Other Mouldings

Reproduction passenger side (right hand) quarter window moulding / trim for the Mercury Cougar. This unit also comes with a used aluminum mounting bracket. Some refer to this unit as a "Hockey Stick" or "J moulding" and it mounts at the base of the rear quarter windows. These mouldings almost always need to be replaced due to pitting or having holes drilled in them to fasten them in place. We have found that this 3M product works great for bonding these mouldings / trim to the mounting bracket...

1969 - 1970 Cougars came factory equipped with stainless trunk mouldings and 1967 - 1968 Cougars came equipped with anodized aluminum trunk lid mouldings. However if you ordered a 67-68 service replacement deck moulding from Ford anytime after 1968 you would have received a stainless steel replacement. We recently obtained 15 of these that were stored improperly where the packaging had deteriorated and the mouldings showed shelf wear. We sent them out to be polished and the results are...

This is a freshly restored 1969-70 original stainless steel deck lid moulding. It has had all minor dings and creases it may of had professionally removed and has been polished to a mirror like, better than N.O.S. finish. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967-68 Cougar is that it will not match the aluminum corner mouldings perfectly. Seven clips are...

This option REQUIRES sending your core in advance. This is a freshly restored 1969-70 original stainless steel deck lid moulding. It has had all minor dings and creases it may of had professionally removed and has been polished to a mirror like, better than N.O.S. finish. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967-68 Cougar is that it will not match the...

Used stainless steel deck or trunk moulding / trim for 1969-70 Mercury Cougar, including convertible. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967-68 Cougar is that it will not match the aluminum corner mouldings perfectly. This being a used, means that it will have minor scratches, and a small dent or two. Save your old mounting clips, these are sold without...

Contoured stainless steel trim for the driver side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A15-A Our grade B door glass trim for 1969 will have heavy scratches that will not come out and the small bend over tab at the top will be bent or missing. The part will not be broken and will function just as good as our grade A part. Here is the 3M product used to glue this trim to the glass.Ford part #...

Used grade "B" driver side (left hand) vertical glass trim window glass for the Mercury Cougar or Ford Mustang coupe or convertible. This stainless steel trim will have light scuffing or scratches, primarily on the outside surface. Plan on purchasing new rubber weather stripping. Will not fit Mustang fastback (Sport Roof) models. Ford part @ D1ZZ-6529953-A.

Contoured stainless steel trim for the passenger side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A14-A Our grade B door glass trim for 1969 will have heavy scratches that will not come out and the small bend over tab at the top will be bent or missing. The part will not be broken and will function just as good as our grade A part. Here is the 3M product used to glue this trim to the glass.Ford part #...

Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Restored driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang convertible. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. When you purchase one of our stainless trim parts you are paying for the removal of dings and scrapes as well as the polishing of the part.  Ford...

Restored exterior driver side (left hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the bottom side. If your cores are missing studs then you will receive like parts in exchange. The studs can be reattached to the bottom side so do not discard those lose parts! If you have questions about your...

Restored exterior passenger side (right hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the bottom side. If your cores are missing studs then you will receive like parts in exchange. The studs can be reattached to the bottom side so do not discard those lose parts! If you have questions about your...

Used driver side (left hand) exterior windshield pillar post moulding for the Mercury Cougar. Sold on an exchange basis only. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. With a bit of elbow grease and time, you can make those trim pieces look better than new! Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* If you have any questions about your cores,...

Restored passenger side (right hand) exterior windshield pillar post moulding for the Mercury Cougar. Sold on an exchange basis only. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. With a bit of elbow grease and time, you can make those trim pieces look better than new! Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* If you have any questions about your...

Upper and lower fuel filler door trim pieces for 1969 and 1970 Mercury Cougars, all models. Finish and quality of this reproduction is superior to NOS as shown in the comparison photo below. Notice the blem spot on the NOS on the right? In order to help keep costs down on some of the reproduction items we left off the black detail paint as shown. NOS on the left Repro on the right Looks great assembled. You may or may not want to mask and spray gloss black paint to replicate the stripe like on...

Upper and lower fuel filler door trim pieces for 1969 and 1970 Mercury Cougars, all models except 1970 Eliminator which were black. To receive core credit back your cores must have only light pitting and no broken studs. Original Ford part number C9WY-65405-A for the lower and C9WY-65405A48-B for the upper.

These are BLEMISHED right and left hand set of 1/4 panel window mouldings. As you can see from the first two pictures above, these blems will have some minor bubbling or small dings in the chrome. These will be great for a daily driver if you're not worried about a few small imperfections. Some refer to these as "Hockey Sticks" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due  to pitting or holes having been drilled...

This is right and left hand set of 1/4 panel window mouldings. Some refer to these as "Hockey Sticks" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due  to pitting or holes having been drilled in them to fasten these in place. We have found that this 3M product works great for bonding these parts in place permanently. *NOTE - Remember to remove the aluminum brackets from the bottom of your old hockey sticks,...

