All Products

Best replacement for the original wiper blade assembly. Replaces Ford part #: D4AZ-17528 and C9AZ-17528-A. Sold individually

Made by Trico who made them originally for Ford. Replaces Ford part #: D1ZZ-17528-A. Sold individually

Original black windshield wiper blade holder. Fits any 1971-73 Mercury Cougar or Ford Mustang. Sold individually, two per car, 18" rubber wiper blade not included.Replaces Ford part #: D1AZ-17528-C or D3AZ-17528-A.

Original Trico stainless wiper holder assembly, removed from a 1970 Mercury Cougar. Fits any 1969-70 Mercury Cougar and Ford Mustang. Has the original metal fastener to connect to your wiper arm, rather than the plastic piece used in the reproductions. Sold individually, two per car, 16" rubber wiper blade not included.*Note - This is NOT, repeat NOT the ultra rare 1969 production wiper blade holder assembly. This is a Trico 16 inch blade holder as found on most 1970 cars.

Original FoMoCo used two speed windshield wiper motor for your 1967-68 Mercury Cougar or Ford Mustang. This used motor comes as shown with wiring harness for all 1967-68 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1967-68 installation, must be marked 7Z. Linkage arms sold separately. Stamped C7ZF-17504-D, Ford part # C6OZ-17508-D.

The hinges on these original arms tend to get worn out which will cause irregular movement and can eventually burn up your wiper motor or bind up the linkage. If your wipers do not move in tandem

The hinges on these original arms tend to get worn out which will cause irregular movement and can eventually burn up your wiper motor or bind up the linkage. If your wipers do not move in tandem

This Wiper Pivot To Cowl Seal Reproduction is sold as a pair. Fits both the 67 and 68. Replaces Ford part #: C5ZZ-17475.

Original FoMoCo used two speed windshield wiper motor for your 1969-70 Mercury Cougar or Ford Mustang. This used motor comes with wiring harness with unique grommet for the firewall specific to 1969-70 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1969-70 installation, must be marked 9Z. Linkage arms sold separately. Ford part # C9ZF-17504-C.

Original FoMoCo used two speed windshield wiper motor for your 1971-73 Mercury Cougar or Ford Mustang. This used motor comes with wiring harness, for all 1971-73 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1971-73 installation, must be marked 1Z. Linkage arms sold separately. Ford part #s D1ZF-17504, D2ZF-17504, D1ZZ-17508-A

A nice reproduction of the standard air cleaner wing nut. This version was used on most Ford products through the 1980's.

Reproduction wing nut for the snorkel on your air cleaner. Good for the 1967 Cougar or Mustang.

Correct spare tire hold down wing nut for the 1967 Mercury Cougar or Ford Mustang. Replaces Ford Part #: B9AZ-1462-A.

Spare Tire Mount Wing Nut Reproduction for the 1968 through 1973 Mercury Cougar / Ford Mustang

For 1968 Ford standardized or changed all of the J-bolt threads to the beefier 1/2"-13. We have noted two variations of this wing nut. The most obvious identifier between the two is the tabs in the center. The majority have these tabs present, the minority do not. We also stock and carry the correct disc or hold down plate, and the J bolt. Lots of sizes and lengths for those. Do you have the correct one?

This is the set of six bolts needed to attach the pivot section of the wiper arms to the cowl on 1969-1970 Cougars and Mustangs. Three bolts needed per side

Replaces Ford part #D1ZZ-17430.

This is an exact reproduction of the wiper transmissions that will connect to the wiper motor and the output shafts. It includes correct links and pivots for full range of motion. This is commonly replaced when swapping your cowl panel

Used wiper transmissions that will connect to the wiper motor and the output shafts. This is commonly replaced when swapping your cowl panel, steel dash panel, and/or firewall. If you want to keep your car original, go with these good used arms, or you can find the reproductions here.

Good used D0OZ-17C583-A adjustable windshield wiper stop, as found on any 1971-73 Mercury Cougar, 1971-73 Ford Mustang, 1970-71 Ford Torino, or 1970-71 Mercury Cyclone. Cougar and Mustang use one of these in the center, not sure about the Torino.Will need new rubber dipped like OEM Ford. Replaces Ford part number D0OZ-17C583-A.

Used and reusable backup lamp socket and wiring assembly for the reproduction reverse light chrome housings or to replace a damaged lead in your original 1969-70 Mercury Cougar reverse light. This light socket assembly uses the 1156 bulb. NOTE: These sockets are crimped from the factory and are difficult to remove. When re-installing, there won't be much "meat" left to flare out inside the bezel and you may run into issues with getting a good ground. 

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. Fits 1971 Mercury Cougar and Ford Mustang with 351C engines. About 24 inches in total length. Black wire with yellow hash marks. Ford Part #: D1ZB-19A885-B.

Reproduction Dash to Engine Gauge Feed with push-on Post Oil Sender for the 1967 and 1968 Mercury Cougar with the 289 or 302. Red / Green stripe wire = Coil White / Red stripe wire  = Temp Red / White stripe wire = Oil lamp * Note - Verify your oil pressure switch has the connector to accept the push on boot plug. Replaces Ford Part #: C6DZ-14289-BCheck out the video below on our new gauge tester: ...

