All Products

D0OE-9430-A 429 Cobra Jet factory original cast iron exhaust manifold for passenger side.

C9ZE-9431-A Factory original cast iron exhaust manifold for driver side. Correct for all Boss 302 Eliminators 1969 and 1970.

C9ZE-9428-A Factory original cast iron exhaust manifold for passenger side. Correct for all Boss 302 Eliminators 1969 and 1970. Nice piece from a CA car, no damage or pitting.

351-4V Cleveland factory cast iron 4V exhaust manifold set, both correct right and left set of matching exhaust manifolds. Manifolds the same 1971-1973.

Used pair of Exhaust Manifolds / 428CJ for the 1968 Mercury Cougar / 1968 Ford Mustang 

428 Cobra Jet factory cast iron exhaust manifold set, both a correct right C8OE-9430-D and left C8OE-9431-B side matching exhaust manifolds.

428 Cobra Jet factory cast iron exhaust manifold set, both a correct right C9OE-9430-D and left C8OE-9431-B side matching exhaust manifolds. *Trivia: All 1970 428CJ's had Q engine codes. Ram air was optional and many had that option. Not sure? only way to tell for sure is with a report from Kevin Marti.

Exact reproduction of Ford's free-flowing, high-performance cast-iron exhaust manifolds used on the 428 Cobra Jet, 428 Super Cobra Jet, and GT500 Shelby's. Concours correct with original Ford logo and part numbers cast into the manifolds. NOTE: Dwayne from "The Brothers Car Collection" clued us in to the fact that the choke tube fitting on the passenger side is indexed 180 degrees off on some sets we sell. Fortunately you can carefully spin it around with vise grips so the opening faces...

429CJ factory cast iron exhaust manifold set, both correct right and left set of matching exhaust manifolds.

Factory cast iron exhaust manifold set, both a correct right C9ZE-9428-A and left C9ZE-9431-A side matching exhaust manifolds. 1969 and 1970 Boss2 Eliminators

Factory used exhaust tip from a 1968 Mercury Cougar GT-E. Fairly good condition, has some scuffing on the lips of the tips and or scuffing on the bottom edge. Factory stamped C8WX-5C262-A. A 20% discount for purchasing a pair. 

Original NOS shroud with correct chocolate brown color and texture as what came on your Cougar the day it was made. The later shrouds sold by Ford were smooth, black and the "Barnum Fibre Co. Inc." maker lettering was faint. This is a wonderful piece for that concours quality 1969 BOSS 302 Eliminator or GT350 Shelby.Ford Part number C9OZ-8146-A

Great addition to that show quality FE powered early Cougar. Unlike the reproduction this has the original part number, BARNUM BROS. FIBRE CO. INC. lettering and FoMoCo insignia at the top driver side. This was one of the last units out the door when FORD discontinued them in the 1990's. Weighs 2.70 pounds and the reproduction weighs 1.54 pounds. Ford part number C8ZZ-8146-A

This shroud was discontinued by Ford in the mid 1990's. It really is no different in appearance from our reproduction but it does weigh a hefty 2.56 pounds and the reproduction weighs 1.76 pounds. Must have FoMoCo / part numbered shroud for that show quality BOSS 302 or 351C Eliminator. Just like our reproduction, the BARNUM BROS. lettering has been ground off. This was done because Barnum no longer made the shrouds for Ford in the latter years but the tooling still had their name on it.Ford...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust and no distorted wheel lip areas from over sized tires. We really inspect the area where the fender extension bolts on well...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust and no distorted wheel lip areas from over sized tires. We really inspect the area where the fender extension bolts on well...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust, no distorted wheel lip areas from over sized tires. We really inspect the area where the fender extension bolts on well as...

This latest of a series of 68 reproduction sheet metal parts is just what the market has been waiting for! The dimensions are EXACT down to the 1/16", black primer finish is very similar to what the later service replacement parts were from Ford. The fender weighs a few pounds more than original due to being made from slightly thicker material than OEM. Keep in mind there are no shipping fees or taxes when you pick this item up in person at our shop. Next up will be deck lids, stay tuned!...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust and no distorted wheel lip areas from over sized tires. We really inspect the area where the fender extension bolts on well...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust, no distorted wheel lip areas from over sized tires. We really inspect the area where the fender extension bolts on well as...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust, no distorted wheel lip areas from over sized tires. We really inspect the area where the fender extension bolts on well as...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to be removed before installation. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2)...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to be removed before installation. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2)...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here.All front end kit parts are identical for both power and manual steering.Note: Bright orange protective covers are to be removed before...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2) Outer Tie Rods, (2) Inner Tie Rods, (1) Idler Arm, (2) Spring Perches. If you...

Reproduction Front end rebuild kit specifically for the 1967 Cougar with articulated strut rod arms. There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to be removed before installation. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2)...

Nice rebuildable core of the Carter X 4441S fuel pump for all 1968-70 428 Cobra Jet engines. Has "X" casting, 4441S stamped, dated 10B9A, February 10, 1969. Kits available for rebuilding. 

