Smog / Thermactor Emissions Systems & Related Parts

Application is 1967 - 1968 289/302 and 1969 Boss 302 Eliminator alternator adjusting with factory air injection emissions. Casting number C6OE-10145-A, Ford part number C6OZ-10145-A.

Application is 1967 390 with California emissions. Casting number C6AE-10145-A. Ford part number C6AZ-10145-A.

Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines. This is also referred to as the low mount alternator adjusting bracket. It has the Ford stamped casting number of C8AE-10145-B. Ford part number is C8AZ-10145-B.

C8AE-9B452-B Thermactor smog pump belt tensioning adjustment bracket. Application is for all 1968 - 1970 FE engines with factory installed thermactor smog systems.

Reproduction thermactor smog pump adjusting bracket for all 1968 Mercury Cougar and 1968 Ford Mustang with S code 390-4V engines. Additionally this bracket was also used on 1968-70 Mercury Cougar and Ford Mustang with 428 Cobra Jet engines. Quality made product. Ford number C8AE-9B452-B.

Reproduction thermactor smog pump adjusting bracket for all 1970 Mercury Cougar Eliminator and 1970 Ford Mustang with Boss 302 engines. Quality made product. Replaces Ford part number D0ZE-9B452-A. We also have one copy of an earlier reproduction version without the stamped  D0ZE-9B452-A, on the part. Call 503-436-1130, will be sold at a good discount, just ask.

Cast iron bracket, must be used with the low mount 1967 alternator bracket. Casting # C6AE-9B463-BSee Illustration for 1967 390 Thermactor System. Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and belt alignment are the same. Click on images to enlarge.                        ...

1967 application only and only for the California emissions 289 engines. Uses 4 bolts to mount the drive pulley and has two air ports on the reverse side. Ford part number C7AZ-9A486-B. *Consider these used pumps as cores. We cannot warranty these pumps to work like new.

California emissions 390 engines only. Uses 4 bolts for mounting the drive pulley, the 390 pump has three air ports on the reverse side. Ford part number C6AZ-9A486-E. *Consider these used pumps as cores. We cannot warranty these pumps to work like new.

Common air pump for all 1968 - 1970 thermactor emissions systems. 1968 289-2V, 302-2V, and 302-4V all with manual transmissions, and 1968 390-4V, 427-4V all domestic US Cougars. Additionally all 1968 - 1970 428 Cobra Jets, and 1969 - 1970 Boss 302 Eliminators. Identified by the use of 3 attaching bolts for the drive pulley, a white colored cooling fan, and a round pressure relief valve on the side of the pump. Later pumps do not have this pressure relief valve. Good used thermactor smog air...

Nice American made reproduction bracket. Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines, all with Thermactor smog pumps. This is also referred to as the low mount alternator mounting bracket. It has the Ford stamped casting number of C8AE-10156-A. Ford engineering number is C8AZ-10156-A.

Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines. This is also referred to as the low mount alternator mounting bracket. It has the Ford stamped casting number of C8AE-10156-A. Ford engineering number is C8AZ-10156-A.

289 engines without factory air conditioning.

B1967 California emissions low mount alternator bracket for the S code 390-4V engine. Ford casting number C6AE-10156-A, Ford part number C6AZ-10156-A. The early bracket has two extra (for unknown reasons) small holes. Notice this late bracket can be found with both styles of FoMoCo logos.Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and...

Screws onto the cylinder head smog tubes. Sold individually, two needed per application. Ford part number C8AZ-9A487-A.New old stock Ford.

Screws onto the cylinder head smog tubes. All California emissions 1967 Cougars with 289 or 390 engines, and 1969 - 1970 Boss 302 Eliminators, all thermactor smog air tubes. Sold individually, two needed per application. Due to the difficulty in removing these valves, we sell them attached to the air supply tubes. These are aftermarket replacements and will look significantly different than the OEM factory installed valves. But they work.

Screws onto the cylinder head smog tubes. All California emissions 1967 Cougars with 289 or 390 engines, and 1969 - 1970 Boss 302 Eliminators. Sold individually, two needed per application. Due to the difficulty in removing these valves, we sell them attached to the air supply tubes. See 1967 cylinder head smog tubes.

