Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 241-269 of 269
$0 Price: $18.55

Buy Details

Availability: In-Stock Item
Item #: 30783 -

Concours rear axle vent hose for any 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Rubber hose that attaches to the metal nipple on the top of your rear axle housing. Fits 8 and 9 inch rear ends. Includes hardware as shown. Crimp clamp, screw clamp and bolt. Ribbed hose like original, and has yellow paint mark like from the factory. About 20 inches of hose is included, a little more than what was from the factory. Part number 4A001 in the chassis assembly manual.

$0 Price: $0.85

Buy Details

Availability: In-Stock Item
Item #: 41343 -

#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.

$0 Price: $929.88

Buy Details

Availability: Out of Stock
Item #: 24539 -

Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Bare housing with proper axle pad spacing, vent location, and brake line attaching. For all 1968 big block Cougars. Over-sized shipping length. Ford part # C8ZZ-4010-C. Axles needed: Passenger side - 31-1/8 inches long, Driver side 27 inches long. *Tip* If you are looking to strengthen your 1967-68 Cougar or Mustang with a 9 inch rear end, consider buying our used assembly from a 1969 or 1970....

$0 Price: $1,000.04

Buy Details

Availability: Out of Stock
Item #: 31371 -

Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Bare housing with proper axle pad spacing, vent location, and brake line attaching. For all 1968 big block Cougars. Over-sized shipping length. Also has little differences in the housing early to late. Feb 1968, the brake hose mounting hole moved for staggered shocks, for use with 4 speed 428CJ's. Ford part # C8ZZ-4010-C. Axles needed: Passenger side - 31-1/8 inches long, Driver side 27...

$0 Price: $1,199.88

Buy Details

Availability: Out of Stock
Item #: 24268 -

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Rear axle assembly - Housing, Axles, brake backing plates, and third member. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. 1967 early 9 inch rear end housings had the carry over fill plug in the steel housing as seen from the back of the car. As removed from West Coast Cougar organ donor car. We recommend a bearing...

$0 Price: $1,129.86

Buy Details

Availability: Out of Stock
Item #: 24538 -

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. First year for the oil fill plug in the cast third member. Also has little...

$0 Price: $1,200.02

Buy Details

Availability: Out of Stock
Item #: 27513 -

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. 1967 late 9 inch rear end housings without fill plug in the steel...

$0 Price: $890.01

Buy Details

Availability: Out of Stock
Item #: 31372 -

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. First year for the oil fill plug in the cast third member. Also has little...

$0 Price: $849.87

Buy Details

Availability: Out of Stock
Item #: 24842 -

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. As removed from a 1969 West Coast Cougar organ donor car. We recommend a...

$0 Price: $225.86

Buy Details

Availability: Out of Stock
Item #: 30652 -

D0OZ-4204-9A300 1968-1973 9 Inch Third Member - UsedAlso called a pumpkin, 3.25:1 open ratio. These 3rd members will have the fill plug and 28 splined axles.Check your door tag under "Axle".

$0 Price: $225.00

Buy Details

Availability: Out of Stock
Item #: 30653 -

Also called a pumpkin, 3.00:1 locking ratio.Check your door tag under "Axle".Please note, that this is a vintage, two pin equa lock third member. Most of us should be looking at a modern design traction lock for spirited driving. The 1960's Equa-Lock, is pretty weak.1967 code A 1968 code E

$0 Price: $292.86

Buy Details

Availability: Out of Stock
Item #: 24174 -

1967 - 1969 390-4V engines with 3 or 4 speed manual transmissions. 1969 - 1970 Boss 302 Eliminator 4 speeds. 1970 M-code with 3 or 4 speed manual transmissions. Shaft diameter 3 inches, length 53-1/32" measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.

$0 Price: $275.85

Buy Details

Availability: Out of Stock
Item #: 25360 -

351CJ denoted by a Q in the 5th position of the VIN. All automatic equipped Cobra Jets came with a C6 transmission. Shaft diameter 3-1/2 inches. Length 50-13/32 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Shipping is oversized due to length.

$0 Price: $468.86

Buy Details

Availability: Out of Stock
Item #: 24484 -

1968 - 1970 428CJ Drive shaft - Used All 428CJ's with 4 speed manual transmissions. Shaft diameter 3 inches, length 53 inches measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.Ford part # C8WY-4602-A.

$0 Price: $314.87

Buy Details

Availability: Out of Stock
Item #: 25361 -

429 Cobra Jet and top loader 4 speed transmission. Shaft diameter 3 inches, length 53-13/16 inches measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.