Reproduction Dash to Engine Gauge Feed with Tach and Slide-on clip Oil Sender for the 1967 and 1968 Mercury Cougar with the 289 or 302. * Note - Check the style of oil pressure connector on your engine. Replaces Ford Part #: C7DZ-14289-BCheck out the video below on our new gauge tester: ...

Reproduction Dash to Gauge Feed Harness for the 1970 Mercury Cougar and Ford Mustang with either the 351C-2V or 351C-4V, Cleveland engine only. Replaces Ford Part #: D0ZZ-14289-ACheck out the video below on our new gauge tester: ...

Reproduction Dash to Engine Gauge Feed Harness with the push-on post oil sender for the 1967 and 1968 Mercury Cougar or Mustang with the 390, 427 or 428 Big Block. Replaces Ford Part #: C7ZZ-14289-ACheck out the video below on our new gauge tester: ...

Big Block FE 390 or 428 engine feed harness that fits the 1969 or 1970 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C9ZZ-14289-B and D0AZ-14289-A.Check out the video below on our new gauge tester: ...

Plugs into firewall and connects original style oil pressure sending unit, water temperature sending unit and coil. Fits all 1971 Mercury Cougar and Ford Mustang with 429CJ engines. Replaces Ford part number D1AZ-14289-D.Check out the video below on our new gauge tester: ...

Used Dash to Gauge Feed Harness for the 1972 Mercury Cougar and Ford Mustang with either the 351C-2V or 351C-4V, Cleveland engine only. Also bundled with the wires is the air conditioning clutch wire. Used condition, tested and working, professionally repaired, normally these are hard from engine heat. Replaces Ford Part #: D2OZ-14289-DCheck out the video below on our new gauge tester: ...

Reproduction dash to engine gauge feed harness for the Mercury Cougar equipped with the 351 Windsor. All black boot plugs, this is the style used on cars with air conditioning. Fits 1969-70 Mercury Cougar with 351W engines and 1969-70 Ford Mustang with 302 or 351W engines. Check out the video below on our new gauge tester: ...

Reproduction dash to engine gauge feed harness for the Mercury Cougar equipped with the 351 Windsor. All black and yellow boot plugs, this is the style used on cars without air conditioning. Fits 1969-70 Mercury Cougar with 351W engines and 1969-70 Ford Mustang with 302 or 351W engines. Check out the video below on our new gauge tester: ...

Master clip kit which includes following fasteners:Door courtesy and speaker Driver side apronEngine feedFirewallFront crossmemberGas tank senderHorn feedPassenger side apron below relayRadio cable to dashSide marker and headlightsTurn signal lights on hood scoopUnder dashVarious location zip tiesKeep in mind that there are many other fasteners on 1969 Cougars / Mustangs that are not in this kit. ...

Master clip kit which include the following fasteners:Door courtesy and speakerEngine feedFirewallFront crossmemberHorn feedParking light leadsPassenger side cowl brace and alternatorPassenger side shock towerRadio cable to dashSide marker lampsTaillight wiring to taillight body studsTurn signal lights on hood scoopUnder dashKeep in mind that not all fasteners found on 1970 Cougars / Mustangs are found in this kit. ...

Master clip kit which includes the following fasters:Back up light to firewallDoor speakersEngine ffeedRadio cable to dashSide marker and headlightsTaillight wiring and groundUnder dashVarious location zip tiesKeep in mind that not all fasteners found on 1971-73 Cougars / Mustangs are in this kit.

Anti rattle spring for the 1967 Cougar and Mustang clutch release lever spring. Ford part number C6AZ-7562-A.

This extension connects from the instrument cluster wiring harness to the voltage regulator. We've found these on many 68 Cougars, but not all seem to have them.

Used wire extension for the tilt / tilt away steering column found in the Mercury Cougar or ford Mustang. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts needed. To offset the cost of your rebuild, you can send us additional parts or parts columns and we will give...

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.Replaces Ford Part #: C9ZB-19A885-B.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end. Replaces Ford Part #: C9ZB-19A885-B.

Used wiring harness for the 1971 Cougar right hand (passenger side) C pillar lamp. Good for both Standard and XR7 models

Used wire harness with diffusers for the instrument cluster lighting (dash lights) on the Standard or XR7 71 - 73 Mercury Cougar.  NOTE* When using LED ground sensitive bulbs, you must reverse the black and blue w/red stripe wires. Ford part number D1WB-10B898-AA

Used lead wire harness that runs from the white plug at the cowl to the throttle positioning sensor on the 71 - 73 Cougar or Mustang.Harness is red with yellow hash marks.

Reproduction console feed harness for the 67 - 68 Cougar or Mustang. This OEM direct fit wiring harness supplies power from the under dash harness to the console harness.

Wire harness extension that runs from the under dash harness to the A/C fan control switch on any 69 - 70 Cougar Standard or XR7, or the 69 - 70 Mustang.Ford part number C9ZA-19945-B

Complete 25 piece clip kit for the 1967 Cougar or Mustang. Keep in mind that this is produced as a Mustang clip kit, and although most clips are the same between Mustang and Cougar...not all clips apply to Cougar applications.   

Complete 25 piece clip kit for the 1969 Cougar or Mustang. Keep in mind that this is produced as a Mustang clip kit, and although most clips are the same between Mustang and Cougar...not all clips apply to Cougar applications.