Body

We can honestly say these are much better than the originals when it comes to durability. The originals were backed with a "fiber-board" that was prone to failure in the clip areas and almost always curl at the edges with age. These new panels are backed in sturdy, moisture proof ABS plastic and covered with the correct textured vinyl. Secondly this much improved new version does not crack in the arm rest area like the originals. You will have to reuse your original decorative trim, emblems...

We can honestly say these are much better than the originals when it comes to durability. The originals were backed with a "fiber-board" that was prone to failure in the clip areas and almost always curl at the edges with age. These new panels are backed in sturdy, moisture proof ABS plastic and covered with the correct textured vinyl. Secondly this much improved new version does not crack in the arm rest area like the originals. You will have to reuse your original decorative trim, emblems...

This is the factory Ford remote trunk latch as used on luxury cars such as Thunderbird or Lincoln. As you can see from the photo, they are made (and install) exactly like our Cougar trunk latches, but with the addition of a release tab. These can be installed to use either a cable, vacuum, or solenoid release.

Nice used original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds with hardware. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on center. This rack was utilized for may years on many cars. The same company made them for...

This unique gasket is only slightly different from the driver side. The angle at the front is just a little different and notice it does not have a hole drilled for the remote mirror cable used on the driver side. This gasket was also used on the 1971 Ford Torino / Ranchero and Mercury Cyclone. This is an upgrade over the reproduction we carry for a 1969 - 1970 Cougar that has a passenger side Sport Mirror. The Ford Engineering number seen on the pad reads D1OB-17724-AA. Do you have questions...

Original used hard plastic sport mirror pad / gasket. Correct for driver side sport mirrors for the 1971-73 Cougar and passenger side sport mirrors 1970-73. Ford engineering # C90Z-17724-B and D1WB-17C701-AB. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road? WCCC to the rescue! ...

This used driver side (left hand) mirror pad / gasket for use with a standard manual adjust chrome mirror. This unit will not work with a painted sport mirror or any remote mirror. Ford Engineering # imprinted on pad is C7OB-17C701-AA or C8OB-17C701-A. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a...

Used interior quarter window moulding for the driver side (left hand) of the Mercury Cougar coupe. This trim installs vertically behind the quarter window. Unfortunately we cannot guarantee we will be able to supply the color of your choice, but we will try to accommodate.

This passenger side (right hand) moulding is correct for hardtop or coupe. On convertibles, the top portion is trimmed to allow it to slide under the sun visor bracket. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-6503598, engineering # imprinted on the back D1ZB-6503598 for 1971-72, D3ZB-6503599 for 1973. *NOTE* Excludes Mustang Fastback and Mach 1 models. This...

This driver side moulding is correct for hardtop or coupe. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503599 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Master part number D1ZZ-6503599.*NOTE* - Excludes Mustang Fastback and Mach 1 models. ...

1971 - 1973 Convertible spare tire mounting, J bolt. MPC lists the total length as 9-1/2 inches long, and 5 inches threaded. Application is for hubcap type wheels only, those of you fortunate to have the style steel wheels need C8OZ-1448-A above.

There currently are no reproductions of this curved, thin package tray. Included with the tray are both slender strips of thin sound deadener / insulation. These package tray cover boards will not have heavy water damage, but will need paint. Replaces Ford part number D1WY-6546668-A.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM plastic and leather paint prep is for cleaning surfaces before applying the SEM flexible vinyl paint. Removes mold, grease, oil and other contaminates from leather, carpet, velour and vinyl.

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons, radiator support, transmission, rear end housing, sheet metal, glass and variety of other parts. It's often little details like this that separate first and second place at the show.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward. Thus you will want this panel for the passengers side of those series. ...

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward, Thus you will want this panel for the drivers side of those series. 

