1973 Mercury Cougar

All of our used insulation hood pads are guaranteed to be filthy dirty, less than perfect (as shown) and include at least one spider. We cannot fold these to ship them and they are too large for UPS. You must pick them up in person or we can ship them for free when you purchase a hood from us.

Used XR7 grade "A" main underhood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "A" harnesses are rare, uncut beauties. Good for 1973 Mercury Cougar XR7 models only. Not compatible with Standard model Cougar with AMPS warning light.Ford part # D3WY-14290-B.

Used XR7 grade "B" main underhood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs as where grade "A" harnesses will be rare uncut beauties.1973 Mercury Cougar XR7 models only. Not compatible with Standard model Cougar with AMPS warning...

Nice quality reproduction of the upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1971-73 Mercury Cougar or Ford Mustang. Has the correct length, critical measurements, and contours. Ford part number D1ZZ-7521-B.

Used upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1971-73 Mercury Cougar or Ford Mustang. Has the correct length, critical measurements, bushing, and contours. Ford part number D1ZZ-7521-B.

Special zerk fittings with extra long extensions. Allows easy access to hard to reach zerk fittings. Helps solve squeaky upper control arms.

This vacuum actuated door assembly was used on several performance motors without Ram Air. When extra air was needed under heavy acceleration the vacuum actuator opened the door on the side of the air cleaner base. The actuator on this unit needs to be rebuilt so this is considered a good core only.

This unit mounts on the main air chamber, it opens and closes the air vent. NOS or new old stock.  This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Tested and working, Ford box.Replaces Ford part # C6OZ-18C311-A. ...

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

Used vacuum switching manifold and electrical micro switch assembly from a mid to late 1972 through 1973 Mercury Cougar and Ford Mustang. This is the plastic version with riveted micro switch. We test the micro switches prior to shipping. Please check your A/C controller to verify that you have and need the plastic version of this switch. We also have the all metal version with separate micro switch which can be interchanged, but you would need a micro switch.Ford number D2ZA-19B919-A or...

New Old Stock rear valance for the 71 - 73 Cougar. Original Ford is the best way to go whenever you can.Ford part # D1WY-6540544-A.

Good used, rust free valance. Getting to be hard to find without excessive filler or severe damage. We have a local body man take small dents out and he does not load them up with Bondo. He removes the filler and works the dent out properly. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car. We do have NOS and on occasion we we get in a flawless used example. We have no plans to start selling the fiberglass reproductions as we feel good used, original...

Vacuum tested working hot water valve for any 1969-73 Mercury Cougars or Ford Mustang equipped with factory A/C. This valve stops the flow of warm coolant in the heater hose, when the A/C is on. Has the original cast brass valve and vacuum pod. Used but functional, the reproduction version is very good, but has a black plastic valve, like the service replacement valves from Ford.Replaces Ford part number C9AA-18495-D.

Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73.  A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...

These are original amp meters converted from reading amps to reading volts. Includes new matching XR7 overlay made from top quality 3M 467MP and use 200MP adhesive. The longer 200MP adhesive is in place the stronger it binds.  Click here for a article describing the advantages of a Volt Meter.

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

NOS Water bypass plate for all Ford 351C engines. This is an original in the package brass restrictor plate for 1970-73 Mercury Cougar or Ford Mustang Torino etc.Limited to stock on hand. Replaces Ford Part number D0AZ-8K517-A. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Used hot water tube connector, Grade C condition. Fits 1973 Mercury Cougar and Ford Mustang with EGR valve attached to the carburetor spacer plate. "H" shaped water tube connector with fitting for vacuum thermal valve that controls the EGR valve. These are seldom seen in any condition, Grade C used will have rust through in and on the tube ends. Probably want to get some tubing to fit the inside of the connector tubes, in order to clamp down heater hoses. Vacuum thermal switch switch not...

NOS new old stock driver side (left hand) horizontal quarter window outer weather strip. This is just the one outer weather strip that attaches to the body or XR7 convertible moulding. This rubber piece is included in our reproduction Standard or XR7 convertible belt line kits for 1971-73 Mercury Cougar. Ford part number D1WY-7629733-A.

NOS new old stock passenger side (left hand) horizontal quarter window outer weather strip. This is just the one outer weather strip that attaches to the body or XR7 convertible moulding. This rubber piece is included in our reproduction Standard or XR7 convertible belt line kits for 1971-73 Mercury Cougar. Ford part number D1WY-7629732-A.

Restored driver side (left hand) aluminum channel for installing the roof side, or upper door and quarter window weather stripping. Right and left sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weather strip. Shipping...

Restored passenger side (right hand) aluminum channel for installing the roof side, or upper door and quarter window weather stripping. Passenger and driver sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip....

Used on the 1970 Mustang, 1970 - 1971 Cyclone and Torino and 1971 1972 1973 Cougar style steel wheel 14 x 7". Master Parts Catalog description: 15-1/4" O.D., 11" I.D., 2-3/4" wide. This grade A brushed beauty ring will look right at home on a low mile car, no curb rash!!! Ford part number D0ZZ-1210-B Ford superseded this part with part number in 1974 with D4WY-1210-A which looks the same just a little bit deeper at 2 7/8" deep ...

Used on front doors of cars with factory door speakers. Ford casting number D2AB-7630323-AA. Very hard to find with plastic knob still intact.

Used on front doors of cars with factory door speakers. Ford casting number D3AB-6530323-AA. Very hard to find with plastic knob still intact.

Used on front doors of cars produced after 10-1-71 with no factory door speakers. Ford part number D2AZ-7630322-A, casting number D3AB-6523342-AA. Very hard to find with plastic knob still intact.

Nice reproduction D0OZ-17C583-A windshield wiper stop as found on any 1971-73 Mercury Cougar, 1971-73 Ford Mustang, 1970-71 Ford Torino, or 1970-71 Mercury Cyclone. Zinc plated and rubber dipped like OEM Ford. Cougar and Mustang use one of these in the center, not sure about the Torino. Replaces Ford part number D0OZ-17C583-A.

Used Dash to Gauge Feed Harness for the 1973 Mercury Cougar and Ford Mustang with either the 351C-2V or 351C-4V, Cleveland engine only. Also bundled with the wires is the air conditioning clutch wire and carburetor solenoid wiring? Used condition, tested and working, professionally repaired, normally these are hard from engine heat. Replaces Ford Part #: 14289Check out the video below on our new gauge tester: ...

D1ZZ-15525-A 71 72 73 Mercury Cougar and Ford Mustang with the factory installed Hurst shifters. Plugs into the backup lamp switch and connects to the harness plug on the firewall behind the engine.

Used wiring pigtail that runs from the under dash harness to the radio on the 71 - 73 Cougar.

Used wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...