Body

This is our reproduction, uncut, driver side (left hand), long, front and rear floor pan for your Mercury Cougar convertible.

This is our reproduction, uncut, passenger side (right hand), long, front and rear floor pan for your Mercury Cougar convertible.

This is a reproduction long front and rear floor pan. Will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but this will work for all years.

Reproduction full length driver side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years. Hi, and sincerely thanks for all help I've received from WCCC during my (mega) 1968 restoration project. If everyone would be that helpful, the world would be a much better place. ;-) My car is almost ready for the road, but - as always - there...

This is a reproduction long front and rear floor pan. Will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but this will work for all years.

Reproduction full length passenger side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years.

Replaces Ford part #D1AZ-6522428. Sold individually.

Door lock and trunk lock gasket as found on all 1969-73 Mercury Cougar. Gasket used to seal the lock cylinders to the exterior door on all 1967 - 1973 Mercury Cougar and Ford Mustang as well as the trunk lock gasket on all 1969-73 Mercury Cougar. It is not used for the trunk lock cylinder on the 1967 - 1968 Mercury Cougar because they uses a flip up trunk lock cover that instead uses a gasket between the covers housing and the trunk. Replaces Ford part #C7AZ-6243625.

Used driver side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

Used driver side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

Used passenger side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

Used passenger side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

The 1971 - 1973 Mercury Cougar came with either Tier or Perforated headliner, so make sure you choose the correct texture. All of the colors with the exception of Dark Green and Dark Blue are available in either texture. *NOTE* Colors other than black and white are special order and ship directly from the manufacturer. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic...

The 1971 - 1973 Mercury Cougar came with either Tier or Perforated headliner, so make sure you choose the correct texture. All of the colors with the exception of Dark Green and Dark Blue are available in either texture. *NOTE* Colors other than black and white are special order and ship directly from the manufacturer. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic...

The 1971 - 1973 Mercury Cougar came with either Tier or Perforated headliner, so make sure you choose the correct texture. All of the colors with the exception of Dark Green and Dark Blue are available in either texture. *NOTE* Colors other than black and white are special order and ship directly from the manufacturer. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic...

The 1971 - 1973 Mercury Cougar came with either Tier or Perforated headliner, so make sure you choose the correct texture. All of the colors with the exception of Dark Green and Dark Blue are available in either texture. *NOTE* Colors other than black and white are special order and ship directly from the manufacturer. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic...

The 1971 - 1973 Mercury Cougar came with either Tier or Perforated headliner, so make sure you choose the correct texture. All of the colors with the exception of Dark Green and Dark Blue are available in either texture. *NOTE* Colors other than black and white are special order and ship directly from the manufacturer. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic...

The 1971 - 1973 Mercury Cougar XR7 came with Tier and standard came with Perforated headliner, so make sure you choose the correct texture. All of the colors with the exception of Dark Green and Dark Blue are available in either texture.Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

The 1971 - 1973 Mercury Cougar XR7 came with Tier and standard came with Perforated headliner, so make sure you choose the correct texture. All of the colors with the exception of Dark Green and Dark Blue are available in either texture.Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

The 1971 - 1973 Mercury Cougar XR7 came with Tier and standard came with Perforated headliner, so make sure you choose the correct texture. All of the colors with the exception of Dark Green and Dark Blue are available in either texture.Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

The 1971 - 1973 Mercury Cougar XR7 came with Tier and standard came with Perforated headliner, so make sure you choose the correct texture. All of the colors with the exception of Dark Green and Dark Blue are available in either texture.Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

The 1971 - 1973 Mercury Cougar XR7 came with Tier and standard came with Perforated headliner, so make sure you choose the correct texture. All of the colors with the exception of Dark Green and Dark Blue are available in either texture.Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

Pair of used wire anchors for keeping the rear most headliner bow stationary. These are fragile wires, and prone to rusting. We try to keep them in inventory. 1971-73 anchor wires are 4-9/16 inches long. A DIY person can improvise these pretty easy, using lengths of regular wire. Ford part # C6AB-6352180-A.

