Brake Lights

Clever tool that keeps the piston stationary in your brake distribution block. It is as simple as centering the piston and screwing in this tool, of course your have to catch the groove in the piston. Leave in until brakes are completely bled and functioning. Remove and install your brake warning light switch.

Reproduction brake light switch for the Mercury Cougar and Ford Mustang equipped with manual brakes. High quality replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. Replaces Ford part # D1ZZ-13480-A.Here are some pictures of the 2008 Prowl Show hosted by the Cascade Cougar Club. Click on images to enlarge. ...

Reproduction bushing for the master cylinder push rod where the switch and brake pedal converge. Two required per car and the bushings are sold separately.Ford part number C5DZ-2B129-B

Clip or X-washer for attaching the emergency brake lever inside the rear brake drum. Fits 8 and 9 inch rear axles. Literally used on most all Ford products from 1965-73 and likely beyond. Also called a retainer for the parking brake lever pin. The long ears get squeezed with a good set of pliers for attaching. Replaces Ford number 91A-2106. 

New hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Replaces Ford part number 380699-S.

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1076 WHITE Led Plasma back up light bulb for your 67-68 or 71-73 Cougar, Mustang or anything else you might have that takes an 1076 bulb. Please note that these bulbs are ground sensitive. Specs: Power: 7.5 Watts Brightness: 300 Lumens Total life expectancy: 30,000 hours 2" Tall (1 3/8" extends out of the socket) Comparison image - Click to view full-size: Check...

1967-68 and 1971-73 Cougar/Mustang used bulb 1076 for Backup Lights, see part # 12175 As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further.  These WHITE "Plasma" LEDs are a direct replacement for 1156 and will fit anything you might have that takes an 1156 bulb (or other bulbs with the same base configuration, such as 97 and 1003 bulbs).  Basically good for every car from 1950 to 1990 that uses a 1156...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Plasma LED 1157 replacement bulb in YELLOW for your parking / running lights. Much brighter than stock, more responsive, and less power draw. We won't go so far as to call these little guys AMBER, but they're definitely yellow. Good for your 67 - 73 Cougar, Mustang or anything else that takes a dual-filament 1157 bulb for marker lights or turn signals. Specs: Power: 7.5...

Used brake switch plug end, the one that plugs into the brake pedal switch for the brake lights. These often times get hot and partially melt. Easy to change, no cutting or splicing of wires. The female spade plug end just releases from the plug end, look for the release tab for beside the wire on the back.

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with power brakes. High quality replacement brake light switch, but the appearance is not original. Ford originally called this unit the stop lamp switch. Replaces Ford Part #: D1ZZ-13480-B.

Reproduction brake light switch for the Mercury Cougar and Ford Mustang equipped with power disc brakes. This is a high quality replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. Replaces Ford Part #: C9VY-13480-A.

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with both power drum or disc brakes. This switch fits the 1967-68 for power drum or disc brake applications, and 1969-70, this switch fits power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C7ZZ-13480-B or C9ZZ-13480-B.Fits: 1967 Mercury Cougar (power drum or disc)1968 Mercury Cougar (power drum or disc)1969 Mercury Cougar (power disc)1970 Mercury Cougar...

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Ford Part # 380699-S