a smaller pin assembly and this switch will not work without modification. Replaces Ford Part #: C8AZ-13713-C.

Sold individually, two per side, four per car required. These often get destroyed when you go to replace your door window regulator slides. Two of these are used to install the C7ZZ-6523288-A track. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size)Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video...

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: C7ZZ-6522800-C. ...

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part # C7ZZ-6522800-C.