1967 Mercury Cougar / Ford Mustang 390 Thermactor Smog Components

Application is 1967 390 with California emissions. Casting number C6AE-10145-A. Ford part number C6AZ-10145-A.

Cast iron bracket, must be used with the low mount 1967 alternator bracket. Casting # C6AE-9B463-BSee Illustration for 1967 390 Thermactor System. Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and belt alignment are the same. Click on images to enlarge.                        ...

California emissions 390 engines only. Uses 4 bolts for mounting the drive pulley, the 390 pump has three air ports on the reverse side. Ford part number C6AZ-9A486-E. *Consider these used pumps as cores. We cannot warranty these pumps to work like new.

B1967 California emissions low mount alternator bracket for the S code 390-4V engine. Ford casting number C6AE-10156-A, Ford part number C6AZ-10156-A. The early bracket has two extra (for unknown reasons) small holes. Notice this late bracket can be found with both styles of FoMoCo logos.Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and...

Screws onto the cylinder head smog tubes. All California emissions 1967 Cougars with 289 or 390 engines, and 1969 - 1970 Boss 302 Eliminators, all thermactor smog air tubes. Sold individually, two needed per application. Due to the difficulty in removing these valves, we sell them attached to the air supply tubes. These are aftermarket replacements and will look significantly different than the OEM factory installed valves. But they work.

Screws onto the cylinder head smog tubes. All California emissions 1967 Cougars with 289 or 390 engines, and 1969 - 1970 Boss 302 Eliminators. Sold individually, two needed per application. Due to the difficulty in removing these valves, we sell them attached to the air supply tubes. See 1967 cylinder head smog tubes.

Set of nuts and Ferrules for thermactor smog tubes on any 1967 S code 390, 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original or reproduction smog tubes. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the smog tubes and other hardware.

New old stock, special molded California emissions rubber hose. Connects to the anti backfire valve, not sure where the other end attaches. About 12 inches long. Fits 1967 Mercury Cougar and Comet, and Ford Mustang and Fairlane, all with 390 thermactor smog.Ford part number C7OZ-9H534-B.

Application 1967 289 and 390 thermactor California emissions fresh air inlet assembly or Air pump filter assembly. *Note - Excludes HiPo, or K code 289 engines for 1967. Ford part # C7AF-9A492-A

Application all 390-4V engines with and without air conditioning. 289-2V and 289-4V all with air conditioning. Pulley diameter is 5.95 inches 1967 smog pulleys are unique in that they have 4 mounting holes. Ford part number C6AZ-9B447-E, engineering number as seen on the front of the pulley is C6AE-9B447-E. *California DSO 52 and DSO 53 only.

Thermactor smog hose installation clamps. Fits all Ford and Mercury 1968 S code 390-4V or W code 427-4V engines sold in the US. Additionally fits 1968-70 428 Cobra Jet and Super Cobra Jet engines. Set of clamps, several bolts and spacer as shown. Include bolts for pump pulley, top bolt on pump for adjusting bracket, and pivot bolt and spacer for pump.

Set of thermactor smog tubes on any 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original 390 or 428CJ cylinder heads drilled for air injection smog system from factory. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the ferrules / nuts and other hardware.

Mounts on the rear of the intake manifold, it must be a 1967 or possibly a 1966 "S" intake manifold. There are no mounting provisions on 1968 or later factory cast iron intake manifolds. This valve has two equal sized vacuum hose fittings in addition to the steel line going to an intake manifold vacuum source. Due to the age of these valves, we cannot guarantee that they will work. Consider this valve non-functional. Ford part number C6AE-E or C6AZ-9B289-C. 1967 California emissions only. ...

1967 390 smog pump adjusting arm, casting number C7AE-9B452-A. Ford part number C6AZ-9B452-C. Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and belt alignment are the same. Click on images to enlarge.                                       The...

Application - 1967 Mercury Cougar and Ford Mustang with 390 engines.  Might be two versions, this one would be the mid or late version. There are references that this bracket was also used on 289 engines with air conditioning, but that may not be consistent through out the year, if it all. Maybe early 1967 cars with A/C. Ford part number stamped C7AE-9B453-A.

Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder.Thread pitch 1/2" x 20 *Note - Export cars that did not require smog had a much shorter version of this plug installed at the factory. The plug shown here would be...

These were installed at the factory on 390 / 427 / 428 equipped cars that were exported to countries that did not require the smog system. They are much shorter than the over the Ford counter service plugs you see in the states that are put on after one removes the smog system.

All 1967 390 Cougars with California emissions. Special molded hose see diagram. Connects the smog pump and air inlet assembly.

Bolt that goes through the air pump mounting bracket. Pump rotates on this bolt. Bolt size 3/8"-16 x 4.25" long.

C5TE-10156-A Alternator mounting bracket for most 1967 Mercury Cougar and Ford Mustang with 390 engine. Ford master part number C5TZ-10156-A. *Note - Excludes cars with California DSO's with smog pump.

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.

Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C