All Products

Latch rod that links the door latch and the inside door handle, passenger side door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number D1ZZ-6521940-A.

Latch rod that links the door latch and the inside door handle, right or left side door. 1967 Mercury Cougar and Ford Mustang door latch rods have some slight bends, and a clip midway with a Phillips screw, compared to the 1968 version. Normally this rod was fabric covered. Used rod only, no retaining end clips. Replaces Ford part number C7ZZ-6521940-A. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar...

Latch rod that links the door latch and the inside door handle, right or left side door. 1968 Mercury Cougar and Ford Mustang door latch rods are straight, and do not have a clip midway, compared to the 1967 version. Normally this rod was fabric covered. Used rod only, no retaining end clips. Replaces Ford part number C8ZZ-6521940-A. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click...

1969-70 Mercury Cougar and Ford Mustang latch rod that links the door latch and the inside door handle, right or left side door. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number C9ZZ-6521940-B.

This linkage fits between the gear at the bottom of the key lock and rod that goes to the ignition switch on the fixed column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Ford part number D0AA-3E715-D

Manual control shift linkage assembly for a floor shift C-4 transmission in any 1967-68 Mercury Cougar or Ford Mustang.  Check out this video

This is a correct reproduction C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Manual control shift linkage assembly for a floor shift FMX transmission in any 1969 Mercury Cougar or Ford Mustang. Comes as shown.  1969 linkage is different than 1970, 1970 included a provision for the steering column lock out rod. Check out this video

Manual control shift linkage assembly for a floor shift FMX transmission in any 1970 Mercury Cougar or Ford Mustang. Comes as shown.  1970 linkage includes a provision for the steering column lock out rod, compared to the 1969 version. Check out this video

Manual control shift linkage assembly for a floor shift FMX transmission in any 1971-73 Mercury Cougar or Ford Mustang. Comes as shown. *Note - this will not work with a C6 transmission.

Linkage arm that attaches to the windshield wiper motor that is unique to the 67 - 68 Mercury Cougar and Ford Mustang. These are marked 7Z, among other things the slot is specifically indexed for the 67 - 68 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Linkage arm that attaches to the windshield wiper motor that is unique to the 1969-70 Mercury Cougar and Ford Mustang. These are marked 9Z, among other things the slot is specifically indexed for the 69-70 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Linkage arm that attaches to the windshield wiper motor that is unique to the 1971-73 Mercury Cougar and Ford Mustang. These are marked 1Z, among other things the slot is specifically indexed for the 1971-73 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Replaces Ford Part # C7AZ-6243505-B Click on images to enlarge.

Keyed alike as the originals were, includes two keys, trunk cylinder gasket and retaining clip. Ready to go kit for your 1969 - 1970 Cougar.

Originals keyed alike with Ford key. code on glove box lock matches the trunk lock perfectly. Includes 2 Ford keys, trunk cylinder gasket and retaining clip. Ready to go kit for your 1969 - 1970 Cougar. will fit 1971-73 Cougars, but trunk clip may be different. These used originals are much better than the reproduction lock sets.OEM FoMoCo parts.

Reproduction trunk lock cylinder with keys for the 67 - 68 Mercury Cougar. Replaces Ford Part # C7SZ-6543505-A or C7SZ-6543507-B (Glove box/Trunk lock kit). Below are some basics about removing and replacing your lock cylinder and lock cover. When removing the cylinder from the lock housing this button must be depressed to allow the cylinder to slide out the front of the housing.  The only way to depress the button is to have the key in the cylinder and partially turned as if to...

This rod bridges the gap between the trunk lock cylinder and trunk latch. It is held in place by the round spring that attaches to the back of the trunk lock cylinder. C9WY-6543283-A.1969 and 1970 Cougar only.

This rod bridges the gap between the trunk lock cylinder and trunk latch. It is held in place by the round spring that attaches to the back of the trunk lock cylinder. 1971 - 1973 Cougar only.

A perfectly working, matched set of trunk and glove box locks with key is getting rather hard to come by these days. These two matching locks are guaranteed to work perfectly. Includes 1968 style glove box lock, 1967-68 Cougar trunk lock cylinder with one "Ford" cut key to the coded to the number imprinted on the glove box lock. This is a matching set with new key. 1967 glove box locks has square edges on the front of the lock. Starting in 1968 the lock had a rounded edge on the front. We also...

New Old Stock, NOS, original keyed alike with Ford key. code on glove box lock matches the trunk lock perfectly. Includes 2 Ford keys, trunk cylinder gasket, glove box stainless bezel, and screws. Fits all 1971-73 Mercury Cougar.  OEM Ford part number D1AZ-6543507-A.

