Fuel

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with 390 or 428 Cobra Jet FE big block 1967-68 Mercury Cougar and Ford Mustang with automatic transmission.Ford part number C7ZZ-9725-A.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block 1967-68 Cougars with manual transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968. These assemblies are just the main shaft only, and do not come with the accelerator pedal or the throttle linkage. These made in Taiwan assemblies are pretty decent looking but for less money we have original FoMoCo which with a little TLC will look better and the fit is always superior.Ford...

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with any factory Cougar V8 engine. 289, 302, 390, or 428CJ Cougars with manual transmissions.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with any 1969 Mercury Cougar unless equipped with factory speed control. *Note - not for use with 1969 factory cruise control.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with any 1970 Mercury Cougar.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with all 1971 Mercury Cougars and 1972 Cougar up until 6/19/1972. Accelerator cable attaches with a clevis pin.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with 1972 Mercury Cougars built after 6/19/1972, and all 1973 Cougars. Has a hole for either a green or blue plastic bushing on the cable end.

Reproduction carburetor spacer plate vacuum port smog plug. Spring clamp included.

Reproduction Smog Pump Pully Bolt for the 1967 - 1968 Mercury Cougar or Ford MustangSold individually 

Reproduction black Holley "Sniper" fuel injection conversion carburetor for the 67 - 73 Cougar or Mustang. Upgraded Sniper II also now available! Dual Pattern bolt on carburetor replacement, designed to fit 4150 Flange & Spread Bore manifolds - (Spread Bore Sealing Plate Part #9006 is recommended)Throttle body mounted ECU – no extra boxes to mountSupports up to 650hp with Four 100 Lb/Hr InjectorsOnly 4 Wiring Connections Required! (Battery +, Battery - , Switched Ignition & RPM)Includes...

The #1 EFI conversion system just got better! Introducing Sniper 2 EFI - a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. Holley took everything that they learned from the original Sniper EFI system and added 14 new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple...

Easy to replace, keeps correct tension on your gas pedal.

Replaces Ford Part : C9OZ-9760

Replacement throttle pedal spring for your 71 - 73 Cougar or Mustang. Easy to replace, keeps correct tension on your gas pedal.

Higher quality and higher tension spring than the spring offered by most Mustang/Cougar parts dealers. Replaces Ford part #: C5ZZ-9737-B or C7ZZ-9737-B

Reproduction Concours Accelerator Return Spring for the 1968 Mercury Cougar / Ford Mustang

"L" shaped bracket that mounts to the rear carburetor mounting hole for attaching the return spring. Bracket faces forward when installed. *NOTE* This bracket is a bit shorter than the 4V version.

These are the straps that hold the gas tank in place. 2 required, sold individually.Replaces Ford part number D1ZZ-9092.

These are the straps that hold the gas tank in place. Sold as a pair.Replaces Ford part number D1ZZ-9092.

New strip caulk for the Mercury Cougar or Ford Mustang. These units come in one foot strips and are used for sealing the front fenders to top of aprons and for sealing the fuel tank flange to the trunk floor. They are also used for sealing the floor drain plugs, gas filler necks, door panel water shields, plus many other components that are fastened to the body. This box contains 60 individual strips of black non-hardening caulk.

This screw / stud seems to always be missing. This stud is just a little longer than stock to allow installing the Hi-Po / 427 GTE air cleaner. Fit most Autolite 4V carburetors assembly. Zinc plated for years of service. Size: 4 1/2 inches 1/4-20 X 1/4-20 threads.

This is the Left hand or driver side spring that holds the rear license plate or fuel door in the upright position. Fits all years of Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-B

This is the right hand or passenger side spring that holds the rear license plate or fuel door in the upright position. Fits 1967-68 and 1971-73 Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-A

This is the spring that holds the rear license plate or fuel door in the upright position. Fits 1969-70 Cougar.Ford Part #: C9WY-13455-A

Bracket that mounts to firewall for accelerator shaft. 1971-73 Mercury Cougar and Ford Mustang. 

Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine.Cable length 22.50 inches long.  *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.

Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine. Cable length 24 inches long, check your application. There were size differences between the 2V and the 4V engines. Replaces Ford part number D3ZZ-9A758-C. *Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that date, I think it was much earlier, than July 1972. ...

Cable length 22.50 inches long. Has clevis and pin on the end for attaching to the throttle pedal assembly. *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.

Throttle cable for many 1972 and all 1973 Mercury Cougar and Ford Mustang H code 351-2V engines. Cable length 23-3/4 inches long. Uses a green plastic bushing to attach to the throttle pedal. We believe that the MPC is wrong on the length. Our observations are that the 2V cable is longer than the 4V version.Replaces Ford part number D3ZZ-9A758-B.*Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that...

Throttle cable for many 1972 and all 1973 Mercury Cougar and Ford Mustang Q code 351-4V engines. Cable length 23 inches long. Identified by the blue plastic bushing on the throttle pedal end of the pedal. We believe that the MPC is wrong on the stated length, the 4V cable is shorter than the 2V version.Replaces Ford part number D3ZZ-9A758-C.*Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that...

Ford part #: C9ZZ-9A758-A. All V-8 engines. The plastic portion that is designed to cover the cable at its furthest point by the carburetor will be broken. This is how the vast majority are for 1969, very rare to find a perfect one. Notice there are two versions for 1969, one has a plastic connector that mounts to the firewall and the other version is metal.

This is a damaged but functional part. The plastic will be broken near the end thus exposing the cable.

Replaces Ford part #: C9ZZ-9A758-A.  This updated Throttle cable is decent quality. Thicker stranded cable, correct dimensions with a good fit. A basic replacement cable. Approximately 23" in length.

Reproduction throttle cable for the 1970 Cougar or Mustang. Replaces Ford part number C9ZZ-9A758-E

Kit comes complete with accelerator linkage rod, bushings and clip kit and return spring. Replaces Ford Part #: C5ZZ-9A702.

Great little kit that is a big time saver! Correct in detail, every 40 year old Cougar needs this kit! Replaces Ford Part #: C5ZZ-9A702-MK.

Correct texture Gas Pedal, includes stainless steel trim.

Reproduction Accelerator Pedal for the 1969 and 1970 Mercury Cougar

Black moulded plastic pedal pad for all 1967 and 1968 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Stainless surround trim available too - Part number C5ZZ-9735-A.

Black moulded plastic pedal pad for all 1969 and 1970 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Stainless surround trim available too - Part number C9OZ-9735-A.

Black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Ford part number: D1ZZ-9735 or D1ZZ-9735-A Stainless surround trim available too, part number D1ZZ-9735-B.

Accelerator pedal assembly that mounts to the engine firewall. For use with any 1969 Cougar or Mustang WITHOUT factory cruise control.

Reproduction Concours Correct throttle return spring.Replaces Ford Part # : C9ZZ-9737-A

Concours Throttle Return Spring for the 390 / 428CJ / 428SCJ Manufactured after 4-9-69

Correct spring, black phosphorus plated. Does not have the same tension as original spring. We also have a Concours spring that has the correct tension. Replaces Ford Part #: C5ZZ-9737-B.*Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1967 Mercury Cougar and 1964 - 1967 Ford Mustang with 289 engines. Ford part number C5ZZ-9A-702-A. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.

Good reproduction of the 1967 throttle rod for 289 engines. It will fit on 1968 with any 289 or 302 engine with Ford Autolite carburetors. Will also fit most Holley and Edelbrock carburetors too. We also sell used versions of both 1967 and 1968 small block throttle rods. Consider also purchasing a linkage clip, see related items.Reference from mercurycougar.net: Best guys to always talk to about Cougars...will take the time on the phone with you, call you back if you leave a message, got all...

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang with 289 or 302 engines. Ford part number C8ZZ-9A-702-A. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.