Contrary to what you might think at first glance, the support rods used in 1971-73 Mercury Cougar headliners are not the same from front to back. Each of the rods is bowed to a different curve. To replace a headliner and make it look right, you must install the rods in the same order as they came out from the original locations. To help you do this, Lincoln-Mercury coded each rod with a color applied to each end. 1st. Driver Side: Pink - Passenger Side: Pink 2nd. Driver Side: Pink - Passenger...

Good used frame used to stretch your head liner over on the interior side of your sliding sun roof panel. The picture above is the support strip that runs through the middle At its widest points this frame measures 35 1/4" x 20 15/16" ...

Good used cut off driver side, trunk or deck lid hinge. Fits all 1971-72 Mercury Cougar and Cougar convertible models. Sometime in 1972, the hole spacing for the trunk lid changed from 3 inches to 4-1/4 inches spacing. This hinge will have the 3 inch spacing. These are welded to the body, expect some cleanup to the metal prior to welding. We do not drill spot welds.Additionally fits 1971-73 Mustang hardtop and convertible models (body style 65 and 76). Ford part number D1ZZ-6542700 and...

Good used cut off passenger side, trunk or deck lid hinge. Fits all 1971-72 Mercury Cougar and Cougar convertible models. Sometime in 1972, the hole spacing for the trunk lid changed from 3 inches to 4-1/4 inches spacing. This hinge will have the 3 inch spacing. These are welded to the body, expect some cleanup to the metal prior to welding. We do not drill spot welds. Note that there are an early and late style of these hinges. Early style has a bolt spacing of 3 inches for installing the...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Grade A hoods have no rust under the lip, nothing more than a light skim coat of filler found anywhere, no damage in the hinge areas...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Our grade B hoods are 100% rust free with minor damage to the top side. Hoods are shipped via www.forwardair.com so check their site...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Good used OEM original driver side hood hinge. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. It is easier to fit and adjust these hinges prior to installing the springs on them. Here is a helpful youtube video that shows you how to...

Good used OEM original passenger side hood hinge. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. It will be easier to fit and adjust the hinge prior to installing the spring on the hinge. Here is a helpful youtube video that shows you how...

Good used OEM original hood hinge set. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. Fits 1971-73 Mercury Cougar and Ford Mustang. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the springs.Ford...

Welded in hooked retainer for the rear seat back installation on any 1967-73 Mercury Cougar or Ford Mustang coupe or hard top body style. This bracket welds to the edge of the package tray. Two hooks per car, sold individually. We cut out a individual sections as shown. Make good measurements prior to removal of your old brackets. You will need to drill out the spot welds prior to installation. For sure that basic Ford part number is 62118.

Ignition lock set is new original from the O.E.M. source. Factory fresh with two keys. Fits 1970 through 1973's manufactured before 5/17/1973. Replaces Ford Part #: D0AZ-11572-A, D2AZ-11582-B, SW-1114.

Guide that measures 10 5/8" long held in place by the outer trim that has four screws. Driver and Passenger are interchangeable.

New old stock driver side interior door handle for base Standard model 1971-73 Cougar, 1971-73 Ford Mustang and Maverick and Torino. Ford part number D1AZ-6522601-ANote - Does not fit most standard Cougars or all XR7's. Interior code has to start with a 1 or letter A.

New old stock passenger side interior door handle for base Standard model 1971-73 Cougar, 1971-73 Ford Mustang and Maverick and Torino. Ford part number D1AZ-6522600-A Note - Does not fit most standard Cougars or all XR7's. Interior code has to start with a 1 or letter A.

Used on both the Xr7 and Decor / Deluxe interiors with moulded door panels.

Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford #: C7AZ-6222053-A.

Reproduction economy trunk / glove box key. These keys DO NOT have the Ford logo.Replaces Ford Part #: C7AZ-6243562-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford Part #: C7AZ-6243562-A.

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the ignition / door key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the trunk / glove box key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

Zinc plated, visually correct copies of the original, very prone to failure... We highly recommend buying our good used latches linked here even though they may not look as pretty. No warranty on this low quality off shore part.Replaces Ford Part # C5AZ-6243200-A Check out this video