Transmission

New Old Stock Ford C4 or C6 transmission modulator valve for 1967-73 Mercury Cougar or 1965-73 Ford and Mustang. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs. Ford part number C4AZ-7A377-B.

Stainless Steel Transmission Modulator Line for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang with the C6 transmission.

O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.

Replacement rubber material pan gasket for all 1965-73 C4 Ford transmissions. 

Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops. 

1969 Ford four speed shifter rebuild kit. Kit includes tension spring, steel clip, threaded machined shaft, pair of roll pins, pair of dowel pins, and two bolts. Information indicates that all 1969 4 speed shifters are the same across all car lines and for all engines. Link to the Ford shifter linkage expert. Check out our video on rebuilding your shifter below: ...

This clip secures the clutch pedal rod end as it comes through the clutch pedal hanger.C8AZ-2B277-A

This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.

C6OZ-7A533-C. Clutch Pedal Rod To Firewall Seal. Much better than repro. Also fits 1966 Mustang / Fairlane / Comet and others.

Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal. 

1967-69 Mercury Cougar and 1965 - 1969 Ford Mustang shifter handle for automatic transmissions. We find this smaller early style chromed shifter handle in lots of 1969 Cougars, we believe that there was a transition period before the C8OZ-7213-A was used. This is the base model shifter handle with both black buttons, and set screws. Ford part numbers C5ZZ-7213-F, C5ZZ-7C488-M, C5ZZ-7C488-D. Click on images to enlarge. Check out our video on rebuilding your shifter below: ...

1969-72 Mercury Cougar and Ford Mustang shifter handle and buttons, for automatic transmissions. This is the base model shifter handle with correct black buttons, and set screws. Deluxe shifters were larger and had simulated leather wrapping. Ford part numbers C8OZ-7213-A, C8ZZ-7C488-A, and C8ZZ-7C488-B. Click on image to enlarge. Check out our video on rebuilding your shifter below: ...

C8ZZ-7400-D4Assembly 4 Speed manual transmission shift control assembly for any 1968 Mercury Cougar and Ford Mustang. Small block 289 and 302 engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition. May be either large or small trunion. Subject to availability. Check out our video on rebuilding your shifter below: ...

Attractive reproduction of a very popular, over the counter Mercury dress-up accessory. The only Cougars that came from the factory with this real wood shifter were the 1970 Eliminator and 1968 XR7G. The XR7G used a gold Cougar "Walking Cat" emblem and the 1970 Eliminator used the silver emblem. Of course this will look great on any 1967 - 1973 Cougar. Click on images to enlarge. ...

Mercury Cougar shift handles never came covered in real leather from the factory but what a cool upgrade! We sell a lot of these and the feedback has been great. We also carry the original plastic covered (simulated leather) reproduction XR7 shift handles in several colors but this real leather handle comes in black only.

Attractive reproduction of a very popular, over the counter Mercury dress-up accessory. The only Cougars that came from the factory with this real wood shifter were the 1970 Eliminator and 1968 XR7-G. The XR7-G used a gold Cougar "Walking Cat" emblem and the 1970 Eliminator used the silver emblem. Of course this will look great on any 1967 - 1973 Cougar.  If you look close and compare to the pictures of our NOS handle you will notice differences, most notable is that the chrome...

Used T shift handle, originally an over the counter Mercury dress-up accessory. The only Cougars that came from the factory with this real wood shifter were the 1970 Eliminator and 1968 XR7-G. The XR7-G used a gold Cougar "Walking Cat" emblem and the 1970 Eliminator used the silver emblem.  NOTE: The chrome center of the handle has been re-chromed. Also, the emblem and wooden handle ends will not be glued together, assembly will be required. Check out our video on rebuilding...

Get a grip with this very rare find! This used original Hurst T handle, or shifter handle, is a one year only unit with no set-screw as found on the 1970 shifter. Ford part # D1OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Mint Condition NOS part for your XR7-G equipped with automatic transmission. Notice the texture or "Fur" on the Cougar. The majority are smooth from the factory. We have no explanation for this variation. Check out our video on rebuilding your shifter below: ...

Shift kit for the FMX transmission valve body for all 1969-72 and 1969-72 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.* Note - 1973 has a different shift kit, see related items.

Very hard to find 69 - 70 Shelby / 67 - 69 Cougar 4 speed shifter knob. Almost a year in development was spent to get as close as possible to original N.O.S. sample. These very rarely come up for sale used and when they do, they are expensive. Knob insert is made of metal just like original not brass. Knob also has the correct groove in middle of body like 69 version and not the earlier version which does not. Not technically correct for a 67-8 Cougar, as the 67-8 does not have the groove in...

Very hard to find 69 - 70 Shelby / 68 - 69 Cougar 4 speed shifter knob. These very rarely come up for sale used and when they do they are expensive. Correct for 1968-69 Mercury Cougar XR7 and 1969-70 Ford Shelby Mustang, all with 4 speed manual transmissions. Ford part number C8WY-7113-C. Check out our video on rebuilding your shifter below: ...

NOS Real woodgrain knob for 1968 XR7-G Mercury Cougars with the 4 speed only. One RARE little unit! Ford master part # C8WY-7213-A.*TRIVIA* Only 26 XR7-G's were built with a 4 speed transmission. Check out our video on rebuilding your shifter below: ...

Clean no nonsense look. 12MM Threads. Check out our video on rebuilding your shifter below:

Factory detailing and triple chrome plating distinguish this tubular shift handles from the rest. Cable and T-lever included. American made for quality workmanship. Replaces Ford Part #: C5ZZ-7210-M. Check out the very first Cougar in our video below! ...

