1965 Ford Mustang

New Old Stock vacuum advance. This style used 1972 on Motorcraft 351-4V V-8 distributors. DD-339 and code 348 numbers associated with this unit. This is an MOTORCRAFT marked vacuum advance. Brass nipple not included, but is needed. Instructions for installation with this one too. Application is for Q code 351CJ distributors marked D2ZF-12127-GA, D2ZF-12127-GB, D2ZF-12127-GC, D2ZF-12127-HA, and D2ZF-12127-HB. Ford Part Number D2ZZ-12370-A ...

New Old Stock vacuum advance. This style used 1968-69 on Autolite V-8 distributors. A12 and DD-236 numbers associated with this unit. This is an Autolite marked vacuum advance Threaded cap and spring not included Ford Part Number C8AZ-12370-A

New Old Stock vacuum advance. This style used 1965-67 on Autolite V-8 distributors. Designed for use with a threaded nipple. DD-190 and code 303 numbers associated with this unit. This is an Autolite marked vacuum advance, there are other service replacement units marked MOTORCRAFT. Threaded nipple available separately. Ford Part Number C5AZ-12370-A

New Old Stock vacuum advance. This style used 1965-67 on Autolite V-8 distributors. Designed for use with a threaded nipple. DD-190 and code 303 numbers associated with this unit. This is an MOTORCRAFT marked vacuum advance, there are other service replacement units marked Autolite. Threaded nipple available separately. Ford Part Number C5AZ-12370-A

NOS distributor lead wire without the boot for the coil. There were at least two different lengths of wire leads found on 1967 Mercury Cougar and most all other Ford and Mercury distributors. This is the longer wiring harness, about 20 inches outside of the distributor. Direct replacement for 1961-67 Ford distributors.Ford part number C1VF-12216-A.

Reproduction distributor lead wire without the boot for the coil. There were at least two different lengths of wire leads found on 1967 Mercury Cougar and most all other Ford and Mercury distributors. This is the longer wiring harness, about 20 inches outside of the distributor. Direct replacement for 1961-67 Ford distributors.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

Used driver side (left hand) grade "A" clear vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. It will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. This vent window glass often comes with a frame and...

Used driver side (left hand) grade "B" clear vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. It will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with some scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part # C5ZZ-6521413-C. *NOTE* Air conditioning cars were...

Reproduction driver side (left hand) clear door vent glass for the Mercury Cougar or Ford Mustang. There are three versions of this piece of glass. The clear version is just that, clear. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked version is not a tint option that...

Reproduction Passenger side (right hand) clear door vent glass for the Mercury Cougar or Ford Mustang. There are three versions of this piece of glass. The clear version is just that, clear. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked version is not a tint option...

Used grade "A" clear passenger side (right hand) door vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. It will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part # C5ZZ-6521412-C. *NOTE* Air...

Used grade "B" clear passenger side (right hand) door vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. It will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part # C5ZZ-6521412-C. *NOTE* Air conditioning cars...

Used driver side (left hand) grade "A" green tinted vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. All Cougars or Mustangs came with this SUN-X tinted glass if they were factory equipped with A/C. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Ford part #...

Used driver side (left hand) grade "B" green tinted vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. All Cougars or Mustangs came with this SUN-X tinted glass if they were factory equipped with A/C. Good used door glass with some scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Ford part # C5ZZ-6521413-D.Check...

Used grade "A" tinted passenger side (right hand) door vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. All Cougars and Mustangs came with this green tinted SUN-X glass if they were also equipped with A/C from the factory. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro....

Used grade "B" tinted passenger side (right hand) door vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. All Cougars and Mustangs came with this green tinted SUN-X glass if they were also equipped with A/C from the factory. Good used door glass with a few scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than...

This Upper Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73.Replaces Ford part #: C7OZ-3105-B.*Installation tip - The inside diameter of the grommet is just a hair too small to properly fit on the stud. Restoration expert and MCA Judge Marcus Anghel, suggests using a slightly larger round punch to open the hole slightly. If the boot isn't seated low enough, the boot will tear and fail in short order.

Fuel pump drive eccentric for most small block Ford engines 1963-72. Including 221, 260, 289, 302, and 351W. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 2-1/2 inches in diameter.Ford part number C3AZ-6287-B.

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

New 1-1/4 inch expansion plug. Expansion plugs were used as dust covers on the wide bearing style air conditioning pulleys commonly used on Ford cars 1965-68. These are not a real tight fit in those pulleys. Best to still install to keep dust out, we recommend using a bit of JB Weld to hold them.

Fan spacer, measuring 2-7/8 inches, sometimes mentioned as 3.15" overall. Applications include 1967-68 Mercury Cougar and Ford Mustang with 289/302 and standard cooling. Reference number YA-79.Ford part # C5OE-8546-A, Ford engineering # C5OZ-8546-A.

Fan spacer, measuring 3-1/16 inches, sometimes mentioned as 3.40" overall. Applications include 1967 Mercury Cougar and Ford Mustang with 289-4V. Reference number YA-78.Ford part # C5AE-8546-B, Ford engineering # C5AZ-8546-B.

Oil filter adapter for all Ford small block engines including 221, 260, 289, 289HiPo, 302, and 351W engines. Ford indicates that this was used 1962-1970. Screws into the engine block. We do not know the threads, but the small side is standard oil filter sized.Ford part number C2OZ-6882-C.

New fluorescent needle restoration paint for the gauges in your Mercury Cougar or Ford Mustang. Over the years, the sun has wreaked havoc on your Cat or Pony. This sun damage has also had it's way with the needles on you gauges and washed them out. This true fluorescent paint will not only make your needles look factory fresh, but will also bring back their glow at night. One jar contains 2.25ml worth of paint.

