Fuel

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.

Made from fuel resistant cork like original.  Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt, that in both Dearborn and San Jose, the factory workers did not use the pre-drilled holes when installing the fuel filler necks. We have suggested that the supplier not make them with holes. Probably...

Replaces part #C0AF-9276-A. Goes between fuel sending unit and tank.

Reproduction two hole fuel line grommet for the Mercury Cougar or Ford Mustang.

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

This is the heat riser choke tube that provides heat to the choke, so the choke will open up as the motor warms up. Made out of Stainless Steel. This tube is designed to work on the 1970, 1971, 1972 & 1973 Mercury Cougar or Ford Mustang with a factory 2 Barrel Carburetor and the 351 Cleveland engine. Exact OEM standards and specifications. Correct fiberglass insulation, fittings and S clip.

This is a 2 piece heat riser choke tube that provides heat to the choke, so the choke will open up as the motor warms up.  Made out of OE Steel.  This tube is designed to work on the 1970, 1971, 1972 & 1973 Mercury Cougar or Ford Mustang with a factory 4 Barrel Carburetor and the 351 Cleveland engine.

This is a 2 piece heat riser choke tube that provides heat to the choke, so the choke will open up as the motor warms up. Made out of Stainless Steel. This tube is designed to work on the 1970, 1971, 1972 & 1973 Mercury Cougar or Ford Mustang with a factory 4 Barrel Carburetor and the 351 Cleveland engine.

Exact OEM standards and specifications.

Exact OEM standards and specifications for the 429 Cobra Jet / Quadrajet for the 1971 Mercury Cougar or Ford Mustang.

Exact OEM standards and specifications.

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

This part is installed on all XR7 fuel sending units and Cougars and Mustangs with the optional Convenience Control Package. Low quality off shore part that requires soldering to your fuel sending unit. This is a temperature sensing device that activates when the fuel level drops enough to expose the unit at which point the circuit is closed and the low fuel light comes on. Commonly referred to as a Thermister / Thermistor / Low Fuel Sending Unit.

Bracket mounts to top of stock cast iron Cleveland intake manifold, holding the throttle cable. Used on both the 351-2V and 351-4V engines with original Ford cast iron intake manifolds. There are two versions of this bracket per the MPC, it is such a minute detail, it is hardly worth listing separately.Replaces Ford part number D1ZZ-9728-E and D1AZ-9728-H.

Basic kit for rebuilding your Ford Autolite or Motorcraft square bore 4300 or 4 barrel carburetor. This kit is not for later spreadbore carburetors. Spreadbore carburetors have much larger secondary venturis. See picture.

Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. Your core must be complete and not overly corroded. We are unable to convert from non-low fuel to low fuel. We also cannot change plugs for different years. We do not repair rust or rust through holes. We do not have critical or specific spare parts for rebuilding....

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford sending units accepted. See our related listing for low fuel sending unit rebuilding. A quality...

Replaces Ford part #C0AZ-9A307-B.

Good used ring with only surface rust and no obvious gouges.

Used retaining ring for the fuel sending unit or vent on 1971 and newer tanks. Fits a little tighter than the reproduction rings. Ford part #C0AZ-9A307-B.

New replacement fuel filler neck screws for any 1971-73 Mercury Cougar or Ford Mustang. 5 needed per car, sold individually.

New replacement fuel filler neck screws for any 1971-73 Mercury Cougar or Ford Mustang. 5 needed per car, sold individually.

Mounts inside the trunk of both coupes and convertibles. Replaces Ford part # D1ZZ-9008.

Replaces Ford part # D1ZZ-9072. Special gas proof rubber seal that mounts in gas tank and filler pipe. Warning! If reproduction tank or filler pipe is not the same dimensions as originals the seal may leak, make sure and check for a good seal before putting into use.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with all 1971 Mercury Cougars and 1972 Cougar up until 6/19/1972. Accelerator cable attaches with a clevis pin.

Reproduction black Holley "Sniper" fuel injection conversion carburetor for the 67 - 73 Cougar or Mustang. Upgraded Sniper II also now available! Dual Pattern bolt on carburetor replacement, designed to fit 4150 Flange & Spread Bore manifolds - (Spread Bore Sealing Plate Part #9006 is recommended)Throttle body mounted ECU – no extra boxes to mountSupports up to 650hp with Four 100 Lb/Hr InjectorsOnly 4 Wiring Connections Required! (Battery +, Battery - , Switched Ignition & RPM)Includes...