All 1967 289 Cougars with California emissions. Hose that connects from the air inlet assemble to the air pump. Molded hose, thicker in diameter than the other connecting rubber hoses. Inside diameter is about 1 inch. Kind of shaped like a "J". Fits C and A code 289 engines, 1967 Mercury Cougar and 1966-67 Ford Mustang and others. Hose only, no wire spring clamps, included. Ford part number C6OE-9B458-B.

New old stock, special molded California emissions rubber hose. Connects to the anti backfire valve, not sure where the other end attaches. About 12 inches long. Fits 1967 Mercury Cougar and Comet, and Ford Mustang and Fairlane, all with 390 thermactor smog.Ford part number C7OZ-9H534-B.

Used smog hose. Connects the smog pump to the check valve. 1967 Mercury Cougar and 1967 Ford Mustang with C and A code 289 engines, and typical California Thermactor smog system. Hose only, no clamps included. Hose is about 30 inches long with a 90 degree bend. Inside diameter is 3/4 inch. Ford part number C6OE-9H548-F.

Used smog hose. Connects the metal "T" connector to the check valve. 1967 Mercury Cougar and 1967 Ford Mustang with C and A code 289 engines, and typical California Thermactor smog system. Hose only, no clamps included. Hose is about 19 inches long with a 90 degree bend. Inside diameter is 3/4 inch. Ford part number C7OE-9H534-A.

Bolt that goes through the air pump mounting bracket. Pump rotates on this bolt. Bolt size 3/8"-16 x 4.50" long.

Bolt that goes through the air pump mounting bracket, effectively hanging the alternator down low. Alternator rotates on this bolt. Bolt size 7/16"-14 x 3.75" long.

C5TE-10156-A Alternator mounting bracket for most 1967 Mercury Cougar and Ford Mustang with 390 engine. Ford master part number C5TZ-10156-A. *Note - Excludes cars with California DSO's with smog pump.

Cast iron in construction, there are two slightly different brackets for 1967. This part has a casting number of C7OE-9B450-A. This would be the early bracket for Cougars built prior to 1/3/1967. Must be used with the 1967 style air pump C7AZ-9A486-B. Ford air pump mounting bracket part number C7OZ-9B450-A. *Emissions equipment came on all 1967 Ford and Mercury cars. California DSO's only.

Cast iron in construction, casting number C7OE-9B450-B there are two slightly different brackets for 1967. This would be the later bracket for Cougars built after 1/3/1967. Must be used with the 1967 style air pump C7AZ-9A486-B. *Emissions equipment came on all 1967 Ford and Mercury cars. California DSO's only. Ford air pump mounting bracket part number C7OZ-9B450-B

Cast iron construction similar to the 1967 bracket but made to fit the 1968-1970 style smog pump with 3 bolt pulleys. Ford part number C8AZ-9B450-B, casting number C8OE-9B450-A. Mounting hardware sold separate.

Reproduction thermactor smog anti-backfire valve canister mounting bracket. For all 1968 390GT engines, GT-E 427-4V engines, and 1968-70 428 Cobra Jet engines. Painted Ford engine blue a shown. Nice reproduction, made in the USAFord part # C8AE-9C486-A.

Thermactor smog anti-backfire valve canister mounting bracket. For all 1968 390GT engines, GT-E 427-4V engines, and 1968-70 428 Cobra Jet engines. Ford part # C8AE-9C486-A. *RESTORATION TIP* This bracket was painted Ford Engine blue from the factory.

C5AZ-10A370-C Alternator mounting spacer, goes between the cylinder head and alternator housing. Fits 1968-70 390-2V, 390-4V, and 428CJ engines. Smog OK. There is no casting number but one is listed C5AE-10A370-C. Inside diameter 7/16". We measure them out at 1-5/8 inches long, supposed to be pink anodized or tinted.

Steel spacer between cylinder head and pump. Inside diameter 3/8", length approximately 1-13/16".

Application is 1968 289-2V, 302-2V, and 302-4V all with manual transmissions. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut/ one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube. New Old StockFord part number C8OZ-9B471-A.

Application is 1968 289-2V, 302-2V, and 302-4V all with manual transmissions. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut/ one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

Application 289-4V auto and 289-2V manual transmissions at the beginning of the 1967 model year. Pulley diameter 4 inches, 1967 smog pulleys are unique in that they have 4 mounting holes. Ford part number C6OZ-9B447-A and engineering number is C6OE-9B447-A or B. *California DSO 52 and DSO 53 only.

