Amazing quality that surpasses any NOS or restored emblem you will ever see. This unique emblem was only used on the front fender extension (driver side) of the 1967 and 1968 Cougar. Replaces Ford part number C7WY-16604-A. Here's some info on the measurements for placement: 1. From the bottom of the Y to the right edge of the deck lid - 1.28"2. From the top of the deck lid moulding to the bottom of the Y - 0.18"3. From the top of the deck lid moulding to the bottom of the M - 0.73" Also, note...

Used Driver Side / Right Side Fender Extension Emblem for the 1967 and 1968 Mercury Cougar

New Old Stock "G" and "T" 1967 Mercury Cougar and Ford Mustang individual fender letters. There were two ways that the cars were called out as GT's. Two individual letters and a single box with "GT" inside. These letters were also used on 1970-71 Mercury Cyclone. Both letters sold together. Ford part number C7ZZ-16098-A and C7ZZ-16098-B.

Found on the lower right corner of all 1971 - 1973 Cougars equipped with the XR7 Interior package. Both mounting studs will be in place and it will have a nice overall finish. Ford engineering number as seen on the backside is D1WB-65061A58-AA.

Reproduction center grille emblem background. This decal is only made with the "7", so you will need to remove the "X" and "R" from your existing decal and adhere them to this new one. You can clean those letters up with some extra fine polishing steel wool. The standard grill emblem with a walking cat uses the same stud configuration as XR7 so you can exchange emblems from one to another. ...

Our used center grill emblems will always have some amount of fade in the plexi area and if the backing has not separated from the rest of the emblem it often times will be lose. We have had good luck filling the backside with epoxy glue. The engineering number as seen from the rear is D1WB-8216-BB.Ford part number D1WY-8A223-B ...

This is a very nice reproduction that we have all needed for many years! You might want to buy a new Cougar walking cat emblem if you replace this background decal as it requires breaking the studs off your old emblem to get it off. Check out this video ...

These Mustang emblems have the incorrect pin placement for the 1968 Cougar so if you have original GT fenders you will have to drill new holes. Once mounted they look correct. Replaces the C7ZB... individual casting numbers. Licensed by FORD

This is a very nice reproduction of the 1973 XR7 hood or upper grille emblem. Replaces Mercury part # D3WY-16637-B. Simple to install, this emblem attaches using a clear silicone. Click on images to enlarge. Pictures below show this emblem installed on an original 1973 Cougar hood / grille center trim. ...

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

This emblem was located on either side of the quarter panel in 1968 and both front fenders in 1971 - 1973. The studs on the 71-73 were a little longer but this 1968 emblem is an excellent substitute. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very consistent. The plating is very inconsistent on the original Ford emblems. We are very excited to...

Correct anodized aluminum reproduction emblem for 1969-70 quarter panels. These high quality emblems have the black paint applied to the sides just as the originals did. If you want an emblem that better matches your front Cougar script you might want to consider these chrome emblems. You can reference the above pictures for correct dimensions, as taken from one of our cars using an original script emblem. Measurements are from the rear and lower body lines. *NOTE* This item includes the three...

Two required per car, right is the same as left. Good used Cougar emblem with no pits, deep scratches or broken studs.

Used COUGAR Script Quarter Panel Emblem for the 1969 and 1970 Mercury Cougar

Invest the big money elsewhere...Here is a NOS part we do not suggest paying the extra money for. These NOS emblems are not as good as the reproductions that cost less than half. The chrome is far superior, the studs stronger and the way they are assembled is much better on the reproductions. The type of person that buys these is doing a "very" original, concours restoration and will pay the extra money to avoid an "over-restored" appearance. These are sold singly only. Drive side part number...

These reproductions are fantastic quality! We sent NOS originals to Scott Drake to duplicate and they could not have done a better job. They come with the original type barrel clip fasteners and feature die cast frames with correct pin placement. These emblems are correct in every detail. We are really excited about these as it was said that they could never be done at a reasonable price without compromising quality. These are better than the $650-$750 NOS emblems you used to see occasionally...

