All Products

This is a restored 1973 passenger side taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. ...

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.

Reproduction taillight panel for the 67-68 Cougar. Yet another in a long line of great fitting parts from our friends over at Dynacorn, this replacement taillight panel is perfect for those of you who have rust holes in and around the taillight area. As seen in the photo above, this is only the taillight panel and will not include the quarter extension panels or the rear taillight lower structure. ...

This grade "B" taillight harness is a good used harness that may have one or two professional repairs. Not for use with XR7 or Eliminator models. The difference between XR7 and standard is that the XR7 has a two wire plug to the sending unit and the standard has a single wire.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Used grade "B" taillight wiring harness for the Mercury Cougar. This harness may have one or two professional repairs.This harness is for the Late 1971 (after 5/15/1971) through 1972.  There were 2 other harnesses for early 1971 (D1WY-14405-B before 2/1/71 and D1WY-14405-D from 2/1/71 - 5/15/71).  If you are in need of one of these early harnesses, please contact us so we can discuss what you need.Ford part # D2WY-14405-A.*NOTE* Need help diagnosing a Cougar turn signal...

Used Standard Grade B Taillight Wiring Harness for the 1973 Mercury Cougar 

1968 XR7 and standard Cougars use the same rear wiring harness to the taillights. This is a grade "B" grade harness that may be spliced or repaired. XR7 and Standard Cougars use the same rear wiring harness to the taillights, only the sub-harness that connects to it that runs along the underside of the package tray and down to the fuel sending unit differs XR7 vs. Standard. The major difference is that the xr7 utilizes a two wire plug and the Standard Cougar uses a single wire. Harness begins...

1968 differs in the plugs that connect to the sequential unit. Correct for Cougars built after 1-2-67 with the stop lamp relay located under dash. XR7 and standard Cougars use the same rear wiring harness to the tail lights This is a grade "B" harness that may have minor sun damage, splices or other cosmetic defects. The 1157 taillight bulb sockets are sold separately.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the...

Used grade "A" taillight wiring harness for the Mercury Cougar. No cuts or splices, perfect plugs with no visible corrosion.  This harness is for the Late 1971 (after 5/15/1971) through 1972.  There were 2 other harnesses for early 1971 (D1WY-14405-A before 2/1/71 and D1WY-14405-C from 2/1/71 - 5/15/71).  If you are in need of one of these early harnesses, please contact us so we can discuss what you need.Ford Part Number: D2WY-14405-B. *NOTE* Need help diagnosing a Cougar...

Used XR7 Taillight Wiring Harness for the 1973 Mercury Cougar 

Used grade "B" taillight wiring harness for the Mercury Cougar. This unit may have one or two professional repairs.This harness is for the EARLY 1971 (before 5/15/1971). There were 2 harnesses for early 1971 (D1WY-14405-A before 2/1/71 and D1WY-14405-C from 2/1/71 - 5/15/71).  Ford Part Number: D2WY-14405-B. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

Used grade "B" taillight wiring harness for the Mercury Cougar. This unit may have one or two professional repairs.This harness is for the Late 1971 (after 5/15/1971) through 1972.  There were 2 other harnesses for early 1971 (D1WY-14405-A before 2/1/71 and D1WY-14405-C from 2/1/71 - 5/15/71).  Ford Part Number: D2WY-14405-B. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned...

Three piece Thermactor Smog hose set; moulded, striped, and stamped like original factory installed hoses. The 1968 ink stamped was likely used partially into 1969. We also list hoses with the C9... stamps.Fits: 1968 Ford and Mercury S code 390-4V engines sold in the US.1968 Ford and Mercury W code 427-4V engines sold in the US1968 / 1969 428 Cobra Jet engines. 1968 / 1969 428 Super Cobra Jet engines. ...

This correctly formed carburetor throttle solenoid idle bracket for the 1970 428CJ engines on any Mercury Cougar or Ford Mustang. This is a nice reproduction item.Replaces part # D0ZZ-9B550-A.

Folks, this one just doesn't fit. Probably fits a 1973 or later 302 Ford, but not on the Cougar? The crankshaft center hole is 2-9/16 inches, the originals were just over 2 inches in diameter. Timing Cover not for 1967-1969 289/302/351W using a water pump with a backing plate. Features a cast-in timing pointer and dipstick hole.

Used replacement toggle switch for the 71-73 Cougar XR7. This is a double throw switch that can be used in either the accessory, convertible top or defog positions on the switch assembly.

Used set of 4 toggle switches for the 67 XR7 Cougar dash panel. Included are the toggles for the driver side map light, panel light, passenger map light and courtesy lights. Switches have been tested and may or may not have the tips in place, but we do offer a reproduction set of toggle tips.

Used set of 4 toggle switches for the 68 XR7 Cougar dash panel. Included are the toggles for the driver side map light, panel light, passenger map light and courtesy lights. Switches have been tested and may or may not have the tips in place, but we do offer a reproduction set of toggle tips.

This is a reproduction 3 piece non assembled torque box for the driver side on the 69 - 70 Cougar or Mustang Coupe. The benefit of getting a non assembled torque box is that you'll find installation much easier as compared to the pre-assembled boxes.  Included are inner and outer panels and gusset. Passenger side non-assembled torque boxes are not available.

