1965 Ford Mustang

Nice reproduction of the original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds. The supplier unfortunately does not include the hardware and we have yet to source any. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on...

Reprint of an original pamphlet that was intended to help Ford techs date and identify by using the codes found on the parts. Covers all LFM models, 23 pages.

Stainless steel throttle pedal surround trim. Self attaching to part number C5ZZ-9735-E. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up.Fits 1967-68 Mercury Cougar and 1965-68 Ford Mustang.

Restored drive side upper windshield moulding, fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustang coupes.Ford part number C5ZZ-6503145-B.

The trim at the top of the windshield on the left hand side.Ford part number C5ZZ-6503145-B

Your original decades old trim will look fine... Until you place it next to a quality paint job.Ford part number C5ZZ-6503137-B.

Used driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang. These are suitable for restoration and for use your daily driver.Ford part # C5ZZ-6503137-B.

This restored OEM stainless steel lower windshield moulding / trim has been restored to a level far beyond NOS. It has been polished to a mirror like finish that is brilliant and gleaming. The term "over restored" could be applied to this part because back in the day FORD never spent the time we invested into polishing this piece. Original parts like this one always fit and look superior to "offshore" reproductions.Ford part # C5ZZ-6503148-B.

This good used original lower windshield moulding / trim has been carefully inspected to be free of small dings and heavy scratches. It will have very light scratches consistent with a classic of this age but nothing a do it yourself type could not bring to show quality on his own. This trim piece is perfect for someone wanting a trim part ready to install on their very nice driver or occasional show car. Much better fit than "offshore" reproductions. Ford part # C5ZZ-6503148-B. *NOTE* Keep in...

Restored passenger side (right had) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece will look right at home gleaming in the sun on your mint condition Cat or Pony and will definitely make your ride POP!Ford part # C5ZZ-6503144-B.

Used passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece is suitable for your lower quality daily driver or a great piece for a high quality restoration.Ford part # C5ZZ-6503144-B. 

Restored passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece is considered over restored because of the high luster and will make your Cat or Pony absolutely POP!Ford part # C5ZZ-6503136-B.

Used passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece will fit right in on your daily driver or is an excellent candidate for those of who like to restore your own parts.Ford part # C5ZZ-6503136-B.

Repro fuel pump gasket for 1967 - 1970 Cougars or Mustangs with 289/302/351W/390/428CJ engines.

This is one of the best small block Ford V-8 books on the market. It covers 260-289-302 V8 engines. Carburetor numbers, distributor numbers, covers all engine brackets, pulleys, and parts of Ford small block engines. 100's of pages with pictures, casting numbers, and explanations by year. A must for concours detailing and year by year correctness. Author Bob Mannel, covers small block V8 engines and components 1962-69. References all Ford cars that these engines came in. Mustang, Cougar,...

Nut for attaching the steering wheel on any 1967 Mercury Cougar or 1965-67 Ford Mustang.Ford number 350983-S.

New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S

Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.

Nuts and washers for attaching the rear differential carrier or pumkin or third member to the rear axle housing.Correct for all 1967-68 Mercury Cougar and 1965-68 Ford Mustang. 8 inch or 9 inch third members, all the same.

Complete engine modification specifications manual for 1960 through early 1970 Ford engines. Includes everything from the 98 CID 4 cylinder to the 460.

Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP

Hex shaped extension. Made from machined metal and Zinc plated. Replaces Ford Part # : C2OZ-9B339

Hex shaped extension. Made from machined metal. Used and road tested steel extension for installing your oil pressure sending unit. Part shipped normally will not be as clean as the one pictured, we strongly suggest cleaning the inside oil passage prior to installation, it is a used part. Fits all 289, 302, 351W, 390, 427, 428CJ engines. Several versions found on this item. Steel and aluminum construction. We have both in the bin. Please note that the 351C or 351 Cleveland engine has the it's...

VHT epoxy paint is great for a number of applications. It's a unique one step protective coating that dries quickly and doesn't require a primer. It provides excellent rust, corrosion and chemical resistance which, needless to say, is ideal for anything you're doing under your hood or under and around the body of your car. One can covers about 12 - 14 square feet.

Professional grade paintless dent removal kit. This kit is designed to work with smaller blemishes such as dents from hail, door dings, etc. Complete with universal high strength glue sticks, puller, and a variety of different sized gluing tabs. NOTE: Remove glue with 91% alcoholAlthough we work with 67 - 73 Cougars and Mustangs, this kit is good for a wide variety of different vehicles.

A needed part for giving your car a tune-up. PCV Valve fits all years; 289, 302, 351, 390, and 428 CID; V8. *Note - Not technically correct for 390-4V or 428CJ, those originally used a PCV valve with a threaded top, and the 90° elbow - part number C7OZ-6A706-A.

