All Products

428CJ engines with C6 automatic transmissions. Shaft diameter 3-1/2 inches. Length 49-41/64 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.

289 and 302 engines - with C4 automatic transmissions or manual three / four speed. Shaft diameter will measure 3 inches. Length 54-3/16 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.  Ford part # C7WY-4602-E.*NOTE* This is a solid one piece drive shaft.

Select 1970 M-code 351-4V engines and FMX transmission.Shaft diameter 3-1/2 inches. Length 53-9/16 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Not a common part, currently out of stock.Ask about slip yokes. Shipping is oversized due to length.

This kit was sold by Ford Service Departments back in the day for those who were tired of their manual drum brakes. This kit includes all you will need to convert your six cylinder Mustang or V8 Cougar / Mustang from manual to power drum brakes. Technically it is correct only for a 1968 but will work on any year 67-70. The conversion carries a Ford part number of C8ZZ-2A091-A. Ford was generous and gave you both a manual transmission and a automatic transmission brake pedal in the kit. When...

Used fresh air vent duct found behind the passenger side dash panel of all 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. The flexible portion of this item is what fails most often. Anyone find a solution for a repair?Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent.Replaces Ford part number D1ZA-18637-AB, the flexible hose which is stapled to this duct is marked D1ZA-18C305-AB. This icon means that we're looking to buy this part!WCCC...

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "A" part and may have one very minor defect. This part will be damage free. Replaces Ford part number C9ZA-18C366-A.

C9ZA-18C366-A lower heater duct to floor outlet for Cougars or Mustangs without air conditioning. Used grade "B" part that will have more than one minor defect. It will have a small crack and possibly a broken or missing tab. Almost half the price of the grade "A" piece and works awesome if you don't have one at all. Want to have directed heating, we've got you covered.

Flow thru ventilation, power vent, power ventilation system, comfort stream ventilation, are some of the various names for this rare option found on 1969 Mercury Cougar, Ford Mustang and Shelby Mustang. Back in 1969 it was a $40.02 option. It allowed fresh air to be blown through a center vent. Often confusing, because it looks like half of an air conditioning system.Ford casting number C9ZA-18C299-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to...

New A/C vent hose with cam locks for your Mercury Cougar or Ford Mustang equipped with factory A/C. This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Two required per car, sold as a pair.Ford part #: C7WY-19B680 or B5A-18556-C.

Used rectangular center duct tube for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory air conditioning. Wire reinforced foam, will show some snags or signs of use. Will not have gaping holes. Was originally stapled to the center housing. Ford part number C7ZZ-19B680-B.

Used disc brake dust shield specific to the factory installed Kelsey Hayes disc brake systems on the 1967 Mercury Cougar or Ford Mustang. Right and left the same. Clean Western part with no heavy corrosion like you see on Eastern cars.Ford part # C7OZ-2K004-B.

Fuel pump drive eccentric for most big block Ford engines 1963-70. Including 352, 360, 390, 410, 427, and 428. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 3-3/8 inches in diameter. Ford part number C3AZ-6287-A.

Edelbrock Torker 351C intake manifold. Edelbrock 2760 for 351C-4V cylinder heads. Used piece, single plane. Check the Edelbrock site for the specifications.

Correct cast aluminum elbow fitting for the rear of the C8AZ-9A486-C smog pump. This elbow will have two single mounting holes. The service replacement elbow (Ford part number D4TZ-9C475-A) has two sets of double mounting holes. Correct Ford part number C8AZ-9C475-A.

Reproduction chrome heater hose elbow is for 351, 390, and 428CJ engines. Replaces Ford Part # D0AZ-18599-C Barbed End: 5/8" hose barbThreads: 1/2" NPT (Tapered Threads) For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Concourse correct 351 2bbl engine heater hose connector with a 90?� degree elbow that attaches to the intake manifold. Product discontinued by manufacturer. Know anyone else reproducing these? Let us know!

Concourse Correct 90 degree elbow that attaches to the intake manifold and provides proper clearance for the emission canister and air cleaner housing. Correct for all 1968 S code 390-4V, W code 427-4V and R code 428 Cobra Jet engines.

Elbow with water restrictor.

Concourse correct 90 degree heater hose elbow that attaches to the intake manifold and provides proper clearance for the emissions canister and air cleaner housing. Correct for all Boss 302 and 428CJ engines 1969-70.Ford number C9ZZ-18599-A.

Black plastic elbow that clips onto the air cleaner base of most 1971-73 Mercury Cougar and most other Ford, Mercury, and Lincoln cars with V8 engines. Elbow for hose from PCV valve to stock air cleaner bases.

Used original 1969-70 Mercury Cougar Eliminator dash center plate with cover. Not reproduction, notice the slight shrinkage inside the chromed bezel? Only found on Eliminators. 

