All Products

NOS 1983 Ford manual on how to read and understand vacuum diagrams. Although it's technically made for older cars, it has tons of useful information on how to decode diagrams. Includes sections on vacuum theory and applications, devices, hoses, schematics and system diagnosis. This handy book has information pertaining to how the engine creates vacuum, the carburetor and it's vacuum pressure regulation characteristics as well as air intake, fuel induction, emissions and ignition. As an...

New old stock, NOS, windshield wiper switch for any 1969 Cougar or Mustang. Marked C9ZB-17A553-A on the back. This is the two speed variety, the 1970 switch has a longer shaft than this 1969 version.

Miniature light bulb for any 1967-68 Mercury Cougar or Ford Mustang with the door ajar feature. Original equipment GE 256 light bulb. This is a flashing light bulb. It has a metal strip that heats up and breaks contact for a flashing effect. Starts out with the bulb on, and eventually starts flashing over a period of a few seconds.

Reproduction emblem for the 390 engine designation. Never used on a Cougar, but an attractive emblem for customizing. Measures 3 1/8" x 3/4" and has two mounting studs.Replaces Ford part # C9ZZ-16637-D.

Nice pliable original seal that measures 3 5/8" tall, no burns, rips or cuts. Will trade straight across for 68-70 428 Cougar ram air seal which is only 2 1/4" in height. Ram Airs seals are designed to stretch over air cleaner bases that are approximately 14 3/8" wide at their outer most upper lip.

Reproduction A/C evaporator for the later production 1969 - 1970 Mercury Cougar and Ford Mustang. This later version of the evaporator has inlet and outlet tubes that run diagonally of the core as opposed to the early version where the tubes run horizontally.*Note - We have had numerous customers complain that these don't fit exactly like the originals. As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies...

Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade B vents will mostly have a missing metal bracket and / or small crack or break usually around the mounting holes.

Concours correct A/C discharge hose for Mercury Cougars and Ford Mustangs.Replaces part # C7AZ-19972-A or C7ZZ-19972-A.This hose is compatible with both 134a and R12 refrigerants.

New Old Stock A/C drain hose for Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. The best part is that because this is a NOS part, it will fit right the first time and be absolutely correct!Ford part #: C7ZZ-19858-C.

Concours correct A/C sight glass hose with a 90° fitting for your Cougar or Mustang.This hose is compatible with both 134a and R12 refrigerants.

There are 2 manufacturers of these hoses and many places will call them a "concours" hose. Neither manufacturer make an exact replica of the original sight glass hose. The finish of the hose does not match, but the most obvious difference is that the sight glass itself has a hexagon shape instead of a square shape. If you would prefer a good used original, give us a call, we can usually dig one up for you. Remember to remove your coupler between this hose and the dryer, it will be need...

Decent reproduction of the air conditioning sight glass hose for the Mercury Cougar and Ford Mustang. Hose texture is not the same and the sight glass itself is different, but length and fittings are correct. If your sight glass hose is not original or you do not have the 2 piece quick disconnect, you may need to purchase the complete sight glass hose kit. For 100% correct hose, please see our good used sight glass hoses. Includes Sight Glass Hose (Ford Part # D1ZA-19837-A or...

Here is your concours correct A/C suction hose for your beloved Mercury Cougar or Ford Mustang.This hose is compatible with both 134a and R12 refrigerants.

This is actually a kit which includes 2 hoses, 2 o-rings, and a quick connect. When assembled this hose is approximately 78 inches long. The Ford Master Parts Catalog (MPC) kit number is C8OZ-19837-A.Sight Glass Hose to A/C Dryer Hose (Part # D1ZA-19835-A)Sight Glass Hose (Part # D1ZA-19837-A)Sight Glass (Part # SG3, D2AZ-19D695-BK or YF-342) 2 O-Rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316)Quick Connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6,...

C9ZZ-18A318-C New Old Stock vacuum control motor for factory air conditioning on all 1969-70 Mercury Cougar and Ford Mustang.Tested and works perfectly. Has attached extension marked C9ZA-18A318-J.

C9ZZ-18A318-A New Old Stock vacuum control motor for factory air conditioning on all 1969-70 Mercury Cougar and Ford Mustang

For 1969 Mercury Cougars and Ford Mustangs with the 351W engine. Also 1970 Mercury Cougars and Ford Mustangs with the 351W or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-3/8", a clutch diameter of 5-3/16", and an overall thickness of 1-11/16 inches. Whew, say that 5 times fast!Ford part # C9AA-2981-D.

For 1967-68 Mercury Cougars and Ford Mustangs with the 289 or 302 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 6", and an overall thickness of 2-1/16 inches. Ford part # C7AA-2981-F.

