All Products

Used convertible top switch for all 1969 Mercury Cougar standard and XR7, 1970 standard Cougar (76A), all 1969-70 Ford Mustang. This switch is located over the radio bezel. Used and tested convertible top switch, it will not come with a knob. This switch was also used on Cougars with factory power sunroofs. *Note - The 1970 Mercury Cougar XR7 had the power top switch located in the convenience switch panel in the dash.

Knob for engaging the emergency flasher switch on a fixed (non-tilt) steering column. This original knob is plastic, the reproductions are chrome plated die cast.

Good reproduction of a knob that is always broken off. Made from milled aluminum rather than plastic as the originals were made. This makes it so it is not as susceptible to breaking off. Unique to Cougars with tilt columns in 1968 - 1969. Replaces Ford part number C8MY-17513-C. This part also fits the 68-69 Mustang, Lincoln, Marquis, Thunderbird and other like models with an adjustable steering column.

Used emergency flasher knob for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. These knobs are very fragile and the chrome plating will show some minor scratches and pitting. We try and keep these on hand, but the fragility makes them 'subject to availability'. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down...

Perfect fit, easy to replace and will be a great upgrade over your original scratched and or pitted knob. To remove, reach behind the dash and locate the small, round spring loaded button on the top side of your headlight switch. Depress the button while firmly grasping the knob and move back and forth until it releases. To install, firmly and quickly press the knob inward (towards the dash) with the palm of your hand.Here is a helpful youtube video on how to go about removing a headlight...

Perfect fit, easy to replace and will be a great upgrade over your original scratched and or pitted knob. To remove, reach behind the dash and locate the small, round spring loaded button on the top side of your headlight switch. Depress the button while firmly grasping the knob and move back and forth until it releases. To install, firmly and quickly press the knob inward (towards the dash) with the palm of your hand. NOTE - This does not fit Mustang headlight switches  Here is a helpful...

Headlight switch knob for any 1967 Mercury Cougar or Ford Mustang. Not the same as 1968. This is a nice detail item for concours judged cars. There is a difference between 1967 and 1968 knobs as shown in the photos. Nice used condition.  Original Ford part number C7ZZ-11661-A.

Headlight switch knob for any 1968 Mercury Cougar or Ford Mustang. Not the same as 1967, which is reproduced by Scott Drake. This is a nice detail item for concours judged cars. There is a difference between 1967 and 1968 knobs as shown in the photos. Nice used condition. Original Ford part number C8ZZ-11661-A.

Good used headlight switch knob for any 1969-70 Mercury Cougar or Ford Mustang. To remove, reach behind the dash and locate the small, round spring loaded button on the top side of your headlight switch. Depress the button while firmly grasping the knob and move back and forth until it releases. To install, firmly and quickly press the knob inward (towards the dash) with the palm of your hand. Ford part number C9ZZ-11661-A Here is a helpful youtube video on how to go about removing a...

Reproduction headlight switch knob for the 71 - 73 Cougar.

Not for use on cars with A/C. Keep in mind we also have excellent used knobs sold individually or as a set.

Don't be fooled by knobs with similar part numbers, they have longer shafts and will not work as well on your Mercury Cougar or Ford Mustang application.Ford part # D1ZZ-18830-A, and Ford casting # D1ZA-18A932-AA.*TRIVIA* Did you know that Ford called the inner (balance / tone) radio knobs "discs?"

This is one of the easier knobs to find in that it does not break easily and can be found on many 1967 FoMoCo products. Not used on Cougars with a center console and little to no differences can be seen between the different examples. One explanation for having multiple casting numbers for the same part is that Ford would use multiple suppliers for a single part. To differentiate which part came from which vendor, different casting numbers would be assigned. If there was a problem with a run...

Reproduction inner radio knob used on the Mercury Cougar or Ford Mustang with a factory center console and measures 1-3/8 inches tall. Replaces part # C8ZA-8A932-B

Rare plastic radio knob used only with the 1967 XR7 and standard Cougar console. This knob differs from the Mustang console and Cougar / Mustang non console knob in that it is deeper to clear the console pad unique to the 1967 Cougar. Ford called these rare little units "discs" back in the day Replaces part # C7WA-18A932-A

Used on early non console 1967 models and has a lower profile than the later version. We also have pitted knobs we can throw in on a order for free, just mention it if all you need is a knob that gets the job done.Ford part # C7MA-18817-A.

Unlike the plastic console knobs, the issue with these metal knobs is pitting as opposed to breaking. Very hard to find in clean condition.Replaces part # C7ZA-18817

This knob is for Cougars equipped with consoles only and then only the earliest of Cougars would have seen this plastic, lower profile, delicate knob. Very hard to find Cougar only knob that is not found on any other model. This is one RARE little dude indeed!Replaces part # C7WA-18817

Rare radio knob used only on the 1967 XR7 and standard Cougar console. This knob differs from the Mustang console and Cougar / Mustang non console knob in that it is deeper to clear the console pad that is unique to the 1967 Mercury Cougar. Early standard model Cougars with the console used a more petite version of this plastic knob. Replaces part # C7WA-18817-B

Used wiper knob for any 1967 Mercury Cougar. This version is smaller than the 1968 knob. Unlike the 1968 version, there is no set screw, and is simply pressed into place. You may need to use a bit of adhesive to hold in place. Good condition, will have a small rust pit or two.

Used wiper knob for any 1968 Mercury Cougar. This detachable knob with set screw is slightly larger than the ones found in 1967. Good condition, will have a small rust pit or two.