This is a much cheaper version of the foil sound deadeners and underlays we sell. This particular insulation is basically bubble wrap with two layers of foil on both sides. Good for insulating headliners, floor pans, trunk areas, door panels, kick panels and just about anything else you might want to use it for. This insulation comes in a 48" X 72" roll. Just grab a pair of scissors and cut your shapes. You can use any adhesive you like (contact cement or weatherstrip adhesive,...

This USB flash drive contains the electronic collection of the 64 - 71 Ford Car and Truck Technical Service Bulletins (TSB) released from October 19th 1964 through September 10th 1971. Technical service bulletins are official communications between Ford and their dealerships that describe processes for troubleshooting or fixing certain common problems. TSB's document recommended procedures for repairing vehicles, when there are several occurrences of an unanticipated problem. TSB's can range...

Reproduction pair of frame rail / floor supports. These extend off the back of the front frame rail and give support under the front floor pan. Includes driver and passenger sides.

Brass and steel freeze plug or expansion plug set for any Ford 289 / 302 / 351W engine. 1967-70 Mercury Cougar and 1967-73 Ford Mustang. 15 piece set with threaded screw in plugs as shown. 

Front Parking Light To Valance Pads are sold as a pair. Fits the 67 and 68 Cougar or 65 and 66 Mustang. Replaces Ford part #: C5ZZ-13217.

***WARNING*** Plugging these directly into a Cougar wiring harness without correctly re-wiring in the pigtails may fry your wiring harness! Reproduction driver side (left hand) and passenger side (right hand) front turn signal / parking light assemblies for the Ford Mustang. The plug is not correct for the Mercury Cougar's wiring harness and will need to be changed to work properly. However, this is an easy straightforward process which we lay out below. Plus you can save a good amount of that...

This is a single plug (standard models without low fuel warning light) fuel sending unit with an extra bung for a return line for 1967-68 Cougars and Mustangs running fuel injection. No need to change the whole tank in order to upgrade your car to fuel injection!  Main line 3/8" Return line 1/4" Check out the video below on our new gauge tester: ...

Made from fuel resistant cork like original.  Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt, that in both Dearborn and San Jose, the factory workers did not use the pre-drilled holes when installing the fuel filler necks. We have suggested that the supplier not make them with holes. Probably...

NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...

Used Heater Box Assembly for 1967-1968 Mercury Cougar and 1965-68 Ford Mustang without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a used factory fiberglass two piece heater box/heater core casing. We suggest purchasing the foam kit and new heater core. These used boxes are over 45 years old, there will likely be some cosmetic issues, which include minor cracks or chipped fiberglass. Clips to hold two pieces together are included. *Note...

A modern touch to this classic muscle car look. This kit is the same Scott Drake "Shelby Style" Billet hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, machined billet aluminum top plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are Machined billet aluminum top plates and the deluxe is stainless steel. Common...

This kit is the same Scott Drake "Shelby Style" hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the exact location varied from...

Reproduction brackets to hold the junction of the steel brake line and the rubber brake hose. Mounts to the frame rail. Fits 1967 Mercury Cougar and 1965 - 1967 Ford Mustang with factory installed Kelsey Hayes 4 puck disc brakes only. These are manufactured 30 thousandths thicker to compensate for the missing flange that the originals had along the sides.  Replaces Ford part numbers C5ZZ-2082-D and C5ZZ-2082-C

The POGO Stick works just like the larger Hustler stick but is much easier to ship. If you need more leverage you can just add a pipe for leverage. We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Check out our video below: ...

Used driver side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired.  Ford part number C4ZB-7650535-C.

Used passenger side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired. Ford part number C4ZB-7650534-C.

Reproduction 15 x 7 aluminum alloy wheel designed to look like the styled steel wheels that were optional in 1967 - 1970. Mercury was looking to make a wheel similar to the Cragar and Appliance brand after-market wheels available at the time so these will resemble era correct wheels on any Ford or Mopar product utilizing the 5 on 4 1/2 lug pattern. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction 17 x 8 aluminum alloy wheel designed to look like the styled steel wheels that were optional in 1967 - 1970. Mercury was looking to make a wheel similar to the Cragar and Appliance brand after-market wheels available at the time so these will resemble era correct wheels on any Ford or Mopar product utilizing the 5 on 4 1/2 lug pattern. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

These T/A style wheels have the classic 8-spoke European design that was popular with road racers in the 60's and 70's. Fits the 60-73 Mustang, Falcon, Fairlane, Comet and 67 - 70 Cougar. Chrome plated plastic Legendary Wheel hubcap included. Back spacing on all Legendary wheels is 4 1/4". Bolt pattern 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. Check out our video on Legendary Wheels below: ...

Reproduction amber parking light / turn signal lens. This was actually used on the 64 - 66 Mustang which used the amber lens and clear bulb, as compared to the 67 - 68 Cougar which used the clear lens and amber bulb. Sold without gaskets or hardware (see related items).Sold individually

These plates were really clean before they were sent out for restoration, you can get  your Oregon plates restored at http://oregonplates.com/NOTE: The plates and plate numbers pictured are exactly what you'll receive.

Used wheel cylinder link pin. This pin protrudes from both ends of the wheel cylinder and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Fits all drum brake wheel cylinders, front or rear drum brake systems. Two needed per wheel cylinder. Sold individuallyFord part number B7A-2042-A.

This version with a cast head was only found in the earliest 1967 Mercury Cougars. 13/16 inch socket. Much better quality than the later stamped steel version.