Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.
Pair of steel brake line rubber grommets for any 1969-70 Mercury Cougar or Ford Mustang. These grommets go into the shock towers. Sold as a pair. Inside hole diameter is 3/16"
Reproduction grommet that seals the check valve to the Midland brake booster on the 67 - 68 Cougar or Mustang. We also sell the grommet / check valve combo, you can find it here.
New hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Replaces Ford part number 380699-S.
NOS emergency / parking brake handle. To remove your old handle break the plastic off of the shaft to reveal the splined pin. Pull out pin with vise grips and install the new unit.
This reproduction emergency / parking brake handle is an exact reproduction that is made from quality materials and is less prone to cracking than your original. That being said, these still will crack if you pull hard and do not have your hand close to the shaft. This was a design flaw from day one. The correct way to apply the brake to reduce the chances of these handles cracking is to split your fingers around the shaft when applying the brake, keeping your fingers close to the...
Used grade "B" emergency / parking brake release handle with bezel and cable for the Mercury Cougar. This unit fits both the Standard and XR7. Our grade "B" piece may have a cracked cable sheath and the chrome on the release handle will be flaking or chipping. Ford Part Number: D1WY-2760-A or D1WY-2A760-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web...
Reproduction brake booster hose for Mercury Cougar or Ford Mustang. Measures 12" long
Reproduction hose and clamp kit for the brake booster on your 1969 Cougar or MustangDate code: 10/22/68
Reproduction hose and clamp kit for the brake booster on your 1969 Cougar or MustangDate code: 10/22/69
Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 10/22/69
Reproduction date coded hose and clamp kit for the brake booster on the 1971 Cougar or MustangDate code: 11/12/70
Reproduction date coded hose and clamp kit for the brake booster on the 1971 Cougar or Mustang Date code: 12/10/70
Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 12/15/69
Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 2/12/70
Reproduction date coded hose and clamp kit for the brake booster on the 1971 Cougar or MustangDate code: 2/12/71
Reproduction hose and clamp kit for the brake booster on your 1969 Cougar or MustangDate code: 2/18/69
Reproduction date coded hose and clamp kit for the brake booster on the 1971 Cougar or MustangDate code: 5/19/70
Reproduction hose and clamp kit for the brake booster on your 1969 Cougar or MustangDate code: 5/2/69
Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 5/2/69
Reproduction hose and clamp kit for the brake booster on your 1969 Cougar or MustangDate code: 6/18/68
Reproduction date coded hose and clamp kit for the brake booster on the 1971 Cougar or MustangDate code: 6/29/70
Reproduction hose and clamp kit for the brake booster on your 1969 Cougar or MustangDate code: 6/9/69
Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 6/6/69
Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 8/18/69
Reproduction hose and clamp kit for the brake booster on your 1969 Cougar or MustangDate code: 8/19/68
Reproduction date coded hose and clamp kit for the brake booster on the 1971 Cougar or MustangDate code: 9/9/70
Reproduction brackets to hold the junction of the steel brake line and the rubber brake hose. Mounts to the frame rail. Fits 1967 Mercury Cougar and 1965 - 1967 Ford Mustang with factory installed Kelsey Hayes 4 puck disc brakes only. These are manufactured 30 thousandths thicker to compensate for the missing flange that the originals had along the sides. Replaces Ford part numbers C5ZZ-2082-D and C5ZZ-2082-C
Used front drum brake hose bracket for any 1967-70 Mercury Cougar or Ford Mustang. Simple bracket bolts to the front aprons and holds the brake hoses stationary. Right and left side are the same.Ford part number C1SS-2082-C.
Reproduction flex brake hose clip for the Mercury Cougar or Ford Mustang.
New front drum brake hub for all Mercury Cougars equipped with front drum brakes. Pretty much fits most front 5 lug 10 inch front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only. Fits 1967-69 Mercury Cougar and 1965-69 Ford Mustang with 5 lug 10 inch drums. Several manufacturers of the front drum assemblies such as Kelsey Hayes and Bendix were suppliers to Ford over the years. Quite a bit of labor to press these out. Needs threaded studs, see related...