Invest the big money elsewhere...Here is a NOS part we do not suggest paying the extra money for. These NOS emblems are not as good as the reproductions that cost less than half. The chrome is far superior, the studs stronger and the way they are assembled is much better on the reproductions. The type of person that buys these is doing a "very" original, concours restoration and will pay the extra money to avoid an "over-restored" appearance. These are sold singly only. Passenger side part...

This "Stick On" Cougar rear deck emblem was only used on models without the XR7 package. They are often missing as once the factory double sided tape dries out they are often lost forever. We also have a few very nice used examples in stock.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line...

High quality reproduction adhesive emblem for your deck lid. Measures 6.5" wide by 2.35" tall. It has the correct black paint applied to the sides. If you have a 71-73 Cougar this chrome emblem is a much better match to your other emblems even though it is not technically correct. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think...

Good used center with minor cracking, missing paint or maybe even a broken mounting tab. This was used on all 1969 Cougars with a three spoke wheel except the XR7.

Very rarely do we find one like this example that shows no sign of fading. This is for the person who is trying to achieve a very high level of preservation / restoration.

Good used center with no cracks and an average amount of fade most noticeable in the red portion of the emblem. Many of these emblems are broken or missing because people think this is the horn button and if they just push harder the horn will sound!

Reproduction center emblem for the 69 Cougar rim blow steering wheel.

The 1967 XR7 did not have rocker panel mouldings as did the 1968 - 1973 XR7 Cougars. All 1967 XR7 models came equipped with these "Hash" marks fastened to the rear of both rockers, at a rear tilting angle. Both sides received seven ribs, held by two Phillips screws each for a total of fourteen ribs in all. They were painted semi-gloss black in the recessed areas and the screws themselves were black as well. The leading ribs are usually pretty rough looking due to road debris wear, the one...

These always are peeling. Located on the right side on the dash face...

These were originally painted argent silver with the back ground painted semi-gloss black, they were not chromed. This emblem was used on all 1968 Cougar steering wheels with the exception of the XR7-G.

Good used emblem that is not warped and still has the silver paint intact. Don, Thought you might like to see another success story due to help from W.C.C.C. Attached is a picture of my 67 XR7, Lime Frost with Saddle interior. Thanks for all your help and advice. You and your team made a dream come true. Jim Kohler Check out this video

Excellent reproduction of the little 1 1/8" wide plastic emblem found on every 1970 - 1974 three spoke steering wheel pad. This emblem can also work on the 1969 - 1973 two spoke steering wheel pad but it is not an exact fit as the two spoke wheel emblem is only 1 1/32" wide. Keep in mind we made these EXACTLY as original so they are very fragile. If you happen to break the emblem anytime within three years of purchasing it we will sell you a replacement for half price when you submit the...

This small sized Cougar emblem (1 3/8" long) was used on 1969 - 1973 Cougars without AC. It was affixed to a block off plate in the very venter of the dash by two peened over die cast studs. It will glue back in place nicely and many Cougar fans have found fun "custom" applications for this attractive piece. This emblem will not be pitted or scratched in any way.

NOS "C" pillar emblem for your XR7. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Ford part number C7WY-6528818-B1

Since our restored emblems look so good we have a hard time selling NOS these days which works out just fine as we only seem to be able to obtain 1 of these every few years. Keep in mind your used cores have trade in value against this NOS part. Casting number seen on back side for the assembly is C9WB-65517A56-A and black plastic is C9WB-65517C00-A, Casting number on chrome is C9WB-65517A20-A

Good used "C" pillar emblem for your XR7 with no obvious pitting. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.Ford part number C7WY-6528818-B1 Hi Don: Thank you for fixing me up with the XR-7 pillar emblems. I appreciate doing business with you. It's nice doing business with guys who are not perfect, but try to be and correct anything within reason that is called to their attention. Take care, Greg Worth TN ...

Concours quality, perfect fit and a great value for the money. These little emblems are often the first thing one sees as they approach your car as they are at eye level. These emblems are located on the "C" pillars of your 67 - 68 Cougar but can also be used on a 71-76 Cougar with little or no modification. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Note that if you want to replace these emblems...

