All Products

Molded "S" shaped vacuum hose. Feed hose from the smog pump to the Carter anti-backfire distribution valve.

Core C-4 Transmission valve body for any 1967-68 Mercury Cougar or 1967-69 Ford Mustang with code "W" transmission code on the door tag. This is only for 1967 through 1969 transmissions with P-R-N-D-2-1 shift pattern. Also known as the 8 bolt valve body. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in...

Core C-4 Transmission valve body for any 1968 Mercury Cougar or 1968 Ford Mustang with code "W" transmission code on the door tag. This is only for 1968 transmissions with P-R-N-D-2-1 shift pattern. Also known as the 8 bolt valve body. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket,...

Core FMX Transmission valve body for any 1970 Mercury Cougar or 1970 Ford Mustang with code "X" transmission code on the door tag. This is only for 1970 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is the...

C6ZZ-6582-H Smooth chromed valve cover without "Powered by Ford" embossed in the metal. Correct on 1967 DGS Mercury Cougar and optional on 1965-67 Ford Mustang with 289 engines. Ford master parts catalog shows a right and left version of this cover those numbers are C6ZZ-6582-H & C6ZZ-6582-J. *Note - This is a used chrome valve cover. The plating was pretty low quality back in 1966-67 and these will show rust pitting. For best results we recommend the painted version of this valve cover...

C8WY-6582-C  Pair of Cast aluminum running cat valve covers for 1968-70 Mercury Cougar or XR7-G with X code 390-2V , S code 390-4V, or R code 428CJ engines. Original valve cover, FE running cat valve covers were not side specific. One cat will face forward and one will face backwards on your Cougar. These are die cast aluminum not sand cast. Also note that these are tall pent roof valve covers, you will need the special double extended air cleaner snorkel if using these valve...

C9ZE-6583 Cast aluminum valve cover. Correct on 1969-1970 Mercury Cougar and Ford Mustang with 428CJ engines. This is the plain finned aluminum valve cover. Ford master part number C9ZZ-6582-B. Casting number can also be C9ZE-6583-B. Sometimes called 1969 Shelby valve covers. *Note - Some 1969-70 428 Super Cobra Jet engines came with a different style of  "Snake" finned aluminum valve covers.

SNAKECOVER Cast aluminum valve cover. Correct on some 1969-1970 Mercury Cougar, Ford Mustang, Shelby GT-500 with 428CJ and 428SCJ engines. This is the 'Snake' aluminum valve cover. Ford master part number C9ZZ-6582-B.

C9ZE-6583-G Cast aluminum valve cover with. Correct on 1969-1970 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engine. This is the finned aluminum valve cover. Ford master part number is C9ZZ-6582-C. *Note - Most, if not all 1969 Boss engines came with a chromed steel valve cover. Research did not turn a part number for that valve cover. Likely it is a chromed 351C valve cover. If you have the part number for the stamped steel chrome Boss 302 valve cover please share. ...

C9ZE-6583-G Cast aluminum valve cover with. Correct on 1969-1970 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engine. Additionally, correct for 1971 Ford Mustang Boss 351. This is the finned aluminum valve cover. Ford master part number is C9ZZ-6582-C. Finned cast aluminum valve covers with drippers inside. See photos.  *Note - Most, if not all 1969 Boss engines came with a chromed steel valve cover. Research did not turn a part number for that valve cover. Likely it is a...

Reproduction set of after market cast aluminum valve covers with COBRA 428 lettering. Fits any FE style Ford engine, including 390, and 428 cubic inches.

Here is a pair of cast aluminum running cat valve covers for the 1968 Mercury Cougar XR7-G with the F code 302-2V or J code 302-4V engine. Original valve sand cast covers, not a reproduction. Originally cast by Shelby American Inc.Ford part # C8WY-6582-B, Shelby American part number S7WE-6582-B.

C7AZ-6571-B

New old stock driver side vent window handle for any 1968 Mercury Cougar or Ford Mustang.  Drive pins and washers included.Ford part number C8OZ-5422917-B

New Old Stock passenger side (right hand) vent / wing window handle for the 1967 Mercury Cougar or Ford Mustang. Also fits 1966 Ford and Mercury mid sized cars. Ford part number C6OZ-6222916-A.

Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73.  A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...

This kit includes 2 vent frames, 2 quarter window frames and all four stainless parts that complete the frames. By purchasing this as a kit you are getting the stainless parts for almost free. Keep in mind, those who send in high quality cores in advance of making their order get the advantage of core matching. If you send in cores in advance with minimal pitting we hand select your parts to give you our best. If you do not send your cores in advance we select your parts randomly. If you are...

Used grade "A" driver side (left hand) vent window frame as it comes out of the door and is just the bare window frame. This is not a perfect part but it will look good on a low mile car that shows a little patina. The weatherstrip track that continues down into the door can be had with this part for no extra charge, please mention it in the comments section when you order online. Ford part # C7ZZ-6522205-A. Casting # C7ZB-6522223-A Check out our video below for helpful tips on disassembling...

