Exterior Fasteners

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...

Fits Standard and XR7

Reproduction master exterior fastener kit for the Mercury Cougar Standard and XR7. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Fender Splash Shields (front of fender) Fender Splash Shields (rear of fender) Battery Tray Hood and Hinges Cowl Panel Shock Tower Braces Hood Levelers Hood Latch and Catch Fender Extensions Quarter Panel Extensions Trunk Latch...

Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.

Bolt for installing the front bumpers on any 1969-70 Mercury Cougar or Ford Mustang. Threads into the front frame rails. 4 needed per car. Sold individually#56362-S

Fits Standard and XR7 Sold as a Kit as Pictured.

Reproduction bolts for the deck/trunk lid latch for the Mercury Cougar or Ford Mustang. This is a set of five bolts and will fit both the standard and XR7. Total of 5 bolts used 1969-73, 1967-68 Cougars will only use 2. We think that Mustangs use 5 on all years 1967-73. AMK F-227 Check out this video

Fits all models.

Rear Valance Hardware kit contains 2 bolts, 2 clips and 2 nuts. "Almost" correct reproduction that functionally works great. Plated to prevent rust.See related items for a more complete fastener kit, which includes the pan head Phillips screws. Replaces Ford Part #: 372719-s100.

Complete front and rear bumper mounting hardware for the 1970 Mercury Cougar.

Reproduction clip for attaching the 1969 front fender extension moulding / trim and the 1970 hood moulding / trim found on the Mercury Cougar. The 1969 application calls for 2 of these clips along with 1 larger clip per side. If you need the larger clip for the 1969 front fender extension moulding / trim, you can get'em right here. The hood lip brightwork for the 1970 requires 4 per side.  *NOTE* The threaded stud on this clip is a little longer than the original ones. This...

Used clip for attaching the moulding / trim to the front fender extension on the Mercury Cougar. Three of these clips (with long studs) are used per side to attach the 1970 aluminum extension moulding / trim. We do not currently offer a proper reproduction for this clip. We do have this reproduction clip here and it will work for the top positions, but the stud is to short to work on the lower portion of the fender extension moulding / trim. *NOTE* Some 1970 Cougars used 2 of the 1969...

Used front fender extension moulding / trim clip for the Mercury Cougar. This is the largest of the three clips required to attach the aluminum 1969 fender moulding / trim to the extension. One is used on each side at the tail (larger part) of the trim piece. This unit is for the purest. If originality is not as important to you, you can get the inexpensive reproduction here.

Used clip for attaching the front fender extension moulding / trim on the Mercury Cougar. The fender extension moulding / trim is sometimes called the eyebrow moulding / trim. This piece of brightwork requires a total of 3 attaching clips, 2 smaller clips and one larger. If you need the larger clip, you can get'em right here! This used original clip is for the purest who values originality. If originality is not an issue, you can get our inexpensive reproduction clip here and save a...

Reproduction large moulding / trim clip for the rear quarter extensions and front fender extensions on the Mercury Cougar. The molding / trim on the 1967-68 rear quarter extension and 1969 front fender extension both require 2 different sizes of clips to properly hold them in place. For the 1967 and 1968 rear quarter extensions, you will need one of these large clips and 1 smaller clip per side. For the 1969 Cougar you will need 1 of these larger clips along with 2 smaller clips per side. This...

Reproduction clip for attaching the hood lip moulding / trim on the Mercury Cougar and six are required. We do offer good used originals here for the purest, but these will work great at half the cost.

Used hood lip moulding / trim clip for the Mercury Cougar. This unique little clip is found only on the 1969 hood lip moulding and six are required to mount your aluminum hood trim. Be forewarned, there will be varying degrees of surface rust found on these used clips and will rarely look mint. These units are high dollar and are for the purest whee originality is of the utmost importance. If originality is not an issue, you can get our inexpensive reproduction clip right here and save a...

Used hood lip moulding / trim clip for the Mercury Cougar. Ten of these clips (five per side) are required to mount the two aluminum "L" shaped hood lip mouldings to the 1970 hood. These clip are for the purest who places a high value on originality. If originality is not an issue, you can get our inexpensive reproduction clips here and save a little of that hard earned money.

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

Used clip for the stainless steel rear deck / trunk lid moulding / trim for the Mercury Cougar. This clip will also work on the 1967-68 aluminum rear deck / trunk lid moulding / trim. Seven of these units are required per moulding / trim and the acorn nut will have some rust on it. If originality is not a issue, you can get our reproduction clip here and save a little of that hard earned income. For more insight on this tricky trunk trim, check out our video below: ...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This particular clip is used on many Ford cars throughout the 60's and 70's.This listing is for a box of 100 clips. We recommend buying...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

Replaces Ford Part # : C9ZZ-6503406Sold Individually.

C9ZZ-6503406-A Front windshield lower moulding retainer clips. 7 clips required per car, sold individually.

Windshield washer hose clip that holds the hose up under the cowl. Concours quality

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.

This is the sub-kit you would have received when you purchased a stainless steel service replacement deck moulding for your 1967 - 1970 Mercury Cougar. The original clips used with a 1967 - 1968 aluminum deck lid moulding would have been similar but would have had a plastic shell surounding the metal clip. For more insight on this tricky trunk trim, check out our video below: ...

Replaces Ford Part #C7AZ-6243629-A. Not used on 1967-78 trunk locks.

Fits Standard and XR7 Sold as a Set as Pictured.

These reproduction door hinge bolts are for the Mercury Cougar and Ford Mustang and fit both standard and XR7 Cougar. They are sold in a set of 24.Intended for the 1968-70 hinges that are stamped steel, and not cast iron like 1967 hinges.

Sold individually. Zinc (dark silver) finish.Little known fact: these aren't Phillips head screws, they are actually Pozi head / Pozi-Driv screws. While you can usually get a large Phillips screwdriver to work, the correct tool for these fasteners is a size 4 Pozi bit.

Self threading white plastic. Used on front and rear valances.Sold individually.

Complete front and rear bumper mounting hardware for the 1969 Mercury Cougar.

Sold as a Kit as Pictured.

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits Standard and XR7 with front bumper guards.

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits standard and XR7 Sold as a Kit as Pictured. Check out this video

This reproduction hood latch and catch screw and U nut kit fits both the Standard and XR7 and is sold as a kit as pictured.

This reproduction hood latch vertical support screw and U nut kit fits both the Standard and XR7 and is s sold as a kit as pictured.

This is a Mustang kit and it includes 4 screws, 2 metal nuts, 2 self-threading plastic nuts and 2 anti-rattle bumpers as pictured.For Cougar, you need this kit plus 2 more plastic nuts, found here.

Fits Standard and XR7

Correct Fit and finish for 1967, and works for 1968. Connects the overhead roof console to the mounting bracket. The only difference between the 67 and 68 kits are that the 67 screws are chrome and the 68 are zinc. The zinc will discolor over time, so we suggest using the 67 kit on a 68. Replaces Ford Part #: 519A58

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits Standard and XR7

This kit includes all hardware needed for attaching the scoops to the rocker panels on the sport special rocker mouldings. Includes all screws and studs to attach the scoops to the end of the rockers, and to attach everything to the the vehicle.

This kit mounts the wing to the pedestal.