Includes two door lock cylinders, two door cylinder gaskets, two keys and one ignition lock cylinder.  Made by the original OEM supplier.  That being said, they do not make them like they used to. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1967-69. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Includes two door lock cylinders, two Ford keys, and one ignition lock cylinder. Assembled from the best used locks. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1970-73. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Sometime after 1973, Ford changed the ignition lock cylinder end. We know it works through 1973, not sure of the change. It must fit the brass lock gear at the bottom of the cylinder hole in the side of the steering column. Refer to your shop manual for removal and installation. Includes two...

Used lock insert for the steering column in the Mercury Cougar or Ford Mustang equipped with the fixed steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used lock insert for the steering column in the Mercury Cougar or Ford Mustang equipped with the tilt steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

Exact replacement inside door handle nut, trunk lock nut, and hood scoop nut. Same finish as originals. 10 of these are used to mount the 68-71 hood scoop found on the 68 428 CJ, 69-70 Eliminator, 69-70 428 Ram Air equipped Cougars and 71 GT and 429CJ. Two of these per door are used on the 69-70 inside door release. Two of of these nuts used to attach 1967-68 Cougar trunk locks.

Correct style nut with captured washer for attaching hood scoops, 1969-70 Mercury Cougar inside door handles, and 1967-68 trunk lock. Correct nuts would have been black phosphate, these are shiny gold as shown.

The four part, die cast vinyl top trim kit requires 15 (right rear under back glass is the odd ball that requires five fasteners) of these speed nut fasteners. These speed nuts also can be used on the 1969-70 Mercury Cougar XR7 dash courtesy light bezels, two for attaching that bezel to the dash pad.*NOTE* These speed nuts only work with factory installed die cast vinyl top mouldings.*NOTE* The factory nuts had a drop of silicone or trim adhesive inside the bowl that acted as a seal. This...

Rod used for locking the 3 speed manual transmission in "Reverse". Connects to the lower tab of the steering column and the reverse control transmission lever shift arm. Prevents the transmission from shifting out of reverse when the ignition key is removed. Rod is about 13-1/2 inches long. The 3 speed manual transmission, could be ordered on any 1970 Cougar with any 351 engine. Transmission code "1" on your door data tag. Ford part number D0ZZ-7E330-B.

Rubber pad for installing the trunk lock mechanism to deck lid. Check out this video

Used locking pawl for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. This pawl is released and via the vacuum motor when the door is opened and the ignition is in the off position. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used original driver side (left hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522135-A.

Used original driver side (left hand) key lock to latch door lock rod for anu 1971-73 Mercury Cougar or Ford Mustang.Ford part # D1ZZ-6522135-A.

Used original passenger side (right hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522134-A.

Used original passenger side, (right hand) key lock to latch, door lock rod for any 1971-73 Mercury Cougar.Ford part # D1WY-6522135-B.

1969-70 Mercury Cougar and Ford Mustang door lock rod. This is the short rod that goes between the door key lock and the latch mechanism. Same part right or left, just under 6 inches in length, no threads on this rod. Ford part number C9ZZ-6522134-A.

Includes three cylinder clips, two door cylinders, two door cylinder gaskets, two keys, one trunk cylinder, one trunk cylinder gasket, and one ignition cylinder. Made by the original OEM supplier. Makes 1 key fit all our locks! Replaces Ford part #: C9AZ-6222050-A

Reproduction lock cylinder set for the ignition and doors on the Mercury Cougar or Ford Mustang. Replaces Ford part # D2AZ-6222050-A.

[No Description Provided]

Reproduction power window lock out switch for all 1969-72 Mercury Cougar and most all other Ford - Lincoln - Mercury cars with power windows in the 1969-72 time frame. Regardless of what you may have been told, this fifth switch found closest to the dash is not a power door lock switch rather it is to "lock-out" the power window on the passenger door and the two windows in the rear so the passengers cannot operate their power windows via their individual switches. Original Ford number...

Regardless of what you may have been told, this fifth switch found closest to the dash is not a power door lock switch rather it is to "lock-out" the power window on the passenger door and the two windows in the rear so the passengers cannot operate their power windows via their individual switches. Treat this switch with care (try not to ever use it) and lubricate it. These are very delicate and hard to obtain. Ford number stamped on the side C9AB-14A695-B.

Used locking lever for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. Two required per car. Here is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the teeth of the locking pawl. We have found that 3 of 4 tilt columns that we have disassembled have locking pawls with broken or chipped teeth. These units will be mint with no broken or chipped teeth....

This is a rebuild service in which we will replace the locking pawl and cable. We provide this service for Cougars, Mustangs and T Birds.Ford part number C9ZZ-3E520-A THIS SERVICE REQUIRES THAT YOU SEND IN YOUR CABLE IN ADVANCE.

New manufactured Tilt / Tilt-Away cable for any 1968-69 Mercury Cougar or Ford Mustang with factory tilt steering column. All new parts developed by our in house steering column expert DW. Not created from used parts. The cable sheathing will not split or crack over time like the originals.Replaces Ford part number C9ZZ-3E520-A*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...