All Products

Brake switch jumper wire, 4 inch long extension. Bridges the under dash wiring harness and the brake light switch. Not used on many cars, we suspect that it was used on the assembly line when the brake switch plug didn't reach the brake switch. Adding one of these jumpers, saved time from re-routing the under dash wiring harness. Ford master part numbers: C5AZ-14489-C, C8ZA-13K408-A and C8ZZ-13K408-A

Used jumper wire that connects the tilt-a-way door jamb and to the underdash harness.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Electrical junction block for use on 1971-73 XR7 models or 1971-73 Ford Mustang with options such as convertible, power seat, power windows, or rear defog. This combination insulator / junction block is for securing a circuit breaker, and mounts near the starter solenoid. Made from black Bake-O-Lite, Grade A used, may have some discoloring, but not damage.Replaces Ford part number D0SB-14448-A or D0SZ-14448-A.

Electrical junction block for use on 1971-73 XR7 models or 1971-73 Ford Mustang with options such as convertible, power seat, power windows, or rear defog. This combination insulator / junction block is for securing a circuit breaker, and mounts near the starter solenoid. Made from black Bake-O-Lite, Grade B, these will have some chipping or cracking present. Replaces Ford part number D0SB-14448-A or D0SZ-14448-A.

Direct plug in solid state replacement, no modifications needed. We highly suggest considering not purchasing this unit and invest in the all inclusive unit. All of the original sequential components in the trunk of your Cougar are mechanical and will in time fail. It is much more cost efficient to buy the all inclusive unit than to purchase them one by one as they fail. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the...

No modifications needed, just open the trunk and plug the unit into your original wiring! We highly suggest considering not purchasing this unit and invest in the all inclusive unit. All of the original sequential components in the trunk of your Cougar are mechanical and will in time fail. It is much more cost efficient to buy the all inclusive unit than to purchase them one by one as they fail. This reproduction is an exact replacement for this original unit. This updated relay will...

Good used metal part that is not bent or heavily rusted. Will need to be repainted. This mounts at the top front corner of the driver side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B. You may also need the attaching screw. Replaces Ford part number C7WY-6531491-B or C7WB-6531491. Fits 67 Cougar Fits 68 Cougar Fits 68 Mustang with body code 65B This icon...

Good used metal part that is not bent or heavily rusted. Will need to be repainted. This mounts at the top front corner of the passenger side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B. You may also need the attaching screw. Replaces Ford part number C7WY-6531490-B or C7WB-6531490. Fits 67 CougarFits 68 CougarFits 68 Mustang with body code 65B ...

Reproduction keeper clip that attaches to the secondary articulating stabilizer arm and slides into place to secure the pin that holds the arm.

Chrome screw used to mount the rear interior panel keeper.Sold individually.

Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford #: C7AZ-6222053-A.

Reproduction economy trunk / glove box key. These keys DO NOT have the Ford logo.Replaces Ford Part #: C7AZ-6243562-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford Part #: C7AZ-6243562-A.

Key reminder buzzer for 1970-71 Mercury Cougar and Ford Mustang. Also used on 1970-72 Lincoln MKIII and Thunderbird. Can also be stamped DOAB-13150-B, DOAB-13150-E, and DOAB-13150-F. Ford master part number D0AZ-13150-E. All buzzers are bench tested prior to shipping.NOTE: This buzzer is for ignition key reminder with two posts. The four post ignition / headlight buzzer can be found here.Click on images to enlarge. ...

Key reminder and headlamp buzzer for 1970 Mercury Cougar and Ford Mustang. Also used on 1970 Lincoln MKIII and Thunderbird. Ford master part number D0WB-13150-A. All buzzers are bench tested prior to shipping. NOTE: This buzzer is for ignition AND headlight reminders with four posts. The two post ignition buzzer can be found here. Click on images to enlarge. ...

Key reminder and headlamp reminder buzzer for 1972-73 Mercury Cougar and Ford Mustang. Also used on Many other Ford, Mercury, and Lincoln vehicles in this time frame. Can also be stamped D2AB-13150-A1A D2AB-13150-A2A. Ford master part number D0AZ-13150-E. All buzzers are bench tested prior to shipping.

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the ignition / door key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the trunk / glove box key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

New Walking Cat key fob featuring embossed lettering and walking cat on nickel plated steel attached to leather. A great collectors item or gift idea.

This listing is for a Walking Cat keychain multi tool. We haven't been able to find much information on this, but it's definitely a cool item to add to your collection. Features a chrome plated swing out tool with a few flathead tips and nub-style phillips tips. 

Quality part for your C-4 but will work on the C-6 67-68 transmission. Measures 10.2" long. Replaces Ford Part #: C6OZ-7A187-D.

C4 Automatic transmission kick down cable kit for all 1967-68 Mercury Cougar and 1966-68 Ford Mustangs. Kit includes kick down cable assembly, accelerator kick down lever, retracting spring, and related hardware.

Kickdown return spring for 1967-68 Mercury Cougar with C4 transmissions, and 1967-69 Mercury Cougar with C6 transmissions. Same for 1965-69 Ford Mustang with C4 and 1967-69 with C6. Actual Ford part number is C5ZZ-7B146-A.