Used knob for wiper control switch on dash panel. Constructed of metal with chrome, may show some wear on the black painted section and flaws in the plating.Ford part number C9ZZ-17513-C.

Chrome and black knob just like the original.NOTE: This knob is correct for 1969. It will fit on a 1970, however the orientation of the pointer will be off. You can find a good used 70 knob here. Replaces Ford Part # : C9ZZ-17513

1971 - 1973 Cougar wiper control switch knob. In early (May 3, 1971) Mercury changed the knob. This is the later knob. Hex shaped knob, good used, may show some minor wear.

This knob set differs from the set used later in 1967 only in that the outer knob has a lower profile head. Keep in mind we have reproduction knobs that will work in place of these.

This set of reproduction used knobs is for 1968 Cougar / Mustangs without factory console. The exception to the rule would be the XR7G. Cougars equipped with a console need the longer version of this knob to clear the padded console face. If you happen to have a 1969 or newer radio then the radio has longer shafts and these knobs may in fact work with a console. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear...

Full set of metal radio knobs for the 1967 Mustang or Cougar. Not for use with the 1967 Cougars equipped with factory center console. Keep in mind we have reproduction knobs that will work in place of these.

Nice clean set of four used radio knobs for your 69-70 Mustang or Cougar. No peeling or cracks. The inset picture shows the used next to the new from the backside. The reproductions are shown on the right. Whereas the repros are nice, the originals are still superior. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and 68-70 AM-FM radios. White plastic reproduction spacers available here. The white...

The early Cougars had a lower profile head on the outer knob. It is assumed they beefed up the design in early in the year because the knobs were easily broken. These delicate plastic knobs are very hard to find in this condition. Only the utmost purist would care to obtain a trivial detail part such as these to make their car correct. These deeper knobs were only used in cars equipped with a factory center console. The Mustangs did not have a padded console in 1967 so this set is for 1967...

Complete five piece set for 1967 Cougars with center console. The majority of 1967 model Cougars got this improved design with stronger outer knobs. Keep in mind we have reproduction knobs that will work in place of these. Also keep in mind we will accept your incomplete set of used 67 console radio knobs for a complete set of our 1968 reproduction knobs. Give us a ring for details.

These heater control knobs are sold in a set of three and fit good and tight. It is often little details like this that separate 1st and 2nd place when judged at car shows. Replaces Ford Part #: C9ZZ-18519-A.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used lower knuckle for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This knuckle is unique to 1967 because the center hole is round. The 1968-69 features an elongated center hole.  There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* We'll give you UP TO $100 cash back for your...

Used lower knuckle for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This unit will not interchange with the 1967 tilt / tilt away. This is because the center hole on the 1967 unit is round where this 1968-69 version is elongated. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used upper knuckle for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang.  There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...

Used upper knuckle assembly for the tilt / tilt away column for the Mercury Cougar or Ford Mustang equipped with a tilt / tilt away steering column. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* We'll give you UP TO $100 cash back for your old knuckle assembly. The amount you will get back will depend upon how many usable parts that can be salvaged from your old unit. *NOTE* For tilt column service, you can contact Tony...

Good used "L" bracket for the tilt cable adjustment on the 1968 and 1969 Cougar or Mustang.

Reproduction Large Wire Loop Strap for the 1968 Mercury Cougar or Ford Mustang 

Zinc plated, visually correct copies of the original, very prone to failure... We highly recommend buying our good used latches linked here even though they may not look as pretty. No warranty on this low quality off shore part.Replaces Ford Part # C5AZ-6243200-A Check out this video

During installation, check for proper alignment with trunk latch. Trunk latch and striker should engage smoothly, both items are adjustable. We only save the rust free latches with no wear or rust, the rest are tossed. Fits 1967-68 Mercury Cougar. Ford part number C6OZ-6543252-A.

During installation, check for proper alignment with trunk latch. Trunk latch and striker should engage smoothly, both items are adjustable. We only save the rust free latches with no wear or rust, the rest are tossed. Fits 1969-70 Mercury Cougar and 1968-69 mid sized Ford Torino, Fairlane, etc. 1968-69 Mercury Cyclone, Montego, etc. Ford part number C5AZ-6243252-B.

During installation, check for proper alignment with trunk latch. Trunk latch and striker should engage smoothly, both items are adjustable. We only save the rust free latches with no wear or rust, the rest are tossed. Fits 1971-73 Mercury Cougar and Ford Mustang. Ford part number D1AZ-6543252-A.

Reproduction driver side (left hand) convertible top latch assembly for the Mercury Cougar or Ford Mustang.  

Reproduction passenger side (right hand) convertible top latch assembly for the Mercury Cougar or Ford Mustang.  

Used convertible top latch handle for the driver side (left hand) for the Mercury Cougar or Ford Mustang.Ford part # D1ZZ-7650509-A , casting # D1ZB-7650509-A

Used convertible top latch handle for the passenger side (right hand) of the Mercury Cougar or Ford Mustang.Ford part # D1ZZ-7650508-A , casting # D1ZB-7650534-AA

Keep in mind we also have these in used form. for a little more (or less) money depending on condition. This part fits all Mustangs and Cougars 1965 - 1970. Replaces Ford Part #: C5ZZ-7650509-K. Casted Pot Metal with Engineering # C4ZB-7650535-C

Used driver side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired.  Ford part number C4ZB-7650535-C.

Keep in mind we also have these in used form. for a little more (or less) money depending on condition. This part fits all Mustangs and Cougars 1965 - 1970. Replaces Ford Part #: C5ZZ-7650508-KCast Pot Metal with Engineering # C4ZB-7650534-C