Rare, almost impossible to come by collectors item designed to adhere to the inside of your window. Original water transfer 3" diameter Cougar logo decal. Soak in water for 30 seconds and slide onto glass. I have only seen these dealer "give aways" one other time in all my years of collecting. We want to you to keep in mind that the cloudy areas you see on the decal in the picture are nothing more than paper residue, and will easily wipe off. Check out this video ...

Nicely done reproduction with the only difference being that it adheres to the outside of the window and the originals adhere to the inside. Check out this video

Reproduction Dan Gurney Special window decal in black and gold for the Mercury Cougar. Check out the very first Cougar

Tips for installation: Decal should be trimmed to resemble the original decal. This one is comes as a full rectangle and the original was trimmed around the edges w/ very little clear border left.This decal is a very "touchy" decal, any air bubbles WILL leave the adhesive white where the bubble was even if you get it smoothed/pushed out so you must put the decal down avoiding ANY air bubbles by laying one edge first and rubbing as you go along. If you just lay the decal down you WILL end up w...

Replaces Ford part #C8AZ-6223362-A. Sold in pairs, four required per car, used on most Ford products. We often get calls like "How do I remove my front window cranks?" Unlike the rear cranks that are held on by an Allen set screw, the fronts have a Phillips screw under this decal. If you are careful, often you can reuse your original and glue it back in place.

Reproduction 351 4V AT / MT Emission Decal for 1969 Mercury Cougar / Ford Mustang

Set of 5 reproduction firewall inspection decals. During final inspection, these decals where placed in different locations on the firewall / cowl area and one P decal between the weatherstrip and dash pad inside the drivers door jam. This decal set has the assembly line inspectors names stamped on them. These decals would have been used on cars equipped with Boss 302 and BOSS 429 engines.

Reproduction Decal Set / Under Hood Paint OK for the 1969 - 1971 Mercury Cougar or 1971 Ford Mustang 

Here are our reproduction black 428 CJ fender decals for your Mercury Cougar. These are the same size and font of the originals and would look killer on any Ford equipped with the 428 engine. We were able to get our hands on a NOS decal to use for reference, so these are spot-on. See pictures for placement on the fender. Each decal measures 5 9/16" x 7/8".Replaces Ford part # C9WY-16228-B.

Here are our reproduction white 428 CJ fender decals for your Mercury Cougar. These are the same size and font of the originals and would look killer on any Ford equipped with the 428 engine. We were able to get our hands on a NOS decal to use for reference, so these are spot-on. See pictures for placement on the fender. Each decal measures 5 9/16" x 7/8".Replaces Ford part # C9WY-16228-B.

There never was an Eliminator convertible from the factory, but we think there should have been. Since the rear quarter panels are shaped differently, we redesigned the side stripes to fit the contours of the convertible Cougar correctly. Otherwise, these are the same stripes we sell in coupe format, cut from OE-spec 3M Scotchcal vinyl and designed from a NOS stripe kit. The kit includes 17 separate pieces, including all side stripes, hood stripes, rear spoiler stripe, ELIMINATOR rear quarter...

This is our complete black stripe kit for the 1970 Cougar Eliminator. The kit includes 17 separate pieces, including all side stripes, hood stripes, rear spoiler stripe, ELIMINATOR rear quarter panel decals, and the often-overlooked 3-piece rear trim blackout stripes. This is the most correct and complete kit you'll find anywhere. Designed using a NOS stripe kit as a reference, and cut from the same 3M satin black vinyl that Ford used from the factory. *Convertible owners - If you're planning...

Black stripe kit for the 1969 Cougar Eliminator. This is the most correct kit you'll find anywhere. Designed using a NOS stripe kit as a reference, and cut from the same 3M satin black vinyl that Ford used from the factory. Kit includes 8 pieces for the fenders & extensions, doors, and quarter panels.Copy of original Ford decal instructions included. Note that these stripes are supposed to go on in a straight line, they do not curve down with the body line. See car picture in this listing for...

There never was an Eliminator convertible from the factory, but we think there should have been. Since the rear quarter panels are shaped differently, we redesigned the side stripes to fit the contours of the convertible Cougar correctly. Otherwise, these are the same stripes we sell in coupe format, cut from OE-spec 3M Scotchcal vinyl and designed from a NOS stripe kit. Quality and fit are second to none. There was also never a white Eliminator stripe kit in 1970 (unlike 1969) but we figured...