Factory original Carter fuel pump that was taken from a low mile 427 GTE in 1997. The "X" pump was used only on the Boss 302, 427, 428 and 429 Cobra Jet, and Super Cobra Jet.

Complete gauge cluster with toggle switches, lenses and gauges as shown here. This is a grade "B" set that will only need detailing and to have the plastic bezels restored to be show quality. Check out our video on dash removal and restoration: ...

This is a complete 1969 (one year only) grade "A" grille bright work set taken from a Western parts car(s) with no obviously visible cracks, pits on the face of the chrome or bends. Not perfect, but the best we can obtain, usually taken from three or more cars to make one set. This set includes two halves, two eye lids and one center section (which often we will include a reproduction in lieu of used). Brackets, hardware and actuator are sold separate but often we will throw in several pieces...

This extremely rare hood scoop insert was used on a hand full of 428 Cobra Jet Cougars made prior to September 15th, 1968. Only the early 1969 scoops will have the embossed mounting areas used to mount this grille. Click on images to enlarge. *NOTE* Often we will list items like this more for educational purposes than anything. Please do not be frustrated when you go to place an item like this in your shopping cart only to find we no longer have it. Items like this often only appear once in a...

1970 Mercury Cougar grille chrome pieces. Passenger side, driver side doors, both housings, and the center grille. Technically painted for a standard model, but can easily be detailed for an XR7. Included are the original Ford boxes as shown. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

NOS part that shows shelf wear and may need to be repainted in places. For 1967 and early 1968 Cougars built prior 12/15/1967. Can easily be made to fit 1968.  Ford part # C7WY-13A136-B (Headlamp exterior cover) C7WY-13A154-A (Headlamp hinge) Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

NOS part that shows shelf wear and may need to be repainted in places. Can easily be made to fit 1967. Ford part number C7WY-13A136-B Casting number C8WB-13A138 *NOTE* For use on 1968 Cougars built after 12/15/1967. Not for use with 1968 Cougar GT-E. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

Used grade "A" driver side (left hand) grille half for the 1969 Mercury Cougar. These will be the best we have available, taken from a Western parts car. The horizontal bars will not have any breaks or cracks, the chrome will not have any pits on the face but you will see minor pitting between the horizontal bars on the black painted areas. Often there will be a crack where the tension spring for the headlight attaches but we will include one of our grille repair clips if that is the case....

Used grade "A" passenger side (right hand) grille half for the 1969 Mercury Cougar. These will be the best we have available, taken from a Western parts car. The horizontal bars will not have any breaks or cracks, the chrome will not have any pits on the face but you will see minor pitting between the horizontal bars on the black painted areas. Often there will be a crack where the tension spring for the headlight attaches but we will include one of our grille repair clips if that is the case....

Ford casting number D0ZE-6316-A Includes all 1970 G code Boss 302 engines. Ford master part number D0ZZ-6316-A. Has the timing marks on rim. This good quality used balancer is a good option for those wanting to keep a 100% original looking appearance on a concours car that does not get driven or see high RPM's. If you have a rebuildable core D0ZE-6316-A balancer to trade, we can offer a substantial discount.*Note - Excludes 1969 Boss 302 and all non-Boss 302 engines.

Harmonic balancer or damper, core grade 1971 Boss 351 Ford Mustang. Marked D1ZX-6316-AA. Age cracks in the rubber, should be rebuilt prior to use. Groove opposite of timing marks as shown, no other visible issues. 

Note: The set you receive may not be the ones pictured and will usually be in better condition than shown. The chrome bezels will all be in good matching condition, unlike the blemished one in the picture. Call if you need more details or to check inventory on colors. Used pair of dual post head rests for the Mercury Cougar or Ford Mustang. These ultra rare head rests were an option in 1968 only and may come with some slight blemishes. Your 1968 Mustang / Torino / Thunderbird / Cyclone seat...

C8OZ-9A603-B metal shroud that attaches to the passenger side stock cast iron exhaust manifold. Works in conjunction with a metal 'S' tube sold separately (C8AZ-9652-A). R code and Q code Cobra Jet engines only.

D1AZ-9A603-C Metal shroud for all 1971 429 Cobra Jet engines including C code 429CJ non-ram air and J code 429 CJ with ram air. One piece design uses a paper and aluminum tube to bridge to the air cleaner snorkel. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested...

Ford part number C9ZZ-9A603-C for the upper section and C9ZZ-9A603-D for the lower for this two piece metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this lower section also. metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this upper section also.

Ford part number D0ZZ-9A603-C for the upper section and Ford part number D0ZZ-9A603-D for the lower section of this two piece metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - 1970 Boss 302 cars build after 9-2-1969 used this lower section. of a two piece metal shroud unique to G code Boss 302 Cougar Eliminators.

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. We rarely have in stock what we would consider a grade "A" 1967 - 1968 Mercury Cougar hood. Grade "A" 1967 - 1968 hoods have no rust...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Grade "A" hoods have no rust under the lip, nothing more than a light skim coat of filler found anywhere, no damage in the hinge...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Grade "A" hoods have no rust under the lip, nothing more than a light skim coat of filler found anywhere, no damage in the hinge...