All Products

C5OP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1967 - 1968 Mercury Cougar with any 289 or 302 engine and automatic C4 transmission, code W on your door tag. 1967 - 1972 Ford Mustang with 250, 289, or 302 engine and automatic C4 transmission, code W on your door data plate.  Fits the 157 tooth flex plates. There was a 164 tooth flex plate that came later. Ford master part number C5OZ-7976-A. . ...

D0ZP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1970 - 1971 Mercury Cougar and Ford Mustang with any 351 engine and automatic FMX transmission, code X on your door data plate tag. Ford master part number D0ZZ-7976-A.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Manual transmissions, include both 3 and 4 speed Top Loader transmissions. Ford part number C5DZ-6392-B. For use on 289 engines after 2-15-68. This bellhousing is only for use with the 157 tooth flywheel. This bell-housing also requires the use of clutch fork C8OA-7515-A. Shipped bare, no hardware or clutch fork. Replaces Ford part number C8ZA-6394-A.

C9AZ-14527-A1 Used on Galaxie starting in 1969. Mustang used this bezel in 1971-1972.

This used grade "A" bezel for the driver side master switch was used in the latter part of 1970 through the 1972 model year. These do not "pry" off rather they are removed by slipping a small screw driver between the bezel and door panel and depressing the clip tab so as to release it from the master switch housing. The Ford casting number found on the backside is C9AB-14A432-CNOTE: We do have a few bezels that are considered B+, and we can sell them for an adjusted price. Give us a call and...

Used grade "A" power window master switch bezel. One year only bezel for the Cougar. Good used part with woodgrain appliqué in place and good chrome.Ford engineering # D2AB-14527-A.

Used grade "B" power window master switch bezel. One year only bezel for the Cougar. Fair used part with woodgrain appliqué in place and pitted chrome. Ford engineering # D2AB-14527-A.

Here is a piece that will allow to install a modern DIN radio / CD player into your Mercury Cougar or Ford Mustang. No hacking or cutting required! *TRIVIA* Here's some alphabet soup for you. DIN stands for Duetch Industri Normen. An abbreviation for a standard in-dash radio measurement which is approximately 2 inches by 7 inches. The Germans starting using it to standardize the radio�??s in Audi�??s, BMW�??s, Mercedes, and VW�??s way back in the mid 80�?�s. ...

Grade B 68 Radio Bezel for 1968 Mustang or standard Cougar. Holes often are modified for after market radio, might have broken upper mounting ear, pitting. Email for picture or detailed explanation of current stock on hand. Ford casting number C8ZB-6504567-CNeed some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a storage compartment. The slide up doors are different between the 2 years due to the handle being different. The...

Good used part with nice emblem, woodgrain appliqué. If someone has a roll of material that resembles the burl grain pattern here we would really like to hear from you! the black paint on the edges will need to be redone. The engineering number as seen from the back reads C9WA-3D752-A. We also have examples in the $50 to $100 range that are ready to put on as is but are not show quality like this one. Call and we will walk you through our stock on hand over the phone. We usually have 40 to...

Used grade "A" bezel for the three spoke rim blow steering wheel found in the Mercury Cougar Eliminator or the decor equipped Cougar. This is the best of the best that we have in used and it will look mint.Ford part # C9WA-3D752-A.

Grade "A" driver side (left hand) bezel with no pitting, ready to install and use as-is. Ford part # C9WB-13504 for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Thinking about adding some...

Grade "A" passenger side (left hand) bezel with no pitting, ready to install and use as-is. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Thinking about adding some LED taillight bulbs to your car? Here is...

Good used passenger side (right hand) driver grade quality bezel with minimal, light pitting, ready to install and use as-is. The pitting found on this grade "B" bezel will be light and almost entirely restricted to the top surface which means it will only be seen when the trunk lid is opened. Ford part # C9WB-13449 for the passenger side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars...

New Old Stock 1973 Mercury Cougar passenger side tail light bezel, NOS. Ford part number D3WY-13489-A.

No Excuses chrome bezel that wraps around the outside of the front turn signal lens on the 1971 or 1972 Mercury Cougar. Ford part # D1WB-13237-AA.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject.Here's our...

No excuses passenger side (right hand) chrome bezel that wraps around the outside of the front turn signal lens on the 1971 or 1972 Mercury Cougar. Ford part # D1WB-13236-AA.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information...

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1967-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. As you look at our picture below you will see the repro is about half the thickness. The repro is different in every detail but will work. We also have used plates with minor damage at a reduced cost.

Nice reproduction of the 1970 - 1973 front adjusting bracket for the 351 Cleveland engines. These do not have any markings.

For any year 1967 1968 1969 1970 Mercury Cougar with an FE 390, 427, or 428CJ engine. Identified by the round dimple stamped into it. Compare the OEM used part price to the reproduction part. For restoration purposes, this bracket was factory painted satin black.

C9OZ-2212-B Left hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71086. Originally manufactured by Bendix, part number 317558..

C9OZ-2211-B Right hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71085. Originally manufactured by Bendix, part number 317559.

Complete Midland core booster with both input and output rods in place. No visible cracks in bake-a-light plunger. Will show some rust pitting, most notable on the bottom side where previous leaking master failed, but not excessive. Check out our videos below, one on how to convert a manual drum brake car to factory disc brakes, and the other on boosters, differences, do's / don'ts: This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury...