Used grade A stainless steel vent window glass frame for the left side or driver side door on a 68 Mercury Cougar or Ford Mustang. Similar frame as the 1967

We have had this rare roof material reproduced! The material comes in a 54" wide roll and we give you twelve running feet which is more than enough to do one 69-70 Cougar (Unless you have power sunroof).

These are original amp meters converted from reading amps to reading volts. Includes new matching XR7 overlay made from top quality 3M 467MP and use 200MP adhesive. The longer 200MP adhesive is in place the stronger it binds.  Click here for a article describing the advantages of a Volt Meter.

New old stock instrument voltage regulator Ford part number C9AZ-10804-ACheck out this video of our Gauge Tester

New old stock instrument panel voltage regulator or IVR for all 1967-68 Mercury Cougar and Ford Mustang. Additionally fits 1967-68 Ford full size, 1966-68 Torino,CycloneMounts to the rear of the instrument clusters, voltage regulator for dash gauges power.  Ford part number C6DZ-10804-A. Check out the video below on our new gauge tester: ...

This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety standards. The mirror nut tool will fit over the 1967 wand, but not the 1968.

Emergency or parking brake indicator lamp and wiring assembly. Tested and working red indicator light which was found optionally on any 1967 Mercury Cougar standard model 65A or 65C. The 1967 parking brake light kit gets its power from the ignition switch. Ford part number C7WB-10A841-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in...

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

These used taillight mounting washers are sold individually for your Mercury Cougar. Two different inside diameters on these, we have them mixed, because they are in such short supply. Normally installed with a dollop of black goo for sealing out moisture. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems....

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C6OE-A. Found on many Ford 289 engines from 1966-67. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other casting...

Dated 6M29, December 29, 1966. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C6AE-8505-B. Found on many Ford 390 engines from 1966-67. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Two...

Dated 7C17, March 19, 1967. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C6AE-8505-B. Found on many Ford 390 engines from 1966-67. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Two different...

Dated 7C20, March 20, 1967. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C6AE-8505-B. Found on many Ford 390 engines from 1966-67. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Two different...

Dated 7G3, July 3, 1967. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-8505-H. Found on many Ford 390, 427, and 428CJ engines from 1968. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers....

Dated 7M9, December 9, 1967. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-8505-H. Found on many Ford 390, 427, and 428CJ engines from 1968. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...

Dated 8F4, June 4, 1968. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-8505-H. Found on many Ford 390, 427, and 428CJ engines from 1968. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers....

Rebuilt water pump, Ford casting C9AE-8505-A, dated 9A9 January 9, 1969. Fits any 390 or 428 Cobra Jet.

Rebuilt water pump, Ford casting C9AE-8505-A, dated 9L25, November 25, 1969. Perfect for late Dec - Jan 1970 428 Cobra Jet. 

Dated 9M6, December 6 1969. Boss 302 or 351C Ford water pump core, suitable for rebuilding. This version has a casting number of D0OE-D. Found on many Ford 351 Cleveland engines from 1970. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers....

NOS Water bypass plate for all Ford 351C engines. This is an original in the package brass restrictor plate for 1970-73 Mercury Cougar or Ford Mustang Torino etc.Limited to stock on hand. Replaces Ford Part number D0AZ-8K517-A. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Used hot water tube connector, Grade C condition. Fits 1973 Mercury Cougar and Ford Mustang with EGR valve attached to the carburetor spacer plate. "H" shaped water tube connector with fitting for vacuum thermal valve that controls the EGR valve. These are seldom seen in any condition, Grade C used will have rust through in and on the tube ends. Probably want to get some tubing to fit the inside of the connector tubes, in order to clamp down heater hoses. Vacuum thermal switch switch not...

NOS new old stock driver side (left hand) horizontal quarter window outer weather strip. This is just the one outer weather strip that attaches to the body or XR7 convertible moulding. This rubber piece is included in our reproduction Standard or XR7 convertible belt line kits for 1971-73 Mercury Cougar. Ford part number D1WY-7629733-A.

NOS new old stock passenger side (left hand) horizontal quarter window outer weather strip. This is just the one outer weather strip that attaches to the body or XR7 convertible moulding. This rubber piece is included in our reproduction Standard or XR7 convertible belt line kits for 1971-73 Mercury Cougar. Ford part number D1WY-7629732-A.

NOS weatherstrip for the driver side (left hand) quarter window in the Mercury Cougar or Ford Mustang. Ford part # C9ZZ-65214A15-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! Check out this video

Includes all five pieces. Front bow rubber seal is C9ZZ-7653986-A. Side rubber seals are C9ZZ-7651564-A, C9ZZ-7651565-A. Much better fit than reproduction, perfect for that high end restoration.

Restored driver side (left hand) aluminum channel for installing the roof side, or upper door and quarter window weather stripping. Right and left sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weather strip. Shipping...

Restored passenger side (right hand) aluminum channel for installing the roof side, or upper door and quarter window weather stripping. Passenger and driver sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip....

Original NOS part, new in box. Ford part # C5ZZ-6503110-A

Used inner and outer driver side (left hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion. *Customer Feedback*"I know Don Rush is a trusted and well...