The #1 EFI conversion system just got better! Introducing Sniper 2 EFI - a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. Holley took everything that they learned from the original Sniper EFI system and added 14 new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple...

Fuel tank spacer. Welds to the bottom side of the trunk pan. Spaces the tank, so that the fuel vapor separator assembly, isn't pinched. Easy to make these stands, and there are two needed, are approximately 1-1/2 inches tall. Strap is 1-1/8 inches wide.  

Replacement throttle pedal spring for your 71 - 73 Cougar or Mustang. Easy to replace, keeps correct tension on your gas pedal.

These are the straps that hold the gas tank in place. 2 required, sold individually.Replaces Ford part number D1ZZ-9092.

These are the straps that hold the gas tank in place. Sold as a pair.Replaces Ford part number D1ZZ-9092.

New strip caulk for the Mercury Cougar or Ford Mustang. These units come in one foot strips and are used for sealing the front fenders to top of aprons and for sealing the fuel tank flange to the trunk floor. They are also used for sealing the floor drain plugs, gas filler necks, door panel water shields, plus many other components that are fastened to the body. This box contains 60 individual strips of black non-hardening caulk.

This is the Left hand or driver side spring that holds the rear license plate or fuel door in the upright position. Fits all years of Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-B

This is the right hand or passenger side spring that holds the rear license plate or fuel door in the upright position. Fits 1967-68 and 1971-73 Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-A

Bracket that mounts to firewall for accelerator shaft. 1971-73 Mercury Cougar and Ford Mustang. 

Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine.Cable length 22.50 inches long.  *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.

Cable length 22.50 inches long. Has clevis and pin on the end for attaching to the throttle pedal assembly. *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.

Black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Ford part number: D1ZZ-9735 or D1ZZ-9735-A Stainless surround trim available too, part number D1ZZ-9735-B.

Over 100 total vacuum caps in 6 different sizes.

1971 351-2V Autolite 2100 Carburetor, manual transmission. D1OF-PA stamped on the carburetor base, 1.21" venturi size 351cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. Trivia - All 351-2V engines with manual transmission are 3 speeds. BTW, there were no 1971 4 speeds with H code 351-2V. Read about it in...

1971 351-2V Autolite 2100 Carburetor, manual transmission. D1OF-ZA stamped on the carburetor base, 1.21" venturi size 351cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1971 351-2V Autolite 2100 Carburetor, automatic FMX and C6 transmissions. D1OF-RA stamped on the carburetor base, 1.21" venturi size 351cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. *Note -with factory air conditioning.

1971 351-2V Autolite 2100 Carburetor, automatic FMX and C6 transmissions. D1ZF-SA stamped on the carburetor base, 1.21" venturi size 351cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. *Note -without factory air conditioning.

1971 351-4V Autolite 4300 Carburetor, 4 speed manual transmissions. D1OF-EA stamped on the carburetor base, 1.25" venturi size 605cfm. Rebuildable core carburetor with proper numbers. All linkages move freely.  We don't always have the factory Ford Autolite tag that was affixed to the top.

1971 351-4V Autolite 4300 Carburetor, automatic C6 transmission. D1OF-FA stamped on the carburetor base, 1.25" venturi size 605cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top.

1971 429CJ-4V Rochester Quadrajet Carburetor, automatic C6 and 4 speed transmissions. D0OF-B stamped on the carburetor tag only. 715 cfm. There are no Ford numbers stamped on this General Motors carburetor. Identified by large straight-in inlet fuel filter port of 7/8"-20 threads. Rebuildable core carburetor. *Note -with and without air conditioning. *Note -not for 429 Super Cobra Jet.

1971 429CJ-4V Rochester Quadrajet Carburetor, 4 speed transmission. D0OF-A stamped on the carburetor tag only. 715 cfm. There are no Ford numbers stamped on this General Motors carburetor. Identified by large straight-in inlet fuel filter port of 7/8"-20 threads. Rebuildable core carburetor. *Note -without air conditioning. *Note -not for 429 Super Cobra Jet.

1971 429CJ-4V Rochester Quadrajet Carburetor, automatic C6 transmission. D0OF-E would be stamped on the carburetor tag. 715 cfm. There are no Ford numbers stamped on this General Motors carburetor. Identified by large straight-in inlet fuel filter port of 7/8"-20 threads. Rebuildable core carburetor. Current carburetor has a date of 2539, which is Sept 10, 1969. No original tag for this item. Technically dated for a 1970 Torino and Cyclone, but the same as for 1971 Mercury Cougar and Ford...