Interior Fasteners

This is a used A/C center vent attaching clip. Two required per center AC vent, the two tiny tabs fit in the holes on the sides of the vent assembly and when you tighten the Phillips screw it will pull the vent tight against the dash pad. Very hard to come by, others have used silicone to bond the chrome vent in place when clips could not be found.Replaces Ford part number C7AZ-14570-A.

New screw with a correct 3/8 inch hex head for installing all armrests for all years.

Used on inner and outer rear seat belt bolts, four per car in 1970 -1971 and used only on the inner rears in 72 - 73 due to the addition of rear retractors. Used in conjunction with two red washer / spacers, marked with three known font styles of the letter "A".

Used in multiple applications front and rear lap belts. Inner and outer, marked with a letter "B" in at least three known fonts.

Replaces Ford Part # 382626-S Sold individually

Two per car, identified with the letter "D" in three known fonts. This bolt was used in conjunction with a chrome spacer / washer that is also marked with the letter "D".

New single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. AMK part. Sold individually, Ford part number 57487-S.

Used single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. Sold individually, Ford part number 57487-S.

Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually. 

Concours correct for 67, but a nice dress-up item for 68-73. Replaces Ford Part # 382627 Four bolts, four washers and eight rubber washers in mounting kit.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per car for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per armrest for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

These original clips hold better than the reproductions we offer. If you look closely you will see the angle bend is more acute on the originals. For you 71-73 owners with warped panels you will want to use these original clips (at least along the bottom edge) for a tighter hold. The only difference between this spring clip and the other used one we offer is the presence of the foam spacer pad. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

These clips are found on the power window swtiches of the 69 - 70 Cougar. Each power window switch has one of these clips and one of the J hook clips. 6 small clips required per master switch panel, one for each window switch and two per lock out switch. 

These same clips are also found on the four rocker switches located in the center of the 1969-1970 XR7 dash pad. Do not bend the "J" shaped tab any further than is necessary to release the plug from the back of the switch as these break easily. There are 16 of these used on a Cougar with power windows in 1969, add the 8 in the dash of the XR7 Cougars and some cars have a total of 24.Replaces Ford part number C9AZ-14530.

These same clips are also found on the four rocker switches located in the center of the 1969-1970 XR7 dash pad. Do not bend the "J" shaped tab any further than is necessary to release the plug from the back of the switch as these break easily. There are 16 of these used on a Cougar with power windows in 1969, add the 8 in the dash of the XR7 Cougars and some cars have a total of 24.Replaces Ford part number C9AZ-14530.

New chrome finish screws for attaching OEM consoles. Screws fit all stock consoles 1967-73 on Mercury Cougar and Ford Mustang, most any Ford consoles actually. Phillips head oval. 1967-68 consoles use 4 attaching screws, 1969-70 consoles need 6 along the outside, 1971-73 consoles have a total of 8 screws along the outside. These are 1-1/2 inches long like the originals.

This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.

Bulk pack of 100 oval head phillips screws for door and window crank handles.

Holds insulation to the firewall. Sold individually, 6 per car. Replaces Ford part # C8ZZ-6501691.

Bolts, washers, and spacers kit for installing the rear bumper brackets on any 1969-70 Mercury Cougar or Ford Mustang.

We will make sure these original seat belt bolts are damage free. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! *NOTE* Pictured is a complete set of 1969 Torx bolts, spacers, and washers for a coupe. May also have some minimal surface rust.

We will make sure these original seat belt bolts are damage free. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! *NOTE* Pictured is a complete set of 1969 Torx bolts, spacers, and washers for a coupe. May also have some minimal surface rust.

We will make sure these original seat belt bolts are damage free and rust free. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! 503-463-1130*NOTE* Pictured is a complete set of 1969 Torx bolts, spacers and washers for a coupe.

We will make sure these original seat belt bolts are damage free and rust free. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! 503-463-1130*NOTE* Pictured is a complete set of 1969 Torx bolts, spacers, and washers for a coupe.

This kit contains 500 hog rings, more than enough for two bucket seats and one bench seat.

Reproduction installation kit for the 1969 Cougar dash pad.

Reproduction installation kit for the 1970 Cougar dash pad.

This specialty screw attaches the gas pedal to the throttle linkage. Fun fact: the head looks like Phillips (and that works fine) but this is actually designed for a Pozi bit.

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Correct rivets for use after you have painted your car or installed a new door. No special tools needed for installation. Simply lightly tap the center recessed portion with a small bolt or blunt punch. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com. Sold as a pair. Replaces Ford Part #: C5ZZ-6223000-A or 354921-S.

Sold individually Zinc with Bi-wax sealer (dark silver with gold color on threads)

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Sold individually. Two needed for globe box cable 1967-70 Mercury Cougar. 3 needed for installation of turn signal switches 1967-73 Mercury Cougar or Ford Mustang.Ford number 379203-S. Phosphate & Oil (gray-black)

One kit does both rear armrests for the XR7 or Standard interior coupe.

One size fits all.  Set of 4.  Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S

New set of 8 chrome headed screws for installing original or reproduction door speaker covers on all 1969-70 Mercury Cougars and Ford Mustangs.

1969-70 actually used a star head bolt but these are a much more user friendly screw that will work in its place. Sold in a set of four which is what you will need for one seat.

8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 4 total per car, all 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped for the front seat belts inboard on 1971-73 cars. Round anchor bracket with factory welded nut for added strength. See related items for good used seat belt anchor plates if you have concours needs. Replaces Ford Part # D1AZ-6561216-A. ...

Fits 1968 Standard or XR7