$0 Price: $358.88

Buy Details

Availability: Out of Stock
Item #: 24486 -

428CJ engines with C6 automatic transmissions. Shaft diameter 3-1/2 inches. Length 49-41/64 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.

$0 Price: $248.85

Buy Details

Availability: Out of Stock
Item #: 25145 -

Select 1970 M-code 351-4V engines and FMX transmission.Shaft diameter 3-1/2 inches. Length 53-9/16 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Not a common part, currently out of stock.Ask about slip yokes. Shipping is oversized due to length.

$0 Price: $44.87

Buy Details

Availability: Out of Stock
Item #: 25816 -

D0ZZ-5493-A Rear sway bar bushing with 1/2" diameter opening. Used on rear anti-sway bar on the 1970 Eliminator and 70 - 73 models ordered with the competition handling package. Casting number as seen on the bushing is D0ZA-5484-E. Sold individually.

$0 Price: $36.86

Buy Details

Availability: Out of Stock
Item #: 25082 -

These are the U-shaped brackets that hold the round part of the rear sway bar. These mount to the rear frame rail. All 1970 - 1973 Cougars should have these mounting holes from the factory, 1969 and earlier Cougars do not have these holes. Two clamps needed for installation.

$0 Price: $21.85

Buy Details

Availability: Out of Stock
Item #: 10234 -

Reproduction mounting bracket. This is the mounting plate for the end links on the factory rear sway. Mercury Cougar 1970-73 only, this is not a Mustang part. The tab for the end links are mounted forward of the rear axle towards the outside of the car. These plates get sandwiched between the shock mounting plates and the Isolator clamps on your rear axle assembly. Sold individually and you will need two for the installation. Left is the same as right. The total width of this plate at its very...

$0 Price: $75.87

Buy Details

Availability: Out of Stock
Item #: 25147 -

This is the mounting plate for the end links on the factory rear sway bar. The tab for the end links are mounted forward of the rear axle towards the outside of the car. These plates get sandwiched between the shock mounting plates and the Isolator clamps on your rear axle assembly. Sold individually and you will need two for the installation. Left is the same as right. The total width of this plate at its very widest part is 7 7/8". Found on all 1970-73 Mercury Cougar with factory competition...

$0 Price: $41.27

Buy Details

Availability: Out of Stock
Item #: 16185 -

Used mounting bracket. This is the mounting plate for the end links on the factory rear sway bar. The tab for the end links are mounted forward of the rear axle towards the outside of the car. These plates are mounted with the shock mounting plates on your rear axle assembly. Sold individually and you will need two for the installation. Left is the same as right. Replaces Ford part number D0ZZ-5A775-A.NOTE: These are only a few of these in stock, and they will have moderate pitting.Mustang...

$0 Price: $69.89

Buy Details

Availability: Out of Stock
Item #: 30532 -

Used pinion yoke for an 9 inch rear end on any 1967-73 Mercury Cougar or 1967-73 Ford Mustang. 1310 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3AZ-4851-L.

$0 Price: $299.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32931 -

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. This economy version of our 8 inch rear end assembly is perfect for those intending to add rear disc brakes to their car.  Spring perches are 43 inches apart on center. Axle...

$0 Price: $215.87

Buy Details

Availability: Out of Stock
Item #: 25146 -

For any 1970 Cougar, part of the Competition Handling Package. Rear sway bars were standard fare on all Boss 302 Eliminators, and 428 Cobra Jets. This bar is 1/2 inches thick. Concours restorers, paint this bar chassis black and put a single Pink stripe on it. This factory used rear sway bar, does not include any mounting brackets or end link kits.Replaces Ford part number D0WY-5A772-A.*Note - will not fit Mustangs.Here's our little film to help you fortify your flexxy feline! ...

$0 Price: $499.86

Buy Details

Availability: Out of Stock
Item #: 19589 -

Complete used kit as taken off of a clean Western Eliminator or 1970 Cougar equipped with competition handling package. This factory applied paint daub was to remind the line worker that this side was the passenger side. The bolt measures 11 1/2" long total width and the spacer measures 7" long.  These are both longer than what you would find on a 1970 Mustang. The width of this plate is 7 7/8" at its widest part. ...

$0 Price: $21.93

Buy Details

Availability: Out of Stock, On Order
Item #: 11794 -

This reproduction universal joint fits the differential end of the drive axle and is used on all Mercury Cougars or Ford Mustangs equipped with the 289, 302, 351 Windsor as well as most 351 Clevelands (see chart). Includes a grease fitting for extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

$0 Price: $12.87

Buy Details

Availability: Out of Stock
Item #: 31253 -

Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73.  A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...

  • Next >