Used front drum brake hub for all Mercury Cougars equipped with front drum brakes. Pretty much fits most front 5 lug 10 inch drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only. Fits 1967-69 Mercury Cougar and 1965-69 Ford Mustang with 5 lug 10 inch drums. Several manufacturers of the front drum assemblies such as Kelsey Hayes and Bendix were suppliers to Ford over the years. Quite a bit of labor to press these out. May or may not have threaded studs, or...
This used emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.
Used wheel cylinder link pin. This pin protrudes from both ends of the wheel cylinder and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Fits all drum brake wheel cylinders, front or rear drum brake systems. Two needed per wheel cylinder. Sold individuallyFord part number B7A-2042-A.
Reproduction wheel cylinder link pin. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Sold individually. Ford part number B7A-2042-A.
Reproduction set of wheel cylinder link pins. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place.Sold as a set of four.
New master cylinder for the Mercury Cougar or Ford Mustang equipped 4 wheel power disc brakes. This unit can be used with the Bendix and Midland boosters. Bore size: 1" WARNINGS: Do not attempt to use a 1970 booster on a 1967-69 Cougar as failure will occur within minutes! Never bleed your brakes on a power brake car with the car running. The pedal will over extend the rod into the booster and break internal parts. This is not covered under warranty. ...
New reproduction power disc brake master cylinder for the Mercury Cougar or Ford Mustang equipped with factory power disc brakes in front and drums in the back. This unit has a 1" bore and includes a new cap and diaphragm as shown. Unlike many others you will find, this unit does not need brass line adapters to fit your factory lines, they are correctly sized, will not interfere with your shock tower and ready to bolt on. Has proper threaded line size for OEM or...
New premium reproduction tear drop power disc brake master cylinder for the Mercury Cougar or Ford Mustang equipped with factory power disc brakes in front and drums in back. Has proper threaded line size for OEM or replacement brake lines, 3/8-24 and 1/2-20. The main difference between this unit and our economy version is cosmetics, as this premium unit comes with the correct "tear drop" casting; other difference to consider are this unit has a 1" bore, instead of 1 1/8"...
Reproduction master cylinder for the Mercury Cougar and Ford Mustang equipped with drum brakes. This unit is brand new, not rebuilt, and made from high quality American made parts.
Made in the U.S.A. Includes new diaphragm and cap. Has proper threaded line size for OEM or replacement brake lines. 3/8-24 and 1/2-20. WARNING: Never bleed your brakes on a power brake car with the car running. The pedal will over extend the rod into the booster and break internal parts. This is not covered under warranty.
Reproduction master cylinder for the Mercury Cougar and Ford Mustang equipped with power drum brakes. These are brand new units, not rebuilt, and are made from high quality American made parts. WARNINGS: Do not attempt to use a 1970 booster on a 1967-69 Cougar as failure will occur within minutes! Never bleed your brakes on a power brake car with the car running. The pedal will over extend the rod into the booster and break internal parts. This is not covered under warranty. ...
This used original Bendix spacer bracket is mounted to the rear of the brake booster on the 69 - 70 Cougar and Mustang. These spacer brackets sometimes come up missing when purchased from discount booster rebuilders. If you get a booster that has a piece of plate steel and spacers in place of this stamped steel bracket, it is a go around (homemade). This plate differs from repro in that the mounting holes are the correct size and it has the correct relief spacing for the input rod dust boot....
This reproduction Bendix spacer bracket is mounted to the rear of the brake booster on the 69 - 70 Cougar and Mustang. These spacer brackets sometimes come up missing from some booster rebuilders. If you get a booster that has a piece of plate steel and spacers in place of this stamped steel bracket it is a go around (homemade). This plate differs from original in that the holes are smaller than factory so they will need to be enlarged and there is no relief spacing for the input rod dust boot...
C8OZ-2B293-A Driver side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog.
C8OZ-2B292-A Passenger side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog.
This kit includes the 4 fine threaded "T" shaped studs (with nuts) that mount the backing plate to the spindle and the plate that goes on the inside of the backing plate. These are used parts that are not damaged or corroded, taken from a Western parts car.