1967 289-2V after 11/14/1966 without air conditioning. Pulley diameter is 4.75 inches, 1967 smog pulleys are unique in that they have 4 mounting holes. Ford part number C7AZ-9B447-E. *California DSO 52 and DSO 53 only.

Application 289-2V (C code engines) prior to 11/14/1966, 289-4V (A code engines) all without air conditioning. Pulley diameter 3.97 inches, 1967 smog pulleys are unique in that they have 4 mounting holes. Ford part number C7AZ-9B447-A and engineering number is C7ZE-9B447-A. *California DSO 52 and DSO 53 only.

Application all 390-4V engines with and without air conditioning. 289-2V and 289-4V all with air conditioning. Pulley diameter is 5.95 inches 1967 smog pulleys are unique in that they have 4 mounting holes. Ford part number C6AZ-9B447-E, engineering number as seen on the front of the pulley is C6AE-9B447-E. *California DSO 52 and DSO 53 only.

1968 390-4V (S code engine) smog pump pulley with air conditioning, manual and automatic transmissions. 3 bolt smog pump pulley with a diameter of 4.98" inches. Ford part number C8OZ-9B447-B. Casting number C8OE-9C480-B.

Application 1968 - 289-2V, 302-2V, 302-4V, all with manual transmissions and without air conditioning. Also 1968 390-4V and 1968 - 1970 428CJ, all without air conditioning. Pulley diameter 4.75" inches. Ford part number is C8AZ-9B447-B and the engineering number as seen on the front of the pulley is C8AE-9C480-A.

Used driver side smog hose. Connects the cylinder head smog tube check valve to the distribution "T" connector. 1967 Mercury Cougar and 1967 Ford Mustang with C and A code 289 engines, and typical California Thermactor smog system. Hose only, no clamps included. Ford part number C7OE-9C433-A.

Used passenger side smog hose. Connects the cylinder head smog tube check valve to the distribution "T" connector. 1967 Mercury Cougar and 1967 Ford Mustang with C and A code 289 engines, and typical California Thermactor smog system.  Ford part number C6AE-9B459-A.

Thermactor smog hose installation clamps. Fits all Ford and Mercury 1968 S code 390-4V or W code 427-4V engines sold in the US. Additionally fits 1968-70 428 Cobra Jet and Super Cobra Jet engines. Set of clamps, several bolts and spacer as shown. Include bolts for pump pulley, top bolt on pump for adjusting bracket, and pivot bolt and spacer for pump.

Reproduction hardware kit for installing the smog pump on cars with 390 / 427 / 428CJ engines from 1968-70. Including Cougar, Mustang, Torino, Ranchero, Cyclone, etc. Includes spacer, pivot bolt and washer, adjusting bracket bolts.

Complete original system as taken from a small block 289 from California. Comes with all items shown and you can choose from the large pulley as found on AC cars or the smaller pulley found on non AC cars. These systems are getting rather elusive to find with pliable hoses, correct Wittek clamps and correct fasteners. For years only those with big block cars cared to obtain original smog systems. That has changed... Even if you do not install it, if your car originally had it it will...

Set of thermactor smog tubes on any 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original 390 or 428CJ cylinder heads drilled for air injection smog system from factory. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the ferrules / nuts and other hardware.

Used smog hose "T" connector. Connects the cylinder head smog tube hoses and hose to check valve. 1967 Mercury Cougar and 1967 Ford Mustang with 289 or 390 engines, and typical California Thermactor smog system. The 1967 Engine assembly manual states that this part has a number of: 379179-S, while in fact it is imprinted with 379169-S. Ford part number 379179-S, 379169-S.

Thermactor smog tube installation ferrules. Set of 8 nuts and barrel shaped ferrules.Fits: 1968 Ford and Mercury S code 390-4V engines sold in the US.1968 Ford and Mercury W code 427-4V engines sold in the US. 1968 / 1969 / 1970 428 Cobra Jet engines.1968 / 1969 / 1970 428 Super Cobra Jet engines. ...

Three piece Thermactor Smog hose set; moulded, striped, and stamped like original factory installed hoses. The 1968 ink stamped was likely used partially into 1969. We also list hoses with the C9... stamps.Fits: 1968 Ford and Mercury S code 390-4V engines sold in the US.1968 Ford and Mercury W code 427-4V engines sold in the US1968 / 1969 428 Cobra Jet engines. 1968 / 1969 428 Super Cobra Jet engines. ...