This aluminum ninety degree bracket is what fastens the XR7 chrome boot moulding to the quarter panel. The beltline weatherstip also attaches to it. This part is only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb. You can find our reproduction pair of brackets here. ...

These aluminum ninety degree brackets are what fastens the XR7 chrome boot moulding to the quarter panels. The beltline weatherstip also attaches to them. These parts are only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass

This aluminum ninety degree bracket is what fastens the XR7 chrome boot moulding to the quarter panel. The beltline weatherstip also attaches to it. This part is only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb.You can find our reproduction pair of brackets here. ...

Spot on reproductions of the 1969-70 Quarter Window "Hockey Stick" Moulding priced below what you can have pit free originals re-chromed for. We have found that this 3M product works great for bonding these parts in place permanently. Included with the moulding is super strength 3M double sided, trim tape.Ford part number C9WY-6529035-A.*NOTE* Remember to remove the aluminum bracket from the bottom of your old hockey stick, it is needed to attach to the car and for attaching the outer...

Reproduction driver side (left hand) passenger side (right hand) pair of quarter window mouldings / trim with used mounting brackets attached. Some refer to these as "Hockey Sticks" or "J" mouldings. They mount at the base of the rear side windows and almost always needs to be replaced due to pitting. We bond these to the mounting brackets in house with a liberal application of 3M Windo-Weld #08609. The factory bonded them together with 3 studs that were heat peened / swedged. Ford part...

This is the right hand or "Passenger Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place.We have found that this 3M product works great for bonding these parts in place permanently.Ford part number C9WY-6529034-A.*Note - Remember to remove the aluminum bracket from the bottom of your old hockey...

Chromed quarter window moulding or 'hockey stick' mounting bracket for the driver side only of 1969-70 Mercury Cougars. Coupe only, will not fit convertibles. Also attaches the outer window fuzzy or belt line kit component. Aluminum construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C9WY-6529035-A

Chromed quarter window moulding or 'hockey stick' mounting bracket for the passenger side only of 1969-70 Mercury Cougars. Coupe only, will not fit convertibles. Also attaches the outer window fuzzy or belt line kit component. Aluminum construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C9WY-6529034-A

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD individually. See related items for kit of 10 screws. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.

Contoured stainless steel trim for the driver side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A15-A. Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Used (poor condition) weather strip may or may not be in place. Please go to our rubber section to select the new rubber strips...

Unlike our un-restored used door glass trim and are sold in pairs only. If you are doing a concours correct restoration then these would not be for you as they have been "over restored" to a mirror like finish. The down fall of having such a mirror like finish is they get finger prints on them every time you touch them. The good part is they look HOT! Very nice touch to that resto-mod that cannot get enough bling.When sending cores, they must be in good shape or an upgrade core fee will apply....

Contoured stainless steel trim for the passenger side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A14-A Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Sold separately, please choose between driver or passenger side. Used (poor condition) weather strip may or may not be in place....

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation and water spots from glass, aluminum, chrome, and rubber. 

Sold as a pair. New to the market as of 2009. Take a look at our many pictures below of these bezels installed with original backing plates and lenses. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Check...

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact.

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact. NOTE - When sending in your core, light pitting on the upper edge is acceptable. Heavily pitted trim will not be accepted.

Reproduction driver side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...

Used driver side (left hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5645. Shipping will have...

Reproduction passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...

Used passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5645. Shipping will...

Grade "A" driver side (left hand) bezel with no pitting, ready to install and use as-is. Ford part # C9WB-13504 for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Check out this LED...

NOS driver side (left hand) taillight bezel for the Mercury Cougar.Ford part # D0WY-13489. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send...

Good used passenger side (right hand) driver grade quality bezel with minimal, light pitting, ready to install and use as-is. The pitting found on this grade "B" bezel will be light and almost entirely restricted to the top surface which means it will only be seen when the trunk lid is opened. Ford part # C9WB-13449 for the passenger side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars...

Ultra rare, highly sought after NOS bezel. This is a costly part but when you factor in the price of a clean core and the $400 (approximate) cost of restoration, the cost is understandable. Keep in mind a restored part will never have the exact look of a NOS part. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

Here is a time and money saving package deal for the person restoring their 1970 Cougar. This package includes: Hood lip mouldings Fender extension mouldings Deck lid moulding Drip rail mouldings (specify w/ or without vinyl top) Nine piece front and rear window trim Front and rear Award Winning Bumpers Keep in mind we will often give extra core value trade in for items we may be low on. Please call before sending extra parts for trade value. All parts are show quality. The bumpers are triple...

Set of seven used clips with reproduction stainless steel acorn nuts. These fit the best when using an original aluminum deck lid moulding on a 1967 or 68 Cougar. In 69-70 a stainless deck trim was used and the clip was all metal with no plastic coating. For more insight on this tricky trunk trim, check out our video below: ...

Left side factory stainless steel door guard.

Right side factory stainless steel door guard.