1971-72 Mercury Cougar convertible driver side. Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of the mounting studs. Please choose which side and year you need. There are very slight differences on 1973 and they do carry different part numbers. Ford casting # D1WB-7628519, Mercury MPC # D1WY-7628011-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

1971-72 Mercury Cougar convertible passenger side. Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of the mounting studs. Please choose which side and year you need. There are very slight differences on 1973 and they do carry different part numbers. Ford casting number D1WB-7628518, Mercury MPC number D1WY-7628010-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form and since almost every panel has "some" minor...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Our used driver side grade "B" quarter panels are still good panels, but will need more body work than the Grade "A" panels, due to...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form, and since almost every panel has "some" minor...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Our used passenger (right hand) side grade "B" quarter panels are still good panels, but will need more body work than the Grade "A"...

Driver side, rear frame rail, from a 1971, 1972, and 1973 Mercury Cougar convertible. The Ford MPC shows a couple of different numbers and exceptions for this item. It may be the presence or absence of the nutserts for the rear sway bar option. If the sway bar nutserts are needed, please contact WCCC for availability. Full length, we cut so that there is some remaining metal on the edges. Ford part number D2WY-7610125-B.* Note - this item has dimensions in excess of 75 inches, and will ship as...

Passenger side, rear frame rail, from a 1971, 1972, and 1973 Mercury Cougar hard top. The Ford MPC shows a couple of different numbers and exceptions for this item. It may be the presence or absence of the nutserts for the rear sway bar option. If the sway bar nutserts are needed, please contact WCCC for availability. Full length, we cut so that there is some remaining metal on the edges. Ford part number D2WY-7610124-B.* Note - this item has dimensions in excess of 75 inches, and will...

Heavy duty door hinge rebuild kit for the 1971 - 1973 Cougar or Mustang. Included in the kit are:2 Machined hinge pins2 Machined steel tubes4 Oil impregnated bushings2 Stainless steel washers2 Zerk FittingsEach kit is enough to do one side and includes one big and one small pin / tube set.

New old stock Ford accessory cable trunk popper. Fits late 1967 - 1973 Mercury Cougar and other Ford products. Lever release, complete kit, NOS Ford. Detailed instructions included.  Ford part number C7AZ-62432A00-A. *Note - All 1967, and most 1968 trunk lids will not have a large enough access opening in the under side structure to allow the trunk latch to be inserted. 

New old stock Ford accessory electric trunk popper. Fits late 1968 - 1973 Mercury Cougar and other Ford products. Electric push button release, complete kit, NOS Ford. Detailed instructions included.  Ford part number C9AZ-54432A00-A. *Note - All 1967, and most 1968 trunk lids will not have a large enough access opening in the under side structure to allow the trunk latch to be inserted. 

This mirror nut for the 70 - 73 Cougar or Mustang is made from stainless steel, as compared to the other reproduction we offer which is made from die cast metal. A few benefits of the stainless steel nut is that the finish on it will not tarnish over time, and that it cannot be cross threaded.

Reproduction scissor jack for any year Mercury Cougar or Ford Mustang. This is a cheap Chinese jack that is clearly marked "For Display Use Only, Not for Lifting Vehicles". It resembles an original scissors jack, but there are several differences. It functions properly and will lift weight, but we wouldn't use it on any of our personal cars. This is the ACME brand like used by Wile E Coyote.

Original scissors jack. We save the working ones that come to our yard. Hinge points should get little oil or a quick spray of WD-40. Wipe down the residual grease and oil and stow it in the trunk again! Notice the correct placement of the instruction decal. That's the tip of the day! *NOTE* There are multiple versions of this jack that differ in the area that makes contact to the rocker and the thread pitch. We will be sorting out those differences and posting our findings here soon. ...

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

Here is a real treat! New in the Ford box driver side (left hand) mirror, very hard to come by these days. *NOTE* XR7 and GT Cougars ordered with a "special paint" color got this chrome mirror in place of the color keyed sport mirror that came standard with those option packages. A small credit was given for the trade down and was shown on the invoice. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror...

This used grade "A" remote mirror has chrome that looks great and the adjustment wand is unbroken and working. Used on the drivers side of standard Cougars, no passenger side mate was ever offered with this mirror. Two different versions of this mirror are found on 1971-73 Mecury Cougars, either casting number D1WB-17743-AA or C9AB-17743-A will be supplied.Replaces Ford part numbers D1WB-17743-AA and C9AB-17743-A.Do you have riv-nut questions? Here are riv-nut answers! ...