New pinion seal for any 8 inch third member found in 1967-73 Ford and Mercury cars. 1967-68 Mercury Cougar and all years of Mustang with 8 inch drop out rears.

Used pinion yoke for an 8 inch rear end on any 1967-68 Mercury Cougar or 1967-73 Ford Mustang. 25 splines Ford says it is for a 1260 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3OZ-4851-A.

C4ZA-3590-A Early 1967 Steering box pitman arm with 1 inch sector shaft. Power steering only, used with SMB-E steering box. Fits early 1967 Mercury Cougar and 1965- early 1967 Ford Mustang. Ford part number C5ZZ-3590-A. Caution, measure your steering box sector shaft, many of the short boxes have been changed to the 1-1/8 inch boxes. Rare part, limited to stock on hand.Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

Floor tunnel body reinforcing plate for the floor shifter on any 1967-68 Mercury Cougar or 1965-68 Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than other years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number C5ZZ-6512118-A.

NOTE* After comparing to the original pulley, we've found that this reproduction is approximately 3/16" shorter in overall height. New crank shaft pulley, single sheave small block Ford 289 / 302 351W engines up to 1969. Single V-belt or fan belt pulley, means for use with only the alternator. Not for use with power steering, air conditioning, or smog pump. Measures just under 6-1/4 inches in diameter. Single sheave crank shaft pulley with 3 bolt holes, excludes engines after 1970....

Usually ships in 3-5 business days. Replaces Ford Part #: C4DZ-7653337-A. This is a new part, not a rebuild, no core needed. Correct brackets for a Cougar, not a generic one size fits all application. 5 year warranty when used with automatic transmission fluid.

Core radiator from 1965 San Jose built Ford Mustang with V-8 engine and automatic transmission. Western Modine manufactured, stamped C4ZE-M2 and stamped date 3 65 or March 1965. Minor dents in tanks top and bottom, side straps are from a different radiator. Still Ford though. Side tank strap stamped C7ZE-8005-S1, with a date of 7EC. Kind of Frankensteined together to fit a 1967 Mercury Cougar or Mustang. The makings of two separate radiators. Core grade, will need a new core. 

Four needed per fan shroud. While not technically correct, some like the black screws over the silver because it better matches the radiator and shroud. Hexwasher Head #14 X 5/8 Tapping Screw Ford Part Number: 31498-S

This kit has everything you need to repair your clutch and brake pedal and pedal support in one easy kit.Repairs 1967-70 Mercury Cougar or 1965-70 Ford Mustang. *Hint - All 1967-70 brake pedal hangers have the clutch pedal shaft bushings, even the automatic cars. The originals are swedged in. * Does not fit 1971-73 Mercury Cougar or Ford Mustang.

New metal clips to replace your worn out original fuse holders.

This great little kit replaces stock Ford bushings that can wear out in as quick as one year. This is a very simple repair and upgrade, once you have removed the pedal support from the car. Upon completion of this you will be rewarded with greatly reduced pedal pressure and the knowledge that you will never have to replace these bushings again. This is a must have for anyone with a manual transmission.Does not fit 1971-73 Mercury Cougar or Ford Mustang.

Used OEM Ford heater blower motor resistor that attaches to the heater blower fiberglass housing. We inspect these for damage or broken wires and we guarantee these will make your fan work. Not only was this heat resistor was factory installed on 1967-68 Mercury Cougar and 1965-68 Ford Mustang.Ford part # C2OA-18591-A or C8ZZ-18591-A*Note - Excludes Heater with integral or factory air conditioning.

Push on retainer for rear drum brakes. 2 or 3 of these were used to hold the rear brake drums onto the rear axle assembly during construction of your 1967-73 Mercury Cougar or 1965 - 73 Ford Mustang. While not necessary, these are a neat concours item. Sold individually.  Ford part number 372188-S

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

Permatex RTV gasket maker for the automatic transmission in your Mercury or Ford. Great stuff for sealing up that leaky transmission pan gasket!

New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.

Original style fuel tank installation screw. 3/8 inch hex head. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks. See item 11942 for the kit of 12 screws, better value.

Original style fuel tank installation screw kit. 3/8 inch hex head. This is a set of 12 new screws. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks.

Individual screw for attaching the headlight retaining ring on any 1967-70 Mercury Cougar or 1965-70 Ford Mustang, and pretty much most all other Fords during those years. #8 stainless steel screw. Two needed per headlight bulb retaining ring. A total of 8 would be needed for a quad headlight system on all Cougars.Replaces Ford part number 375452-S.

Oil seal for rear axle on any 1967-73 Mercury Cougar or Most Ford cars with 28 spline axles. Most all Cougar and Mustang received 28 splined axles, whether they have an 8 inch or nine inch rear end from the factory. Seal measurements: 1-3/8 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-B.

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...