This is our complete white Eliminator stripe kit for 1970 Cougar coupes. There was never a white Eliminator stripe kit from the factory in 1970 (unlike 1969) but we figured we'd make these available for those wanting a custom look. Designed using a NOS stripe kit as a reference, and cut from OE-spec 3M vinyl, fit and quality are second to none. The kit includes 14 separate pieces, including all side stripes, hood stripes, rear spoiler stripe, and ELIMINATOR rear quarter panel decals. Unlike...

White stripe kit for the 1969 Cougar Eliminator. This is the most correct kit you'll find anywhere. Designed using a NOS stripe kit as a reference, and cut from the same kind of 3M vinyl that Ford used from the factory. Kit includes 8 pieces for the fenders & extensions, doors, and quarter panels.Copy of original Ford decal instructions included. Note that these stripes are supposed to go on in a straight line, they do not curve down with the body line. See car picture in this listing for...

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very...

Used Grade A condition 6.5 litre (390) aluminum fender emblem / badge for the 1967 Mercury Cougar. We rarely get these in fantastic condition and most of what we get looks like the one pictured with several small blemishes. Often, one of the two studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed nuts. These were used on all XR7G models with an S or X code 390. On other Cougars, they were used on those that came equipped...

Used 6.5 litre Grade A (390) fender emblem for the Mercury Cougar. We rarely get these in fantastic condition and most of what we get looks like the one pictured on our grade B listing with several minor blemishes. No studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed nuts. These were used on all XR7G models with an S or X code 390, on other Cougars they were used with the Cougars that came equipped with a 390, but without the...

Used Grade B condition 6.5 litre (390) aluminum fender emblem / badge for the 1967 Mercury Cougar. We rarely get these in good condition and most of what we get looks like the one pictured with several pits and small blemishes. Often, one of the two studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed nuts. These were used on all XR7G models with an S or X code 390. On other Cougars, they were used on those that...

Used Grade B 6.5 litre (390) fender emblem for the Mercury Cougar. Most of what we get looks like the one pictured with several blemishes. Often one or more of the four studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed nuts. These were used on all XR7G models with an S or X code 390, on other Cougars they were used with the Cougars that came equipped with a 390, but without the GT option package. We also have...

Reproduction 6.5 litre (390) fender emblem for the Mercury Cougar. These were used on all XR7G models with an S or X code 390, on other Cougars they were used with the Cougars that came equipped with a 390, but without the GT option package. Unlike the originals these do not have mounting studs, but are firmly held in place with 3M VHT double sided emblem tape.

Good used pit free emblem that would be good for restoration. Notice the clips are in place and there are no cracks in the plastic backing. The example picture of the installed emblem is what they looked like when restored. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.

This used grade A emblem will have good chrome and mounting studs and plexi center. Ford engineering number on backside is D1WB65517A20-AB. We also offer new barrel nuts for installation. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot...

This used grade B emblem will have good chrome and mounting studs, but the plexi center will be faded. These can be opened up and repainted from the backside. The paint can be obtained from stores that sell modeling supplies. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Ford engineering number on backside is D1WB65517A20-AB. We also offer new barrel nuts for installation. ...

Used Grade "B" center grille emblem for the 71 - 72 Standard Cougar. Will have fading, pitting and the plastic lens area will need to be restored. Ford part number D1WY-8A223-A

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

Located on the right hand dash panel of your XR7, requires drilling to remove properly.

Good used plastic emblem with no peeling chrome. This was used on all models except XR7 on the right side. We also have the metal version of this emblem available.

Grade "A" pit free original metal emblem for your Eliminator or Standard model Cougar. If you look closely at our picture you will in fact see tiny imperfections in the chrome. We rarely ever get flawless examples of this particular emblem as the original plating was substandard (in our opinion). This emblem was used on the standard, decor and Eliminator models.

Grade "B" original metal emblem for your Eliminator or Standard model Cougar. Grade B emblems will have pitting and faded or missing paint. We rarely ever get flawless examples of this particular emblem as the original plating was substandard (in our opinion). This emblem was used on the standard, decor and Eliminator models.