Used on both 351 2V and 4V motors equipped with the C6 transmission. Approximately 26-1/2" with red color code. The comparison picture with two rods side by side are the 71 - 73 FMX and C6 rods. *NOTE* Many assume the C6 was only available with a 351 equipped with a 4V but in fact you could get a C6 with a 351 2V in 1971 - 1973.

According to the Master Parts Catalog, this rod was used on all 1969 Cougars equipped with a C6 transmission which includes the 390IP / 428CJ / 428SCJ. Our research and in hand examples off original Cougars would differ. Because of the different intake manifold used on the 390, Autolite carburetor vs. Holley and different exhaust manifolds we have found that the 1969 390 IP / C6 is distinctly different than the 428CJ and stands on its own by not interchanging with any other Ford product. ...

This rod was used on all Cougars 1971 - 1973 equipped with a 351 and FMX transmission both 4V and 2V. Approximately 27" Black color code.

This reproduction rod is made from stainless steel and weighs slightly more than the original.

This rod is correct for the 351 Cleveland 2V only and is approximately 27". A red paint daub was found on this rod, by trying to expose it with steel wool, it was almost erased. This would explain why we rarely find rods with the original paint daub in place. Slightly shorter than the 4V rod and has a lower connection point to the carburetor.

This one year only rod is correct for the 351 Cleveland 4V and is approximately 27". This rod originally had a light blue paint daub near the carburetor. It is a little longer than the 2V rod and connects to the carburetor at a slightly higher point.

Unique to the 1970 351w with FMX. Originally came with a light blue paint daub at the top.

Used on both 351w 2V and 4V FMX transmissions in 1969. Approximately 17-1/2" long with a black color code paint daub on the end closest to the carburetor. This is not correct for any 1970 Cougar equipped with a 351 Cleveland or Windsor motor. *NOTE* Although the MPC lists this part as 1969 only it does in fact apply to the 1970 Cougars equipped with the 351 Windsor two barrel motor. Not only did Ford confuse the public by giving both the 1970 351C 2V and 351W 2V the same engine code "H" in...

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part numbers D1WB-6502345, D2WB-6502345, D3WB-6502345.

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part number D1WB-6502344, D2WB-6502344, D3WB-6502344. ...

These were installed behind the kick panels on 1967-68 Cougars & the 1968-69 Fairlane, Torino, Cobra and Cyclone equipped with a factory AM-FM or AM-8 track radio. Easy to install considering you have a built in template behind the kick panels that are easy to cut out. These will accept common after-market speakers in multiple depths. For more discussion on kick panel speaker options, check out this thread. If you only are looking to buy one, please call, we often times have an odd number in...

These were installed behind the kick panels on 1967-68 Cougars & the 1968-69 Fairlane, Torino, Cobra and Cyclone equipped with a factory AM-FM or AM-8 track radio. Easy to install considering you have a built in template behind the kick panels that are easy to cut out. These will accept common aftermarket 5-1/4" speakers in multiple depths. Sold as a pair. For more discussion on kick panel speaker options, check out this thread. Replaces Ford Part number C8OA-19A067-A ...

Reproduction kick panel insulation for the 1967 - 1968 Mercury Cougar or Ford Mustang 

Exact reproduction made by Daniel Carpenter. Injection molded black plastic. Very nice. Much thicker and more durable than other reproductions. Sold as a pair. Replaces Ford Part # : C9ZZ-6502344/5

Kick panels for the 1967 and 1968 Mercury Cougar that include 6 1/2" coaxial (2 way) 100 watt speakers. Available in black, but can be sprayed to match your interior. Sold as a pair. For some discussion on kick panel speaker options, check out this thread.

Great way to update your sound system without cutting door panels or other original parts. Great fit and finish, easy installation. Pioneer speakers are 4ohms, 6 1/2" coaxial (2 way) 160 watts per speaker, for a total of 320 watts max output! Only available in black, but can be painted to match your interior with flexible paint. For more discussion on kick panel speaker options, check out this thread.

Kick panels for the 1967 and 1968 Mercury Cougar that are formed to accommodate speakers. Speakers are not included. These are designed for those who would like to choose their own speakers. Available in black, but can be sprayed to match your interior. Sold as a pair. These now come pre-cut for a 5 1/4 inch speaker. For more discussion on kick panel speaker options, check out this thread.

Sold as a pair. The overlay bonded to the plastic really gives a feel and look of quality to these kick panels. For more discussion on kick panel speaker options, check out this thread.*NOTE* These units may require some slight modification to fit perfectly in your unique Cat or Pony.

Sold as a pair. The overlay bonded to the plastic really gives a feel and look of quality to these kick panels. For more discussion on kick panel speaker options, check out this thread.

Knee pad as found on select 1968 Mercury Cougars. This grade A version will not be separating from the metal strip. Not a common option, your Cougar would have a line of mounting holes across the lower dash and above the glove box if your Cougar originally came with a knee pad. We don't always have these in stock in this condition. Call for desired color, but plan on spraying with a quality vinyl dye for best results. Black is our most popular requested color, and we will probably always be...

Knee pad as found on select 1968 Mercury Cougars. This grade B version will be separating from the metal strip, and or may have warpage. Not a common option, your Cougar would have a line of mounting holes across the lower dash and above the glove box if your Cougar originally came with a knee pad. We always have these in stock in this condition. Call for desired color, but plan on spraying with a quality vinyl dye for best results. This pad is different from the Mustang version which is...

Reproduction cigar / cigarette lighter for the 71 - 73 Cougar.