This used grade "B" remote mirror has chrome that looks shabby, adjustment wand is unbroken and working. Used on the drivers side of standard Cougars, no passenger side mate was ever offered with this mirror. Two different versions of this mirror are found on 1971-73 Mecury Cougars, either casting number D1WB-17743-AA or C9AB-17743-A will be supplied.Replaces Ford part numbers D1WB-17743-AA and C9AB-17743-A.Do you have riv-nut questions? Here are riv-nut answers! ...

This NOS remote mirror came to use without a Autolite or Motorcraft box. Current offering while new and never installed does have a small manufacturers defect in the casting as shown. Found on the drivers side of standard model Cougars, no passenger side mate was ever offered with this mirror. Two different versions of this mirror are found on 1971-73 Mecury Cougars, either casting number D1WB-17743-AA or C9AB-17743-A. This mirror has the Ford casting number D1WB-17743-AA. Do...

Used manually adjustable grade "B" side view mirror for the Mercury Cougar Standard or Ford Galaxie. This ambidextrous mirror can be installed on either the passenger or driver side door. This good used mirror will have good glass and will have some pitting in the chrome as shown. Also used on various 1967-73 full sized Ford and Mercury cars. Replaces Ford part # C7AZ-17696.Dimensions: Base Hole Spacing: 5-7/8"Base Length: 6-5/8"Overall Height: 5-1/8"Mirror Width: 5-1/8"Mirror Height: 3-5/16"...

This plastic fastener is used to keep your mirror cable from interfering with the movement of your door glass. It is located at the front of the door near the top.

Complete Service part mirror assembly for any Cougar with the sport / bullet racing style mirror. Casting number as seen on base is D1WB-17743-B.Ford part number D1WY-17682-A

Ford Casting number as seen on the bottom side is D1OB-17713-AWA. Many people misinterpret it as D10B-17713-AWA, DI0B-17713-AW or Dl0B-17713-AWA. Perfect base with no cracks or bends. Visually it is impossible to tell this part from 1970 with a D0OB-17713-AW casting number on the bottom. The Pastel Blue base is from a 1970 and the Red base from a 1971. Even when placed side by side it is hard to tell the difference. Do you have questions about installing a passenger side mirror or using...

NOS passenger side (right hand) sport mirror that is correct for the Mercury Cougar. This will also work on 1969-70 Cougar, but base height is just a little bit taller. Replaces Ford part # D1OB-17713 Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road? WCCC to the rescue! ...

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

Original space saver tire marked F78-15 from a 1970's Mercury or Ford. GoodYear brand it has the larger hub size, bolt pattern is 5 on 4-1/2. Not sure if it has ever been inflated, it is collapsed as shown.  Just looking for a space saver spare? This is it, it looks the part to those that casually look in the trunk of the car at a car show. Tread is period correct for a Goodyear tire, but typically B.F. Goodrich was optional on 1968-69 Cougar or Mustang. *NOTE* Does not include...

Nice unused space saver spare tire for a Ford. Vintage Good Year brand tire with size F78-14. BF Goodrich is another common brand of tire installed for use with unique storage location, hold down, and inflation bottle. This one does not appear to have been inflated or used on the road. Still has the nubs on the face of the tire as shown.

Reproduction 6 1/4" Spare Tire Mounting Bolt 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

Used manually adjustable grade "A" side view mirror for the Mercury Cougar Standard or Ford Galaxie. This ambidextrous mirror can be installed on either the passenger or driver side door. This good used mirror will have good glass and nice chrome for your restored or nice original Cougar or Galaxie. Also used on various 1967-73 full sized Ford and Mercury cars. Replaces Ford part # C7AZ-17696.Dimensions: Base Hole Spacing: 5-7/8"Base Length: 6-5/8"Overall Height: 5-1/8"Mirror Width:...

Used driver side (left hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind you...