All Products

OEM used, not reproduction. Free of rust and damage. Installation gasket, clamps, and hoses are available. Fits 1970 22 gallon non-emissions fuel tank. 49 states (non-California). This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an...

OEM used not reproduction. Rust and damage free.

Used assembly line, white plastic filter retainer for the Mercury Cougar, Ford Mustang and other Fords equipped with Midland Booster. It fits between the master cylinder and brake booster on the aluminum master cylinder spacer. The repro and service replacement filter covers are usually black not white. You can find the filter here. ...

Pair of reproduction firewall to shock tower braces for the Mercury Cougar or Ford Mustang. These Chinese made units are already painted black, so the only thing you need to do is bolt them on. However, we highly recommend that you get our superior quality used FoMoCo units right here!Replaces Ford part #'s C9ZZ-16A053-A driver side (left hand), C9ZZ-16A052-A passenger side (right hand). ...

Reproduction, nice thick firewall insulation pad for the Mercury Cougar or Ford Mustang. We actually like this one better than the "premium" version. These are pre-formed for a perfect fit and appearance and greatly reduced engine noise and heat. The A/C and non A/C versions are the same piece and will fit both A/C and non A/C cars.This pad comes with all the rubber clips needed for installation.

Reproduction thick premium firewall insulation pad with clips for the Mercury Cougar or Ford Mustang. These are pre-formed for a perfect fit and appearance and greatly reduced engine noise and heat. The A/C and non A/C versions are one in the same and this unit will fit both A/C and non A/C cars. Unlike cheap paper backed insulation, these quality pads are backed with thick rubber.

Reproduction thin firewall insulation pad with clips for the Mercury Cougar or Ford Mustang. This unit will fit both the A/C and non A/C Cougar or Mustang.

Replaces Ford Part # : D1ZZ-3513-A. For use only with 3 and 4 speed manual transmission cars.

Concourse Correct FLAPPER DOOR ASSEMBLY for vehicles equipped with ram-air. Includes: door, pivot rod, and 2 retaining clips Fits 1969 390GT and 1970 Boss 302, 351W, 351C. Replaces Ford Part #: C9ZZ-9610-A

Used convertible top flapper stopper. Technically called a "lasting", this is the thin strip of 1/16" thick metal that slides inside the sleeve of your convertible top to keep it from flapping. We will rarely have these on hand, so we've included the dimensions so that you can fabricate your own if needed. 2 required per vehicle.

Rubber coupler for connecting the drive motor and the geardrive for operating the ASC factory sunroofs. American Sunroof Corporation started using this shorter connector sometime in late 1968 on the very early 1969 cars. ASC power sunroofs (technically moonroofs since they had solid covers instead of glass) were offered on many new cars such as Mercury Cougar, Lincoln Mark series, Ford Thunderbird, and many Mopars or Dodge, Chrysler, and Plymouth cars.

Good used OEM flex plate for all 69 - 73 Mercury Cougar and Ford Mustang with 302 / 351W engines, and C4 or FMX transmissions. Not for use on a 1968 with 302. The starter ring will show wear and some will choose to replace, others have removed the starter ring and just turned it around so the unused portion of the ring will now contact the starter drive gear. ...

Brand new flex plate for all 1970-71 Mercury and Ford with 429CJ engines, and C6 transmissions. Comes complete with new starter ring gear installed as shown.

Reproduction floor pan firewall extension for the driver side (left hand) of your 67 - 68 Cougar.

These correct floor pan patches are for the 1969-70 convertible and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long and 15 1/4" wide. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

This piece runs under the floor over the transmission where the floor pan meets the firewall.

Reproduction driver side (left hand) floor pan to cowl side panel for Mercury Cougar and Ford Mustang. Normal 0 false false false EN-US X-NONE X-NONE Here's our little film to help you fortify your car! ...

This is the foil insert / decal found on a non XR7 Cougar. It's located just below the center rectangular dash vent / register. It measures 6" X 3/8".

This is a much cheaper version of the foil sound deadeners and underlays we sell. This particular insulation is basically bubble wrap with two layers of foil on both sides. Good for insulating headliners, floor pans, trunk areas, door panels, kick panels and just about anything else you might want to use it for. This insulation comes in a 48" X 72" roll. Just grab a pair of scissors and cut your shapes. You can use any adhesive you like (contact cement or weatherstrip adhesive,...

Reproduction rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1968 Mercury Cougar and Ford Mustangs. New part with a fine threaded stud, also called a pinion bumper. The correct casting number is seen on this rubber axle bumper is C3AA-4906-C, this version has fine threads. The version most often seen on the 1969-70 is C9OA-4906-A. It will have a course threaded mounting stud.

