Steering

Restored wood rimed steering wheel 1967 Mercury Cougar. This is a one year only, Cougar only steering wheel that is correct for the XR7 or Standard Cougar. We must have a good core to start with. If yours is literally falling apart, it is a goner... This wheel does not come with the three spoke horn bar or button as pictured. The bolt on items are sold separate and are shown for display purposes only. Please call for available colors. *NOTE* This item carries a $325 core charge that you will...

These are cracked core wheels as taken from a parts car. The Center pad is not included and you can count on the rubber switch being rock hard. This wheel is for restoration purposes and we cannot guarantee that we will have all colors in stock at all times. The three wheels shown here are random examples and are not what you will actually be getting when you order. Most colors in stock, call for color, or leave desired color in the comments section of your order. ...

This restored three spoke, rim blow steering wheel was used on all Cougars 1970-73 except the Cougars equipped with standard interior or on rare occasion the 1973 Cougars that came with the rare 2 spoke leather wrapped wheel. The Cougars equipped with standard interior used a two spoke wheel with the horn button located in the center pad. If you choose to send in a core for exchange it will need to be a clean one as we will not restore steering wheels that have huge cracks, severe UV damage or...

Good used (but not perfect) wheel ready to bolt on as is and use on your daily driver. Will show some degree of minor separation on the wood-grain to colored portion of the wheel and at least one crack. Very rare that we have more than one of these in stock so the chances of getting the color you desire is rare. Please call prior to purchasing for colors, condition and stock on hand. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Used Two Spoke Steering Wheel Pad for the 1969 Mercury Cougar or Ford Mustang. Grade B pads will have minor scuffs and scratches and will need to be repainted. Keep in mind that the pad pictured is just a reference photo and not the actual color you will receive.  Leave a note in the comments section of your order and we will try our best to match your color.

Perfect condition with no fading, scratches or dents. When the emblem is pulled, you will see minimal difference between the area that has been covered for decades and the area that has been exposed. Very rare find indeed!

The horn switch is embedded in this soft part. Limited colors on hand, call for availability. White plastic is prone to cracking due to shrinkage and age. Most will have a crack or two. Ford part number is D0ZZ-13915-A

A grade pad has not shrunk to the point that the center section will not fit well, it will not be curling and overall will be pliable. We rarely have more than a couple colors on hand but if you state your preference in the comments section we will try to accommodate.

Correct for standard and decor level interiors. No guarantee you will get your color of choice. Comes as shown with bezel, emblem and vinyl surround. Engineering number as seen on back of bezel reads C8AA-3D754-A

Nice used driver side strut rod that fits all 1968-69 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1968-69 Torino, Cyclone, Ranchero. 1968-69 strut rods are the same as 1970-73 strut rods, but 1968-69 rods have stepped down threads at the end. Ford part number C8OZ-3468-B. Sold as a bare strut rod, we also offer the used hardware for installation...

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a much better value than the Chinese rods we sell. This listing is for the driver side only. Compared to what you will find in most regions of the country these would be considered to be very clean in terms of rust damage.*Note - 1970-73 strut rods work equally well.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a much better value than the Chinese rods we sell. Compared to what you will find in most regions of the country these would be considered to be very clean in terms of rust damage. This listing is for the Passenger side only. *Note - 1970-73 strut rods work equally well. ...

This listing is for a premium quality pair of 1968 - 1969 original strut rods in grade "A" used condition. What sets them apart from our grade "B" rods is they have a smooth finish, no pock marks from rust. This is for the person who is doing a show car and wants the very best, original correct parts that can be found. The reproductions are made in China and work fine but they are different on every detail and do not come with the specialty bolts that attach the rear on the arm to the lower...

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a better value than the Chinese rods we sell.*Note - 1970-73 strut rods work equally well.

D0AZ-3C511-F Steel bracket that mounts to the engine block for adjusting the power steering pump. For any 1971 Cougar and Mustang with 429CJ engines with or without air conditioning. Additionally this bracket fits 1970 - 1971 Torino / Cyclone / Ranchero with 429CJ engines. *Note - Must be used in conjunction with the D0AZ-3A732-A pump bracket.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

Used one year only door jamb mounted switch for activating the tilt column.

NOS fixed column turn signal switch for the 1967 Mercury Cougar or Ford Mustang. This is a later service replacement turn signal switch, it may have an extra wire or two, and the wire lengths may be longer than the factory original. Ford part number C7ZZ-13341-F Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems....

