Your cart is empty!
Swivel that mounts to the lower clutch rod or clutch adjusting rod. Original Ford part number D0ZZ-7A528-A.
(7526) Nylon plastic injected. Correct original design. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these.Replaces Ford Part #: C0AZ-7526-B.Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they...
Includes: 2 Lock Nuts 1 Spacer 1 Retaining Clip Fits the 1968, 1969, and 1970 Mercury Cougar with the 390GT, 428CJ or the 428SCJ. Replaces Ford Part #: C8ZZ-7521-BR. Can be used on 1967 3 or 4 speed cars with 390 engine, but must use the 1968 clutch fork, see item 13882.
Lower clutch rod and adjusting nuts to ensure proper clutch operation. For the Boss 302 and 351. Unless you have your original swivel, also see item 11773. This part goes between the nuts. Replaces Ford Part #: C9OZ-7521-A.
Nice reproduction of the original. Replacement Z-Bar for 1969 and 1970 351W engines with either 3 speed or 4 speed manual transmissions. Replaces Ford # C9ZZ-7528-A.
Nice reproduction of the original. Street name is Z-Bar.
For all 1967 - 1970 FE engines 390 and 428CJ.
Replaces Ford part #: C7ZZ-7528-B.
Clutch equalizer pivot mount, engine side. Zinc plated. Replaces Ford part #: C7ZZ-7A572-BR.
Mounts on frame for equalizer bar to ride on. Replaces Ford Part #: C5ZZ-7507-A.
Replaces Ford Part # : C7ZZ-7507-B
Replaces Ford Part # : D0OZ-7583
Made of heavy gauge steel with a satin black painted finish. Replaces Ford Part #: C9ZZ-7535-A.
(7521) Correct contour insures a good fit, 12 1/2" long. This is for both 3 and 4 speed cars. Check out the comparison picture with the off-shore crapola rod sold by most vendors. The only reason you replace this rod is that it is wore down in the area where the bushing seats. Unfortunately when the Chinese were given a sample to copy they must have been given a worn out one! The one on the left (made in USA) fits tight with the bushing and was copied from a NOS sample. Replaces Ford Part #:...
(7521) Correct Contour and fit. Connects pedal to Equalizer bar. Fits all engine sizes 3 and 4 speed. Replaces Ford Part #: C9ZZ-7521-C.
Clutch Lever Dust Boot for the 289, 302 and 351. Replaces Ford Part #: C6OZ-7513-C.
This reproduction is made from the original Ford tooling and is new to the market. Well worth the few extra dollars over the previous ones offered. Replaces Ford Part #: C6OZ-7513-A.
Fits the 1967, 1968, 1969, 1970 and 1971 Mercury Cougar with the 390, 428, 428CJ, 428SCJ, 429CJ or 429SCJ. Replaces Ford Part #:C8OZ-7B535-AR
Replaces Ford Part # : C9ZZ-7591-A
This great little kit replaces stock Ford bushings that can wear out in as quick as one year. This is a very simple repair and upgrade, once you have removed the pedal support from the car. Upon completion of this you will be rewarded with greatly reduced pedal pressure and the knowledge that you will never have to replace these bushings again. This is a must have for anyone with a manual transmission.Does not fit 1971-73 Mercury Cougar or Ford Mustang.
Reproduction Clutch Pedal Rod To Firewall Seal. Replaces Ford Part #: C6OZ-7533.*NOTE* From personal experience we have found these do not stay attached to the firewall as well as the originals. An adhesive will remedy this problem.
Fits the 1967, 1968, 1969 and 1970 Mercury Cougar with the 390, 427, 428CJ or 428SCJ. These have the correct 20 coil spring, but are 1/8" longer than the Ford Master Parts Catalog calls for. Replaces Ford Part #:C7ZZ-7591-AR.
Reproduction clutch pedal return spring, comes complete with two new nylon bushings. Replaces Ford Part #: C8OZ-7534-B.
Used clutch pedal return spring with two original nylon bushings. Ford Part #: C8OZ-7534-B.
This spring is commonly missing or broken. Plated to prevent rusting and premature failure. Connects from the top of the equalizer bar to the firewall. Close Reproduction. Slightly longer and softer than our concours spring. Replaces Ford Part #: C9ZZ-7523-A.
Fits the 1969 and 1970 Mercury Cougar with the 390GT, 428CJ or 428SCJ. Replaces Ford Part #: C9ZZ-7523-B.
Fits the 1969 and 1970 Mercury Cougar with the 302, Boss 302, 351 Cleveland or the 351 Windsor. Stiffer and 1/8" shorter than our other reproduction. Replaces Ford Part #: C9ZZ-7523-A.
Fits 1968 (mid year change) through 1976 Cougar and Ford forks - All engines.Includes:1 Spring Clip2 RivetsReplaces Ford Part #: C8AZ-7B516-A.
Injection molded plastic stops underdash squeaking from clutch pedal return spring. 2 required per car. Replaces Ford Part #: C1DZ-7A630-A
C9ZZ-7528-A Equalizer bar or "Z" bar for 351 cubic inch Windsor engines and Boss 302 Eliminators with manual transmissions. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.
D0ZZ-7528-C Equalizer bar or "Z" bar for FE big block engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.
D0ZZ-7528-E reproduction Z-bar or clutch equalizer bar only for the Boss 302 Cougar Eliminator or Mustang. These are exact copies of the originals, and those used stock cast iron exhaust manifolds. There is no way to tell if this will work with headers.
D0ZZ-7528-E Equalizer bar or "Z" bar for Boss 302 Eliminators 4 speed transmissions only. This is a used part and it will most likely show some wear form previous use.
D0ZZ-7528-D Equalizer bar or "Z" bar for 351 cubic inch Cleveland engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use. See the 1969 listing if you have a 1970 351 Windsor engine.
Bushings for the clutch equalizer bar, ball pivot for 1967 through 1970 with big block engines only, sold as a pair. Replaces Ford Part #: C1AA-7543-A