Interior

Fixed steering column from a 1968 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often brake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. Upper and lower mounting brackets, are available, but sold...

This nice used original part will have no broken tabs as seen on our grade 'B' version. This grade 'A' part will include two metal clip-on spacers as shown. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior.

This used original part will have a broken tab so you will have to use a over-sized washer or some other clever means of properly attaching it to the underside of your dash. This grade be part will not include the metal spacers seen on our grade 'A' part. Even with a broken tab this is a much better looking and fitting part than our economy reproduction. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior. ...

This is a much better quality part then what you see offered elsewhere. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior. Clips temporarily not available from supplier. No clips included at this time.

Reproduction OE spec reproduction of the two spoke steering wheel. This is the exact size and feel as the original, and has the correct factory detail Check out this video

Reproduction OE spec reproduction of the three spoke woodgrain deluxe rimblow steering wheel. This is the exact size and feel as the original, and has the correct factory detail on the spokes and center hub. Included are the wheel, gap cover and installed rimblow switch. Check out this video

Good used pad that will most likely need to be repainted unless it is black. Not hard and crispy looking. Comes naked as shown.

Good used pad available in limited colors, call for current stock on hand. We often have black and green available but hit and miss on the other colors. The center emblem is sold separate. Engineering number as seen from the backside reads D0AA-3E662-BW, Ford part number D0AZ-3623-A

Excellent quality reproduction sun visor assemblies and corner trim for the convertible 1969 - 1970 Mercury Cougar or Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. Sold as a pair, the original passenger side part has a C9ZB-7604122-C casting number on the back side and the driver side reads C9ZB-7604123-C. These will also interchange with versions ending in A B or D. Later versions will show one less screw tab. Replaces Ford part # C9ZZ-7604144 /...

Used single hole front mount center visor bracket for the 1969 / 1970 Mercury Cougar and Ford Mustang hard tops.  The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your desired color in the 'comments' section of your order. Ford part # C9AZ-6204132, casting # C9AB-6204132-B.

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Reproduction single hole front mount center visor bracket for the 1969 and 1970 Mercury Cougar or Ford Mustang. This is a decent reproduction, but not quite as nice as the originals. Reproductions only come in 'paint to suit' black but we have most original colors in used. Replaces Ford Part #: C9AZ-6204132.

For the purists out there we have a very limited amount of used visors that have no impressions, seam separation and minimal rust on the clips if any. Convertible and Coupe are the same.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually

Reproduction sun visors that are fully padded and covered with the correct textured vinyl to match the seats. These units are sold as a pair.

Support brace between the cowl top and the brake pedal support bracket. Fits 1969-70 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Ford part number C9ZB-6501554.

Support brace between the cowl and the top of the brake pedal support bracket. Fits 1970 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Overall width is right at 5-1/2 inches on the 1970, larger than the 1969 version. Ford part number D0ZB-65015A18-A.

Good aluminum piece that has no corrosion, no dings and all six mounting studs will be firmly in place. This same bezel was used on all Standard, XR7 or Eliminator Cougars for 1969 and 1970. Obviously the clock hole was not utilized on the Standard Cougar.

New Old Stock 1969-70 Mercury Cougar XR7 dash 3 pin on / off rocker switch. Suitable for any position, MAP COURTESY PANEL or ACCY. These are sold individually and in most applications four are used except in 1970 xr7 convertibles or or 1970 xr7 coupes with rear defog. In these cases a different design of switch was used and the surrounding bezel would be labeled "Top" or "Defog" in the farthest position to the right. The fourth switch is never used on the 1969 xr7, it is just there to...

1969-70 Mercury Cougar XR7 dash 3 pin on / off rocker switch. Suitable for any position, MAP COURTESY PANEL or ACCY. Switches sold pit free on the chrome. Switches guaranteed to work, but are likely stiff. Electro solvent usually helps with that sticking condition, see product label for directions prior to use. These are sold individually and in most applications four are used except in 1970 xr7 convertibles or or 1970 xr7 coupes with rear defog. In these cases a different design of switch was...

For two spoke steering wheel. Two pressure switches with connection terminals installed into black plastic holder. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part # D2AZ-13875. Fits standard or deluxe steering wheel inserts.

NOTE!!!! This offshore switch is assembled with plated steel rivet contacts as opposed to brass rivet contacts like original. Whereas the Torino or Mustang do fine with 2 incandescent rear bulbs the Cougars with 6 bulbs put too much load on the switch and they fail. The only way these switches will hold up in a Cougar is if you convert to LED. We are hoping the supplier will take our advice and correct this problem but until such time we cannot warranty this product. Don Rush 9-11-2017 1970-72...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This switch also fits the 1970-1972...

Unlike the reproduction, we have this available in multiple colors. Call for availability. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Ford part # D1ZZ-13915-A Used in conjunction with the deluxe trim plate.