Good used emblem with no bends, but will be scratched. Will need new adhesive tape as these did not come with studs. For any Cougar, but only came on 1969-70 Standard Models, and all 1971-73 Mercury Cougars. 1971-73 XR7 and Standard Models, as well as convertible.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in...

Grade A used, trunk emblems for 1969-70 XR7 models. We will very seldom have this in stock, the alternatives are grade B used or reproduction. Please see related items below. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line workers did not even attempt to get them very well centered. Both...

Due to corrosion caused from the exhaust this used emblem will most likely have poor quality chrome. The emblem shown would be the very rare exception.

Will show at least a small amount of pitting. Casting number as seen on the back reads D0WB-652803-E.

Used driver side (left hand) XR7 door panel emblem for the Mercury Cougar. The emblem shown is not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold individually. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

Used passenger side (right hand) XR7 door panel emblem for the Mercury Cougar. The emblem shown is not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold individually.

Used XR7 door panel emblems for the Mercury Cougar. The emblems shown are not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold as a pair.

Left is the same as right, one year only emblem at the center top of the door panel. Usually will show a small amount of pitting. Casting number as seen on the back reads D0WB-6520802.

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of some late 67 and all 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T. Licensed by FORD ...

This is the aluminum emblem which mounts on the center of all scuff plates. Features raised script surrounded by "Product Of Ford" like original, adhesive backed and protective coating. Sold individually, two required per car. Replaces Ford part # C8ZZ-6513208-T.  Technically this is the version found on early 1967 cars, the late 67 and 1968 versions had a larger blue oval 'Ford', and did not have the 'Product of' line.

These fender emblems look much like the 1968 quarter panel emblems but differ in that they have longer studs that fasten via barrel clips as opposed to a speed nut used on the 1968 quater panel emblems. The Ford casting number on the backside is D1WB-16098-AA. For the money, The 1968 repro quarter emblem is a much better buy . ...

These were on the lower rear portion of early 1967 390 GT Cougar fenders. In later 67 and 68 the separate G and T letters were used on the Mercury Cougar. Comes with replacement tubular nuts as shown. Other applications include 1967 Mercury Cyclone GT and 1968 Mustang GT. The GT rectangle badge was used until sometime between 11/22/66 and 1/28/67, after that, the individual letters were used.Ford part number C7GY-16098-BFord Casting number C7GB-16720-B ...

These were on the lower rear portion of early 1967 390 GT Cougar fenders. In later 67 and 68 the separate G and T letters were used on the Mercury Cougar. Comes with replacement tubular nuts as shown. Other applications include 1967 Mercury Cyclone GT and 1968 Mustang GT. The GT rectangle badge was used until sometime between 11/22/66 and 1/28/67, after that, the individual letters were used.Replaces Ford part number C7GY-16098-B ...

These were on the lower rear portion of early 1967 390 GT Cougar fenders. In later 67 and 68 the separate G and T letters were used on the Mercury Cougar. Comes with replacement tubular nuts as shown. Other applications include 1967 Mercury Cyclone GT and 1968 Mustang GT. The GT rectangle badge was used until sometime between 11/22/66 and 1/28/67, after that, the individual letters were used. Ford part number C7GY-16098-B ...

Decent reproduction of the 69-70 Cougar fender extension COUGAR script. This emblem was used for 2 years only and was located on the driver side front fender extension (fender cap). The originals came with speed nuts but these have push on clips from the back which means they are easier to install as no tools are needed. If one looks very close you will see minor differences compared to original examples. If you want to trade in your dull, pit free emblem for store credit we will give $20 for...

Used front fender extension "Cougar" script. The one you receive may not look as good as the one pictured but will be very close in condition, expect one of the four studs on the back to be missing. Ford Engineering number as found on the backside: C9WB-16098-B Ford number C9WB-16098-A. Note that the 1970 version stamped D0WA-16098-A is slightly different, most noticeable on the letter "C".

Used front fender extension "Cougar" script. The one you receive may not look as good as the one pictured but will be very close in condition, expect one of the four studs on the back to be missing. Ford Engineering number as found on the backside:  Ford number D0WB-16098-A. Note that the 1970 version is stamped D0WA-16098-A.