All Products

Used alternator adjusting arm for any 1970-73 Mercury Cougar, Ford Mustang, or generally Ford anything with 302, 351, or Boss 302 engines. This can be used on 1973 cars, Ford did switch to a different alternator bracket that tightened the alternator from the back sometime in 1973. Replaces Ford part number D0OE-10145-A, listed in the Motorcraft catalog as GY-938Also fits:Comet Montego

Used alternator adjusting bracket for any 1967 Mercury Cougar or Ford Mustang with 390 engine and without smog. Also fits Shelby GT-500.Replaces Ford part number C6AE-10145-B, or it is stamped C6AE-B

Used Alternator Adjusting Arm / 429CJ for the 1971 Mercury Cougar / 1971 Ford Mustang 

Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines. This is also referred to as the low mount alternator adjusting bracket. It has the Ford stamped casting number of C8AE-10145-B. Ford part number is C8AZ-10145-B.

1967 289 smog pump adjusting arm, casting number C6OE-9B452-A. Ford part number C6OZ-9B452-A. Application is most Ford and Mercury cars sold new in California in 1966-67. Mercury Cougar only used this thermactor pump adjusting bracket in 1967.                                          ...

1967 390 smog pump adjusting arm, casting number C7AE-9B452-A. Ford part number C6AZ-9B452-C. Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and belt alignment are the same. Click on images to enlarge.                                       The...

1968 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine), or 1969 Boss 302 (G code Eliminator engine) smog pump adjusting arm, casting number C8OE-9B452-A. Ford part number C8AZ-9B452-B, C8AE-B casting number. Bolts sold separate. *Note - Only cars with manual transmissions received thermactor emissions in 1968.

Reproduction thermactor smog pump adjusting bracket for all 1969 Mercury Cougar Eliminator and 1969 Ford Mustang with Boss 302 engines. Additionally this bracket was also used on 1968 Ford cars with 289 or 302 engines with manual transmissions. Quality made product. Replaces Ford part number C8OE-9B452-A.

Used adjusting bracket for the Thermactor air pump for the Mercury Cougar or Ford Mustang equipped with the 302 Boss engine.Ford part # D0ZZ-9B452-A, casting # D0ZE-9B452-A or D0ZE-9B452-B.

This knurled nut is located under the front slides in each corner (1 per side, 2 per car) and is used to adjust the height of the sun roof panel.

C9AZ-3D600-A Power steering pump adjusting spacer for use without air conditioning. For most 1971 Mercury Cougar or Ford Mustang with 429CJ engines.

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. This fine thread version is hard to keep in stock, consider the 1969-73 course thread version as an alternative. Check out...

This is an open style air cleaner assembly devoid of any snorkel. We send the tops out for a quality rechrome and we can inform you of what dates we have at any one time (date is stamped on bottom, 2 digits year and month, very faint). Most are happy to use the Mustang K code 289 HiPo reproduction air cleaner assembly we sell, which Mercury used on W code GT-E's with 427's. There's also a reproduction unit available.Ford part # C5ZZ-9600-C, C5ZF-9600-D. ...

This is a reproduction of the original engine displacement decal. Round decal, chrome background with gold followed by black and chrome checkerboard followed by gold background with chrome Cougar logo, followed by black and chrome checkerboard followed by black background with gold CJ 428-4V followed by black and chrome checkerboard followed by gold background with chrome Cougar logo, followed by black and chrome checkerboard. Located on the top of the air cleaner.Fits the following models...

Nice used California emissions air cleaner assembly, includes base with elbow, snorkel, heat riser and air cleaner lid. Application is any 1967 Mercury Cougar or Ford Mustang with C code 289-2V or A code 289-4V engines with closed emissions as sold in California. Elbow on air cleaner connects to the oil fill cap with a rubber hose. All good parts as shown, thermal switch in air cleaner snorkel may not work, and no we cannot test them.Even if you are not currently running all original parts...

Fits all V8s with oval air cleaner.

NOS new old stock vacuum motor, for early 1968 air cleaner snorkels. Up until about April 1968, the air cleaner snorkels were vacuum operated for the trap door going to the exhaust heat riser. Tested as working. Fits a wide variety of Ford cars in 1968. Don't forget to save the heavy washer that goes over the shaft from your old assembly. Ford part number C8AZ-9D612-A.

A Complete A/C heater control assembly that includes a bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Check back often, this type and grade of part is seldom in stock very long. Ford part # C8WA-19980-A.

A/C and heater control bezel or face plate. Grade A- used condition, standard pebble grain trim. Check back often, this type and grade of part is seldom in stock very long.Bezel only, no levers or switch.Ford part # C7ZA-19C705.

1964-66 Ford and Mercury alternator bracket with air conditioning adjusting pulley. Pulley has new bearing installed. Application is 1964-66 Ford and Mercury full sized cars and Thunderbird. All with 352, 390, 410, 427, or 428 FE engines with air conditioning and without thermactor smog. Pulley has been professionally rebuilt with new bearing in house. Pulley has a few small rust pits, that can be filled and painted by the purchaser. Pulley is straight and true, pulley has Ford casting number...

Reproduction gold dichromate 10 blade alternator fan. Used on Mercury Cougars and Ford Mustangs manufactured after 11/17/1969. Actually this is a Ford part found on most all Ford automobiles from 1970-73. 10 blade alternator cooling fan. Replaces Ford Part #: DOAZ-10A310-B

[No Description Provided]

Replaces Ford Part # D0WY-14305-C & D0WY-14305-A

Older used aluminum intake manifold. Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

New intake manifold that has never been used, but it's missing the packaging, so we're calling it an "out of box special". Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

7TPF Factory AM radio for any 1967 Galaxie or LTD models. Unknown working condition.

Used radio from a 1974 Mercury Comet or Ford Maverick. Should fit other years too. This is a mono radio, meaning that it is a single channel radio without stereo. That is the way they were built for the Maverick and Comet cars all the way back to 1970. Both the AM and FM radio bands function properly, selector buttons all work properly, comes with used knobs as shown. The only two defects on this radio are the small crack in the lens (shown in photo), and the cut electrical plug. We have...

New old stock amp gauge for the 1969 Mercury CougarFord part number C8WY-10850 Check out the video below on our new gauge tester: ...

Reproduction pair of anti rattle pad for the stone guard used on the Mercury Cougar. This unit is for the 1970 specifically and will not fit any other year. These pads must be used with the 1970 front bumper mounting brackets and the brackets can identified by the square cut window for mounting this pad. Sold in pairs and two are required per car.

Reproduction of the protector felt pad between the spare tire and jack handle for the 68 through 70 Mercury Cougar with styled steel wheels. Used only in conjunction with applications that store the jack components on top of the wheel.

WCCC developed walnut straight grain kit for rimblow horn pad restorations. Fits all Standard / Decor (non-XR-7) 1969 Cougar hardtop and convertibles. All three pieces were carefully plotted on a computer program to account for their unique contoured shape for each individual insert. Detailed instructions included for preparation and installation. We suggest detailing your horn pad plastic insert, prior to applying this wood grain kit for best results. *NOTE* Fits 1969 rimblow horn pad plastic...

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Although many would disagree, these are in my opinion average quality. "BUT" they are currently the best available reproduction. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue, Parchment, Ivy Gold, Aqua , Saddle, or Nugget Gold. Replaces Ford part # C8ZZ-6524100 and C8ZZ-6524101. *NOTE* The Ivy Gold and Aqua armrests are not correctly colored for the...

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Used driver side (left hand) rear armrest for the Mercury Cougar that is in grade A condition. Grade "A" armrests are not pulling away from their backing and have no splits, cigarette burns or other obvious defects. They may need to be painted with vinyl paint, especially since we can almost guarantee we will not have both sides in your color in stock. Please indicate in the notes which color you would prefer, we will do our best to accommodate you. *NOTE* If you have a standard or decor 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...