Used lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

This rod is unique to 1970 because it was the first year of the lock out rod. Very hard to come by when you consider there was no 390 option for 1970. Notice this rod features two different part numbers. Adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. 428 Cobra Jet engines were the only Cougar engines to receive the C-6 automatic transmission. Shift rod approximately 17-1/2 inches long....

Set of reproduction Ford Top Loader 4 speed shift rods for 1967-68 Mercury Cougar or Ford Mustang with 289 or 302 engines only. 

Complete floor shift assembly for the 67 - 68 Cougar or Mustang. Included in this kit are the T-shifter assy, lever assy, housing and the shifter arm. Ford part numbers: C7ZZ-7210A C7ZZ-7A306B C7ZZ-7302A C7ZZ-7213M Check out our video on rebuilding your shifter below: ...

Used Hurst built 4 speed manual shift control assembly for the Mercury Cougar or Ford Mustang equipped with the manual transmission. This assembly includes the shifter mechanism, shift rods, and shift lever. The Ford MPC states that this same shifter was used on all V8 Mustangs and Cougars. This unit may be used for the 1971 edition and is in good used condition.Ford part # D1ZZ-7400-B. Check out our video on rebuilding your shifter below: ...

3 Speed manual transmission shift control assembly for any 1969 Cougar or Mustang. Control assembly only, no rods or chrome lever. C9OZ-7400-B Check out our video on rebuilding your shifter below: ...

C9OZ-7400-B3Assembly Factory 3 Speed manual transmission shift control assembly for any 1969 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 390-4V engine. Check out our video on rebuilding your shifter below: ...

D0ZZ-7400-A3Assembly Factory 3 Speed manual transmission shift control assembly for any 1970 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 351-4V engine. Check out our video on rebuilding your shifter below: ...

C7ZZ-7400-C4Assembly 4 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang and 1968's up until 1-2-1968. Big block 390 engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The 1-2-1968 date was the transition of the stronger trunion for the shifter mounting. Check out our video on rebuilding your shifter below: ...

C8ZZ-7400-C4Assembly 4 Speed manual transmission shift control assembly for any 1968 Mercury Cougar and Ford Mustang after 1-2-1968. Big block 390 and 428CJ engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition. Check out our video on rebuilding your shifter below: ...

C9OZ-7400-AAssembly 4 Speed manual transmission shift control assembly for any 1969 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on all V8 Mustangs and Cougars. Check out our video on rebuilding your shifter below: ...

Excellent high quality reproduction of the automatic transmission shifter bezel / indicator assembly for the 1967 and 1968 Mustang without console and 1968 Mercury Cougar XR7-G with XR7-G console. While not technically correct, this bezel can also be used on non-console Cougars (1967-1968) without modification. Ford part # C7ZZ-7D443-C. Check out our video on rebuilding your shifter below: ...

Used automatic shifter bezel / indicator assembly for all Mercury Cougar and Ford Mustang with or without consoles. These are the best used ones from our inventory. These will have some minor issues with the chrome plating and most often need some detailing on the black pebble grain. Consider also purchasing a new seal, shift indicator lenses may or may not meet your requiements. Doesn't meet your requirements? We have very nice quality 1969-70 reproduction shift plate bezels also available....

Black plastic shifter bezel / indicator assembly for all 1971-73 Mercury Cougar and Ford Mustangs. Good used bezel for use with or without console or consolette. The chromed metal 1969-1970 version of this shifter cover is a very nice upgrade for 1971-1973 owners. Replaces Ford part # D1ZZ-7D443-A. Check out our video on rebuilding your shifter below: ...

Used automatic floor shift bezel for all 1967-68 Mercury Cougar with automatic transmissions without factory consoles. Grade A will have almost zero pitting in the chrome, honestly the best available. The rubber piece where the shift lever comes out will also be torn, can't be helped.  Check out our video on rebuilding your shifter below: ...

NOS automatic floor shift bezel for all 1967-68 Mercury Cougar with automatic transmissions without factory consoles.Check out our video on rebuilding your shifter below: This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and...

Metal core base as original, correct texture. If you have a 1970 with a Hurst four speed then the one with the rectangular hole is correct for the Hurst shifter. Replaces Ford part # C9ZZ-7277-A. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

C8ZZ-7210-A 4 Speed shift lever with round reverse lockout provision. For any 1968 Mercury Cougar and Ford Mustang until 1-2-1968. The early lever can be identified by measuring the distance between bolt holes. 1-13/16" spacing between the holes is the C8ZZ-7210-A lever. *Note - Must be used with Trunion C5ZZ-7210-D, sold separately.

C8ZZ-7210-C Shift lever for all Mercury Cougar and Ford Mustangs after 1-2-1968. This 1968 lever can be identified by measuring the distance between bolt holes. 2" spacing between the holes is the C8ZZ-7210-C lever. *Note - Must be used with Trunion C8ZZ-7210-D, sold separately.

C9ZZ-7210-A Shift lever for all 1969 Mercury Cougar and Ford Mustangs. Manual 3 speed only, 4 speeds are different. *Note - Must be used with Trunion C9OZ-7210-B, sold separately. Check out our video on rebuilding your shifter below: ...

D0ZZ-7210-B Chromed "Hurst" labeled shifter for all 1970 - 1971 Mercury Cougar and Ford Mustangs with factory installed 4 speed transmissions. Tough part to find loose, most will be attached to the correct vintage Hurst Competition shifter mechanism. The 1970 Ford master part number is D0ZZ-7210-B, 1971 is D1ZZ-7210-A. These shifters originally came with the "Hurst" T handles installed. These shifters will not come with a "T" handle. Check out our video on rebuilding your shifter below: ...