NOS fixed column turn signal switch for the 1970 - 1972 Mercury Cougar or Ford Mustang.Ford part number D2AZ-13341-CNeed help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Replacement turnsignal switch for all 1968 Mercury Cougar and Ford Mustang with fixed (non-tilt) steering columns. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. The relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to...

Our turn signal switches are tested and working. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch.Replaces Ford part # D2AZ-13341-C. Replaces Ford...

Inner tie rod end for 1970 Mercury Cougar and Ford Mustang with or without power steering and either drum or power disc brakes. Quality reproduction part. Sold individually, two needed per car. Replaces Ford Part #: D0ZZ-3A131-B.

Original (concours correct) vacuum hose with green and white stripes. This hose set is in great condition. Only good for 1968 Cougars and Mustangs. THIS IS A VERY RARE ITEM*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Good fit, correct satin finish. Replaces Ford part # D1ZZ-13932

Good used bezel with appliqué still intact. Ford part number D1ZZ-13932-A.

Reproduction tube seat set for all 1968-70 Mercury Cougar and Ford Mustang. Also some 1967 Cougar or Mustang control valve with the 5/16" fitting. Please note that early 1967 control valves had 1/4" fittings.

Reproduction machined tube seat set, for ram cylinder and control valve on early 1967 Mercury Cougar and Ford Mustang with the 1/4" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that starting in mid to late 1967, the control valves had 5/16" fittings all the way to 1970.

Cancelling cam for the 67-69 Cougars and Mustangs with fixed columns. This cam is what returns your turn signal switch to the off position. This is not the same cam which comes inside tilt columns.

This is a stock photo, the actual lever we have will most likely be worn and will not be as nice as the one pictured. Grade A speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we may price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G This icon means that we're looking to buy...

Reproduction turn signal switch connector for your 67 Cougar or Mustang. Work with either tilt or fixed columns. This is the connector that attaches the turn signal switch to the main dashboard wiring harness.

This is a used 1967 tilt/away turn signal switch without cruise control.

Quality switch that is getting increasingly hard to find these days. This same switch was used in the 1977-1979 Ford Thunderbird / 1972-1976 Ford Fairlane / 1977-1979 LTD II / Ranchero / Torino and Elite / 1975 Mercury Monarch without Instrument mounted windshield wiper switch / 1974 - 1976 Mercury Montego*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist...

One required per car, includes Phillips screw.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

This connects the vacuum release valve to the vacuum system*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used vacuum hose for the steering column release valve used in the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. Regular vacuum hose can be used to replace this hose if you are missing the original. However, it will not be correct. This nice original FoMoCo hose has the correct ribbing, stripes and comes with the firewall grommet. If you are missing this piece and you want your car to be right, this is a must have.

Reproduction vacuum hose with green and white stripes. Every effort has been made to make this hose set as close to the originals as possible. The correct thickness and rubber type means it won't kink or lose vacuum when exposed to the hot temperatures under the hood.

Reproduction Tilt Steering hose for the 69 Cougar or Mustang. Correct in every way, this reproduction is made to be an exact fit for your original hoses.

Vacuum / electric tilt away solenoid for the 1968 Mercury Cougar and Ford Mustang. These vacuum tilt solenoids are tested and guaranteed to work. When bench testing the 1967-69 tilt away release solenoid, verify that there is continuity between the two electrical spade connectors. No continuity means the the windings in solenoid windings are bad. This is a bad solenoid. Next, put vacuum to the lower port (10-17 inches of vacuum) any handheld or car vacuum source will work. The solenoid housing...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used vacuum reservoir for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This is a 1967 only design that is very hard to find in rust free condition with a working vacuum check valve. Beware of substitutes as there are close facsimiles with different sized nipples, different brackets or plastic built in check valves. These versions off later model cars...

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used wiring cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Unique to the 1968 and 1969 tilt column, fixed column version will not fit on a tilt without modification. Ford part number C8ZZ-13376-A or C8ZZ-13376-B.

Quality reproduction of the tilt column wiring harness for the 1967 Mercury Cougar and Ford Mustang. Two harnesses as shown in the wiring diagrams. 

Steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1968 - 1969 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968 - 1969, Ford, Mercury, & Lincoln. Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

Of all of the XR7-G emblems we sell, this one may be the closest to original. This is a nice upgrade for your 1968 Cougar whether it is the standard, decor, XR7 or XR7-G model. The picture above shows the new emblem next to one pulled from a XR7-G parts car.