Reproduction rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1969 - 1970 Mercury Cougar and Ford Mustangs. New part with a course threaded stud, also called a pinion bumper. The correct casting number is seen on this rubber axle bumper is C9OA-4906-A, this version has course threads. The version most often seen on the 1967-68 is C3AA-4906-C. It will have a fine threaded mounting stud.

Reproduction driver side (left hand) inner front frame patch for Mercury Cougar and Ford Mustang.

Reproduction passenger side (right hand) inner front frame patch for Mercury Cougar and Ford Mustang.

Reproduction pair of frame rail / floor supports. These extend off the back of the front frame rail and give support under the front floor pan. Includes driver and passenger sides.

Reproduction driver side (left hand) inner front frame patch for Mercury Cougar and Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below:

Reproduction passenger side (right hand) inner front frame patch for the Mercury Cougar or Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below:

Reproduction driver side (left hand) outer front frame rail patch for Mercury Cougar and Ford Mustang. The outer rail has weld nuts installed for proper installation.

Brass and steel freeze plug or expansion plug set for any Ford 351C engine. 1970-74 Mercury Cougar and 1970-73 Ford Mustang. 12 piece set with threaded screw in plugs as shown. 

Brass and steel freeze plug or expansion plug set for any Ford 289 / 302 / 351W engine. 1967-70 Mercury Cougar and 1967-73 Ford Mustang. 15 piece set with threaded screw in plugs as shown. 

Brass and steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 20 piece set with threaded screw in plugs as shown. 

Used fresh air vent found in the driver side kick panel of all 1971-73 Mercury Cougar without air conditioning. Replaces Ford part number D1WY-6501935-A.

Used fresh air vent found in the passenger side kick panel of all 1969-70 Mercury Cougar and Ford Mustang with or without air conditioning. Please also see the listing for new gaskets for installation.Replaces Ford part number C9ZZ-6501934-A.

Our good used vents will not have cracks in the plastic or a rusty flapper from a leaking cowl. These are the same for AC and non AC.Replaces Ford part number C7ZZ-6501935-A.

Used front console support bracket. Held in place by 2 phillips screws at the front, under the console.NOTE: There were two versions of this bracket, a shorter version without holes and a longer version with holes. See reference photo above.

Reproduction front diaphragm for your 67 - 69 Cougar or Mustang Midland power brake booster.

All new disc brake pads are supplied to us by brand name manufacturers. Boxed set of four pads. Semi-Metallic linings. Kelsey Hayes Brake caliper system.

All new premium ceramic disc brake pads. Superior "positive mold" manufacture process provides better braking performance. OE designed shims ensure noise free operation. Ceramic brake pads are scorched to remove any impurities in the friction material. This eliminates the need for initial break-in and reduces the noise associated with pad glazing. Kelsey Hayes Brake caliper system.

This assembly is spot welded to the fender skin. Sometimes this area will be damaged in a collision but the skin will still be fine. 1969 and 1970 front fender structures are different, this is a driver side 1969 Mercury Cougar part. Due to the rarity of good fenders and the costly shipping you may want to consider repairing your fender as opposed to buying another if this is all you need.

This assembly is spot welded to the fender skin. 1969 and 1970 front fender structures are different, this is a driver side 1970 Mercury Cougar part. Sometimes this area will be damaged in a collision but the skin will still be fine. Due to the rarity of good fenders and the costly shipping you may want to consider repairing your fender as opposed to buying another if this is all you need.

This assembly is spot welded to the fender skin. 1969 and 1970 fender front structures are different. This is a 1969 Mercury Cougar passenger side structure. Sometimes this area will be damaged in a collision but the skin will still be fine. Due to the rarity of good fenders and the costly shipping you may want to consider repairing your fender as opposed to buying another if this is all you need.

This assembly is spot welded to the fender skin. 1969 and 1970 front fender structures are different, this is a passenger side 1970 Mercury Cougar part. Sometimes this area will be damaged in a collision but the skin will still be fine. Due to the rarity of good fenders and the costly shipping you may want to consider repairing your fender as opposed to buying another if this is all you need.

Reproduction driver side front inner apron for both the Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Reproduction driver side (left hand) front inner apron for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Reproduction driver side (left hand) front inner apron for Mercury Cougar and Ford Mustang.

Reproduction passenger side (right hand) front inner apron for Mercury Cougar and Ford Mustang.

Good used brace that may be lightly rusted but not ripped, but will almost always show minor repairs. This part was straightened in a vise prior to taking this picture. At this price we do not sell mangled junk, but after 40 years it is rare to find one that has never been bumped. Ford master part # C7WY-13B135-A.

Good used brace that may be lightly rusted but not ripped, but will almost always show minor repairs. This part was straightened in a vise prior to taking this picture. At this price we do not sell mangled junk, but after 40 years it is rare to find one that has never been bumped. Passenger side ones have a much less survival rate than the driver side bracket, due to the proximity of the battery.Ford master part # C7WY-16B134-A.