This little cover glues onto your spoke at 6 o'clock and serves to cover the gap between where your rubber horn switch starts and then stops. NOTE: The 69 steering wheel does not take one of these covers because the bottom of the horn pad actually comes down far enough to cover the rimblow gap spacing.Replaces Ford Part #: D1ZZ-13875-C. Check out this video

For two spoke steering wheel, comes in black only. Exact reproduction with correct grain texture. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part #D0ZZ-13915.

Tested and working all metal 6000 RPM tachometer with correct Seat Belt and Lights indicator lenses. 1970 Mercury Cougar XR7 and Eliminator models only. Ford part number C9WF-17360-A. There is a second manufacturer (See other listing) of this 1970 tachometer which was manufactured by Faria Instruments. It is identified by having a plastic rear housing and a rest for the needle. It has a part number of C9WF-17360-A2. *Note - Boss 302 Eliminators normally received 8000 RPM tachometers.*Note -...

This tachometer was only used on the 1970 BOSS 302 Eliminator but occasionally found its way into other models. This is a tested, working original part. 70 differs from 69 only in the indicator lights at the bottom.Check out the video below on our new gauge tester: ...

Requires a $50 refundable core charge, send us your dummy plate for a core refund! No, Mercury never offered an in dash tachometer for your 1969 - 1970 Decor or Standard model Cougar... For years people have been "making" 2 wire tachometers from xr7 and Eliminator Cougars work (kind of). This is a brand new three wire tachometer custom made to look and fit like the original would of had they been available in the day.  If you would like to retain the original standard clock we now have a...

Return your core to us for a $65 refund! Three wire tachometer for Cougars. Ford wired their early (pre ‘74) tachometers so that they are part of the ignition circuit. What this means is that if the tachometer goes bad, the engine shuts OFF. It also means that you must either replace it with another series type tachometer with 35+ year old circuitry or install a jumper wire to bypass the tach. It also means that you need a special adapter to use your factory tach with an MSD ignition box. Our...

New temperature sending unit for the 1970 - 1971 Mercury Cougar and Ford Mustang with an actual temperature gauge and a 428, 428CJ (Cobra Jet) or 429CJ (Cobra Jet) engine. Replaces Ford Part #: D0ZZ-10884-A (SW-925)Check out the video below on our new gauge tester: ...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels on any 1967-70 Mercury Cougar or Ford Mustang. Additionally, it also removes the wiper switch on 1969-70 Mercury Cougar and Ford Mustang. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68, or 1969...

This is a mirror nut bezel tool used to remove the mirror nut on the 1967 - 1968 and 1970 - 1973 Cougar. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This tool pays for itself each time you use it. NOTE: This is an exact fit for ALL used mirror nuts (bezels) and the 1970 - 1973 reproduction mirror nuts (bezels). However, you will find it does not fit our 67-68 repro mirror nuts (bezels) and will need some...

Slightly wider than the 1967 version. Customer feedback at mercurycougar.net: I did a drum to disc conversion on my '68 a few months ago. WCCC sold me 2 orig. cougar brake setups from spindle to caliper to brake lines with the P. valve , you know complete.. These freaking brakes looked like they were a year old, no sh**. I had my Friend Perry from "Perry's Pony Express" a Classic Mustang restorer here on Long Island help me install them & he told me they were the cleanest 1968 used brakes...

*NOTE* 1969 - 1970 Convertible mats do not have any covering to the right of the gas tank. This is in fact how the originals were made. Many Convertible owners prefer to have a full cover mat. If that is you we suggest you purchase the coupe mat for your convertible.This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray and black plaid pattern. Do NOT confuse this with the light duty mat you will see...

This reproduction is pathetic... It is made from the same material as a cheap picnic table cloth (you know, the red checkered ones?) The only way you will ever get this plastic "table cloth type" mat to lay flat is to glue it down. They do however work well for catching oil spills under your Cougar when turned felt side up. The correct dark gray speckled pattern for 71 - 73 is not available with this mat. No returns on this product, we suggest no mat is a better alternative than this poor...

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

New heavy duty rubberized undercoating for the Mercury or Ford. Heck, it can be used on ANY car. This body shop proven formula is used to protect against road salt, moisture and corrosion. To be used on the inner aprons and fenders, frame rails, fuel tanks, rocker panels, under hoods and firewall. Basically, anything you want to protect under your pride and joy will be encapsulated and protected with this heavy duty rubberized undercoating.

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654606-A and are marked R.H. for the passenger side.

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power.

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Metal portion of the driver side rear interior panel on a LATE 1970 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels. Grade B used, will have at least...

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Metal portion of the passenger side rear interior panel on a LATE 1970 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels. Grade B used, will have at...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.