Poor chrome, for use as a core to be restored.

These are NOS Mercury Cougar XR7-G dash emblems. The version supplied these days from the OEM supplier do not have as definitive of cross hatch pattern and the edges are not as sharp. Another quick way to discern between NOS and new when original packaging is absent is to look at the back side. The backing for the two sided tape on the reproduction uses green vinyl and the originals used a green paper. The most disappointing difference between the new emblems and these NOS Ford supplied...

Assembly required This high quality corral fits perfectly and the chrome plating is well beyond what Ford originally did. The mounting studs are placed in the exact position as original. We have offered the walking cat and black background for sometime now but the challenge has been getting your used corral (or rectangle frame) remounted after you break off the studs to remove the assembly. Replacing this emblem assembly is probably (for the money) the best way to improve the looks of the...

Used core emblem that will need a new background decal. May have one or two hard to find small pits but will be above average even for a Western car. Make sure you consider our reproduction part before you purchase this. This used unit will be harder to install due to the fact that they were only designed to be installed once. Click on images to enlarge. The above is a very sought after collectible that was circulated back in 1967-1968. This picture above (From Jim Pinkerton) is of a pen...

Good used pit free emblem. We now have the black background decal in reproduction form. Casing number: C9WB-18B000 Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

This is a used coral with a new background decal and walking cat emblem. We ship the three parts unassembled so you can re-chrome the corral if you desire. The corral will not be perfect but it will not be heavily pitted either. You can expect the part you receive to resemble the one pictured here.Casting number: C9WB-18B000

This vinyl piece glues to the center of your block off plated on Cougars not equipped with AC. These often times have shrunk slightly over time. We cannot guarantee to always have all the colors in stock. Call for color availability or put desired color into the comments section of your order.

Restored emblem / insert for the 69 Cougar center grille. These are sold on an exchange basis, so you must have a good core with both studs intact. The emblem will be without the decal in the center. You can get it here. Ford casting number reads C9WB-8B369-A NOTE! If you pay the core charge on our 1969 restored grille parts or complete grilles we will be under the assumption you do not have cores to send in or they are average quality with pits and cracks. If you have really clean cores you...

Good used emblem with both studs intact, no obvious pitting or scratches. This item will have a faded center decal, and you will need a new decal. You can either add a note to the order asking that we contact you about upgrading to an emblem with less fade for a upcharge, or get a reproduction decal here. Ford casting number reads C9WB-8B369-A ...

This grille background piece requires you remove your Cougar emblem before installing. To remove the cat emblem you will need to grind from the backside and epoxy the emblem back in place after-wards. Vast improvement over your current faded, dinged part. Not for use on the xr7. ...

Restored corral for the passenger side eyelid on the 1969 Mercury Cougar. This is just the outer corral and does not include the background decal or the walking cat emblem. NOTE! If you pay the core charge on our 1969 restored grille parts or complete grilles we will be under the assumption you do not have cores to send in or they are average quality with pits and cracks. If you have really clean cores you will want to send them in advance and not pay the core charge so we can do what we call...

Adhesive backed, located on the right side of your deck lid.  We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often, as you can see one of our example photos above, the line workers did not even attempt to get them very well centered. Both emblems were placed on the RH side of the deck lid "somewhat" centered top to...

These are sold as a pair and are of marginal quality. The material is much softer than original, the chrome is of a low quality and compared to original the detail is not nearly as crisp. Check out this video

Reproduction pair of quarter panel scripts with black trim for the 1968 Mercury Cougar. The correct version had no black paint around the letters. This is a one time only limited run of this custom emblem, and when they're gone they're gone! *Only sold as a pair

New product that is in stock and ready for shipment now! Concours quality, perfect fit and a great value for the money. These little emblems are often the first thing one sees as they approach your car as they are at eye level. These emblems are located on the "C" pillars of your 67 - 68 Cougar but can also be used on a 71-76 Cougar with little or no modification. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C'...