Rebuilt C4 24 spline torque converter for the 1967 - 68 Mercury Cougar or 1966 - 69 Ford Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core. Ford part number C6AZ-7902-M. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad bearings among other problems. We have a local shop with decades of...

Rebuilt C6 FE Engine torque converter for the 1967 - 70 Mercury Cougar and 1966-70 Ford and Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core. 1966-70 Ford FE engines include: 352, 360, 390, 427, 428, etc. Ford part number C8OZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad...

Rebuilt FMX torque converter for the 1969 - 73 Cougar or Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core.Ford part number C9ZZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad bearings among other problems. We have a local shop with decades of experience do a very thorough rebuild that is...

Outer casing for the C6 transmission on the 71 - 73 Cougar or Mustang. Case only, does not include any of the inner workings or output shaft.

Reproduction transmission cooling lines made of stainless steel for the Mercury Cougar equipped with the FMX automatic transmission and 351 engine. These lines are sold in pairs.

Reproduction transmission cooling lines made of Stainless Steel for the Mercury Cougar equipped with the C-6 automatic transmission and 351 engine. These lines are sold in pairs.

New manufactured transmission oil pan for the Ford C6 transmission as found on 1967-73 Cougar and Mustangs, big block and small block engines. Very high quality heavy gauge steel.Replaces Ford part number C6AZ-7A194-A.

New manufactured transmission slip yoke for either C-4 automatic transmission or small block manual 3 or 4 speed manual transmissions. Ford 1965-1973. 28 splines and 1-1/16" U-joint caps.

New manufactured transmission yoke for a T-5 5 speed transmission.

Reproduction transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy our used support, as these reproductions are inferior to the originals, and to be honest, they simply do not fit well.

Used transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy this used support as compared to the reproductions. The repros we offer are inferior to the originals, and to be honest, they simply do not fit as well.

Used C-4 vibration damper for 1968 Mercury Cougars built after 1-2-1968. Transmission tail shaft must have the provision for this bracket. C4 transmissions with either 289 or 302 engines. Shown in the 1968 Chassis Assembly Manual on page 55, aka 4980 assembly. Two different styles of these are found on Cougar c4 transmissions. Most have been discarded or damaged, limited supply on hand.Replaces Ford part number C8WY-4A263-B.

Used inner steering column tube for the tilt / tilt away for the Mercury Cougar or Ford Mustang. This unit fits within the outer steering column and is specific to 1968. Ford part # C8AZ-7212-D. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used inner steering column tube for the tilt / tilt away for the Mercury Cougar or Ford Mustang. This unit fits within the outer steering column and is specific to 1969. Ford part # C9AZ-7212-F. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Grade B speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G

This is a cost saving unit when you have a functioning system that just runs slow. The original motor will often make noise and fail to turn in cold weather. This solid state unit will cure that and will sequence your lights fast and silently with no cleaning or adjusting of the points like your original mechanical unit.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is...

New Old Stock turn signal switch for fixed steering columns on 1968-69 Mercury Cougar and Ford Mustang.Replaces Ford part # C8SZ-13341-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

New Old Stock turn signal switch for any 1969 Mercury Cougar or Ford Mustang with fixed steering columns. This switch will also fit fixed column Ford's 1968-1969 Ford Crown Victoria / Full Size / LTD / Fairlane / Torino / Falcon / Galaxie & 1970 Mercury Comet / Ford Falcon / Early 1970 Ford Maverick / Mercury Comet without locking steering wheel & all 1968-1969 Mercury Comet's Ford part # C9AZ-13341-B.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the...

Our turn signal switches are made by the original supplier to Ford from the original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This...

Quality switch that is getting increasingly hard to find these days. This same switch was used in the 1977-1979 Ford Thunderbird / 1972-1976 Ford Fairlane / 1977-1979 LTD II / Ranchero / Torino and Elite / 1975 Mercury Monarch without Instrument mounted windshield wiper switch / 1974 - 1976 Mercury Montego*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist...

1968 Mercury Cougar / Ford Mustang complete ashtray assembly with lighter.The manufacturer claims that it will fit a 1967, but this one is about 1/4 inch shorter over all compared to the 1967 unit. *NOTE* Will only fit the 1968 dashes.Click on images to enlarge. ...

Used standard grade "B" under hood main wiring harness located in the engine compartment. This harness has plugs for the headlights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where the grade "A" harnesses will be rare uncut beauties. 1967 Mercury Cougar Standard models only with AMP warning light. Not compatible with XR7...

Sold individually, two required per car. These are brand new, not rebuilds. We do not have the 4 bolt upper ball joint version available at this time. Replaces Ford Part #: C7DZ-3082-A. Fits 1967-70 Mercury Cougar and Ford Mustang. We have found that this economy version does not fit 1971-73. There just is not enough clearance for this unit to bolt into the shock tower. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Sold individually, two required per car. These are brand new, not rebuilds. Please click onto the listing of our NOS arms to see side by side comparison pictures. We do not have the 4 bolt upper ball joint version available at this time. Replaces Ford part # C7DZ-3082-A. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power.

Metal portion of the driver side rear interior panel on a 1969-70 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Grade A used, no obvious dents or rust.Basic Ford part number is 7631005. 

Metal portion of the passenger side rear interior panel on a 1969-70 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Grade A used, no obvious dents or rust. Basic Ford part number is 7631004.  *Note - Excludes Late 1970 with larger power window bezels.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...