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fits many 1967 - 1968 Full size Mercury cars and 1967 - 1969 Mercury trucks. This emblem measures 6 3/8" total width and the "M" is 2 1/8" tall. The bottom mounting studs located on the letter "M" and "Y"...

NOS never installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender. Sold individually Replaces Ford Part #: C8OZ-16228-D.

NOS never installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender. Sold individually Replaces Ford Part #: C8OZ-16228-D.

Nice reproduction of the factory installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender.Sold individuallyReplaces Ford Part #: C8OZ-16228-D.

Ford part number is C7WY-16098-A, casting number as seen on the back of the emblem is C7WY-16720-A. Very rare find, only used on 1967 non GT cars equipped with the S code 390.See related item Barrel nut if missing attaching clips. 3/16 inch stud.

Used Grade "A" center grille emblem for the 71 - 72 Standard Cougar. Most likely will show some fading, no pits. Ford part number D1WY-8A223-A

These were obtained from the original manufacturer and have never been mounted. Very rare find!

Rare find in NOS form! 1969 standard model Cougar, passenger side dash plate. Replaces Ford part number C9WB-6504460-A.

Due to the fact these were glued on, they are often missing. Separate "XR" and "7", Grade B used, good for a daily driver. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line workers did not even attempt to get them very well centered. Both emblems were placed on the RH side of the deck lid...

This was an adhesive emblem and has long since fallen off most cars or was removed when the car was painted. We often times have driver quality emblems available, but be aware, they will have some pitting issues.Our reproduction 67-68 pillar emblem is a good substitute.Original Ford part number D1WY-6542532-A.

Will show at least a small amount of pitting. Casting number as seen on the back reads D0WB-652803-E.

Original part in Ford box, part number C9WB-16098-A, casting number as seen on back is C9WB-16098-B

NOS front fender extension "Cougar" script. Ford Engineering number as found on the backside:  Ford number C9WB-16098-B. 

NOS front fender extension "Cougar" script. Ford Engineering number as found on the backside: Ford number D0WB-16098-A . 

This Mercury script emblem is mounted onto the driver side fender extension. This is an original part still in the Ford box, engineering number on the back of the emblem reads C7WB-16098-A, Ford part number is C7WY-16604-A.

This adhesive plaque was placed in front of the shifter on XR7-G models with a factory installed four speed manual transmission. The XR7-G shift knob had a walking Cat on the face of the knob instead of a shift pattern.

This version of the emblem was actually used on early 70's full-size Mercurys, and is almost identical to the 1969-70 version used on Cougars. In order to use it on a Cougar fuel door, the studs on the back will need to be trimmed down The only visible difference is the thinner / more numerous ridge lines in the red crest area than on the Cougar version. Casting number on this substitute emblem is D1GB-16607-AA.The original emblems were never sold as a stand alone part from Ford but rather an...

These fuel door Mercury crest emblems are a close to original reproduction. They are an economical alternative to brighten up the looks of the rear of your 1969 - 1970 Cougar. This crest was used on all models except the 1970 Eliminator. To remove your emblem we suggest grinding down the studs on the backside. To install the reproduction emblem you will need the 26120 trim clip.

These fuel door Mercury crest emblems have been lovingly restored by a long time Cougar enthusiast. They have been carefully repainted the correct colors and will really liven up the looks of the rear of your 1969 - 1970 Cougar. This crest was used on all models except the 1970 Eliminator. The engineering number on the back is C9WB-65405A92. To remove your emblem we suggest grinding down the studs on the backside. To install the restored emblem you will have to use epoxy glue. Keep in mind you...

Pretty safe to say this item will never be reproduced. We often have used in stock but they are always faded.Ford part number D1WY-8A223-A

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

We only get one of these in every couple of years or so. We often have driver quality emblems in stock. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We...

Faded but good used emblem with aluminum foil background. If you push on the swedged aluminum studs from the backside these will easily remove. The standard grill emblem with a walking cat uses the same stud configuration as XR7 so you can exchange emblems from one to another.

Rare Cougar only GT emblems. The Mustang GT emblems had different stud locations. These were used on 1968 Mercury Cougar GT models.  This emblem shares the exact same pin locations with the 1968 6.5Litre emblem, so the factory could punch holes and installed the tubular nuts in the fenders of all S and X code Cougars, allowing either emblem to be installed. The 1967 GT emblems have an entirely different stud placement from these 1968 only badges. Letter "G" is Ford part...

Same as the emblem used on the trunk lid of the 1967 -1968 Cougar.

Good used emblem with no missing studs, cracks or pitting. We rarely have this one in stock.

This is the correct emblem that came in the center of the hood moulding on a 1973 Standard model Mercury Cougar. It would not look out of place on an XR7 but of course would not be correct. Ford part # D3WY-16637-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested...