Seat Belt Hardware

Used in multiple applications front and rear lap belts. Inner and outer, marked with a letter "B" in at least three known fonts. 1-3/4 inches long, 1/2 inch shoulder, Torx 50 tool for installation and removal.

Used on inner and outer rear seat belt bolts, four per car in 1970 -1971 and used only on the inner rears in 72 - 73 due to the addition of rear retractors. Used in conjunction with two red washer / spacers, marked with three known font styles of the letter "A". 1-5/16 inches long, Torx 50 is the tool for installing and removing.

Two per car, identified with the letter "D" in three known fonts. This bolt was used in conjunction with a chrome spacer / washer that is also marked with the letter "D". 1-1/2 inches long, 1/4 inch shoulder, use a Torx 50 for installation and removal.

Replaces Ford Part # 382626-S Sold individually

Concours correct for 67, but a nice dress-up item for 68-73. Replaces Ford Part # 382627 Four bolts, four washers and eight rubber washers in mounting kit.

Reproduction bolts and washers for the shoulder belts on any 1969-73 Mercury Cougar or Ford Mustang. Includes 2 each of the "D" bolts and chrome thick washers. Quality AMK kit F-3563.

We will make sure these original seat belt bolts are damage free. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! *NOTE* Pictured is a complete set of 1969 Torx bolts, spacers, and washers for a coupe. May also have some minimal surface rust.

Used bolts, and usually new washers. Convertible kit comes with 4 - "A" bolts, 4 "B" bolts, 10 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang convertibles. Coupes or hard tops would include shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us...

We will make sure these original seat belt bolts are damage free and rust free. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! 503-463-1130*NOTE* Pictured is a complete set of 1969 Torx bolts, spacers and washers for a coupe.

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 4 total per car, all 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped for the front seat belts inboard on 1971-73 cars. Round anchor bracket with factory welded nut for added strength. See related items for good used seat belt anchor plates if you have concours needs. Replaces Ford Part # D1AZ-6561216-A. ...

Reproduction set of front seat belt bolts for your 69 - 70 Cougar or Mustang. Included are the 4 bolts, 4 large washers and 4 anti rattle gaskets.

Fits 1968 Standard or XR7

Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.

One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.