This reproduction brake booster looks and fits more like the originals than any other on the market. This is an off-shore unit, but of the many out there, it is the only one we feel you can consistently get 10 or more years out of. It comes with a 3 year warranty and no core exchange is required. If you do have a decent original core (any version 1967 - 1970 Midland or Bendix brand), we can credit you towards this unit up to $120. NOTE* This reproduction booster uses metric fasteners. If you...

Reproduction disc brake distribution block and proportioning valve assembly for the Mercury Cougar or Ford Mustang with factory disc brakes. This will also work on your 1968 - 1969 Fairlane / Torino / Montego / Ranchero / Cyclone & Cobra equipped with power disc brakes in the front if you carefully remove the wedged on stamped steel mounting bracket and reuse your original bracket. Mounts to the driver side fender apron with two nuts. With this assembly you will get a distribution block, brake...

Power disc brake distribution block with proportioning valve. Mounts to the driver side fender apron with two nuts. Plan on testing and or rebuilding before installation. Rebuild kits available here. You'll also need hard lines and the brake warning switch, which is available new or used. Ford part # C8ZZ-2B257. Here’s a video to help you rebuild the distribution block so that you can corral your Cat or Pony without fearing for your life. ...

This reproduction stainless steel power disc brake line kit for late production Mercury Cougars (built after Feb. 1967) is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.Late production brake lines were routed under the steering column. John Booze's 1967 FE ...

This reproduction stainless steel standard drum brake line kit for Mercury Cougars and Ford Mustangs equipped with the 9 inch rear end and 28 spline axles is bent and dropshipped from the supplier when it is ordered. It is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

This standard drum brake line kit for early production Mercury Cougars (built before Feb. 1967) is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

Reproduction OE steel standard drum brake line kit for the Mercury Cougar. It is item is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless steel. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.  NOW AVAILABLE WITH THE CORRECT REAR BRAKE LINE FITTING FOR THE COUGAR!  The Mustang fitting is .323" whereas the Cougar...

This reproduction power drum brake line kit is for Mercury Cougars and Ford Mustangs equipped with the 8 inch rear end and 28 spline axles. It is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

This reproduction stainless steel power drum brake line kit for Mercury Cougars and Ford Mustangs equipped with the 9 inch rear end and 28 spline axles is bent and dropshipped from the supplier when it is ordered. It is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

Two-piece Stainless Rear Axle Brake Line Set 67, 68 & 69 Mercury Cougar and Ford Mustang with 9"-28 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help with any...

Late production brake lines were routed under the steering column.

Also correct for some 1967 models with proportioning valve at front

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with a manual transmission and manual drum brakes.This unit features a shorter arm than power brake pedals and is for use with a clutch pedal. The picture may show hardware and pedal pad with trim, but the pedal is shipped bare.Ford part # D1ZZ-2455-D.

Used brake pedal for the Mercury cougar equipped with power brakes and a manual transmission. This is for use with the non-collapsible 1967 steering column and with a clutch pedal. Longer arm than manual brake pedals. Keep in mind automatic pedals can be trimmed down to work as manual transmission pedals. Pedal shipped bare, picture may show hardware and pedal pad with trim.*NOTE* You will have to drill holes in your existing manual brake pedal hanger to accomomdate the power brake pedal....

Unique pedal that works with the wider collapsible 1968 steering column and with a clutch pedal. Longer arm than drum brake pedals. Keep in mind automatic transmission brake pedals can be trimmed down to work as manual transmission pedals. Pedal shipped bare, picture may show hardware and pedal pad with trim. *Note* On some 1968 Cougars you will have to drill holes in your existing pedal hanger (many are pre-drilled) to accomomdate the power brake pedal. Since systems with a vacuum booster...

For use with a clutch pedal. Longer arm than drum brake pedals. Pedal shipped bare, picture may show hardware and pedal pad with trim. 1971-73 Mercury Cougar or Ford Mustang with 3 or 4 speed manual transmission and disc brakes.Replaces Ford part number D1ZZ-2455-A.

Driver side disc brake spindle for 1971-73 Mercury Cougar and Ford Mustang. Ford part number D1OZ-3106-A left hand or drivers side disc brake spindle. Guaranteed to be a flawless used part. Ford casting number D1ZA-3107-AA.

Passenger side disc brake spindle for 1971-73 Mercury Cougar and Ford Mustang. Ford part number D1OZ-3105-A right hand or passenger side disc brake spindle. Ford part number D1OZ-3106-A left hand or drivers side disc brake spindle. Guaranteed to be a flawless used part. Ford casting number D1ZA-3107-AA.

Reproduction driver side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability, the...

Reproduction driver side drum brake spindle. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Good used driver side (left hand) brake spindle for the Mercury Cougar or Ford Mustang equipped with front drum brakes. Our spindles shipped bare, without any hardware. We inspect every piece for spun bearings and any galling to the spindle shaft. These are getting hard to find because after market disc brake conversions require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Ford part # D0OA-3108-F.

Used driver side drum brake spindle for 1971-73 Mercury Cougar and Ford Mustang, as well as those mid sized Ford and Mercury's. Ford casting number D1OA-3108-AA.

Reproduction passenger side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability,...