For 1971-73 Mercury Cougars and Ford Mustangs with the 351W engine manufactured after 10-26-1970. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Ford part # D1OA-2981-A. May also have part numbers D1OA-2981-AA, D1OA-2981-A1A, D1OA-2981-A1B, D1OA-2981-A2A, and D1OA-2981-A2B.

Used pulley and clutch assembly for Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-H.

For 1967-69 Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7SA-2981-A.

For 1967 - 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-11/16", a clutch diameter of 6", and an overall thickness of 1-5/8 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-J.

For 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch. Pulley diameter 6-3/4", clutch diameter 6", and an overall thickness of 2-1/16 inches. Ford part # C9AA-2981-G.

For 1971 Mercury Cougars and Ford Mustangs with the 429CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6", a clutch diameter of 6", and an overall thickness of 1-3/8 inches. Whew, say that 5 times fast! Ford Part # C9AA-2981-E.

For 1971 Mercury Cougars and Ford Mustangs with the 429CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 5-5/16", a clutch diameter of 5-5/16", and an overall thickness of 1-3/8 inches. Ford part # C9AA-2981-E1, may also have part # C9AA-2981-E2.

For 1971 Mercury Cougars and Ford Mustangs with the 429CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 5-5/16", a clutch diameter of 5-5/16", and an overall thickness of 1-3/8 inches. Whew, say that 5 times fast!Ford Part # D0VA-2981-A.

Used air conditioning vent for any 1968 Mercury Cougar or Ford Mustang with factory installed A/C. These are different than the 1967 A/C vents. For 1968 the vents detached from the main housing for safety reasons. These were meant to 'break away' in the event of an accident. These attach to the housing with a spring, spring sold separately. Grade A is in limited quantities and will have very good chrome, there will be some minor blemishes found under close scrutiny. B grade versions also...

Grade A used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Very minor blemishes, almost insignificant as shown. No extra parts included, spring is available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19C784-A Register and Bezel. (Bright Finish). Ford casting number on reverse of this piece is C8ZA-19C784. Mustang used a shorter bracket, on the reverse you can see the witness line and...

This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's too. We also stock a Grade B version that looks the part, but does not have a working check valve, and will still need a new rubber coating on the...

This A/C vacuum canister mounts to the passenger side shock tower and controls damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1971-73 Mercury Cougar, 1971-73 Ford Mustang, as well as 1970-71 Ford Torino / Fairlane and Mercury Cyclone Montego, 1970-7? Ford Maverick and Mercury Comet.Replaces Ford part # D0DZ-19A566-A.  

C9ZZ-19B888-A

Original retainer for the passenger side A/C vent on Mercury Cougars and Ford Mustangs with equipped with factory A/C. Necessary for correctly installing the upper fastener of the vent.Ford part # C7ZA-19A950-A.

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish.This reproduction A/C vent register with knobs is a perfect fit for your Mercury Cougar or Ford Mustang / Shelby. Includes all three control knobs. *NOTE* Mustang...

Passenger side air conditioning register vent with slight manufacturer blemishes. See photos for details.

Grade A used passenger side air conditioning vent register for 1967 Ford Mustang with standard (non-deluxe) interiors. This one has the factory pebble grain or camera case finish. Very nice used, only have the one available. We also have several Mustang center vents available with the pebble graining.Replaces Ford part number C7ZA-19893. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store...

This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent that was very prone to failure. This is a fixed, one piece body and will not fall apart. This will be a direct fit to your 1967 and 1968 Ford Mustang with no modification needed. Dealer pricing available. *NOTE* Mustang used the shorter version of this vent than the Cougar did, otherwise they are visually and mechanically the same. Click on images to...

Normally we do not list Mustang specific parts, but since we are the distributor for these new reproductions, we need to have them accessible via our web site to all. This kit is the same as a Mercury Cougar set with the exception that the passenger side is shorter on the Mustang / Shelby than the Cougar. Top quality chrome finish and precision fit worthy of the most scrutinized restoration. Remember when we used to spend hundreds of dollars for "decent" used examples and then take a risk with...

Normally we do not list Mustang specific parts, but since we are the distributor for these new reproductions, we need to have them accessible via our web site. This kit is the same as a Mercury Cougar set with the exception that the passenger side is shorter on the Mustang / Shelby than the Cougar. Top quality chrome finish and precision fit worthy of the most scrutinized restoration. Remember back in the day when we used to spend hundreds of dollars for "decent" used examples and or take a...

NOS 1967 Mercury accessories and factory installed optional equipment binder. This catalog was used in the dealerships to upsell customers on a variety of options available for their car. It details options from appearance, comfort and convenience, performance and other miscellaneous items such as fire extinguishers and tire chains.  This is a rare find, dealers were the only ones who were issued these binders, and this one happens to be in great condition.

C9ZZ-14A318-A-Used Wire lead for the accessory terminal found optionally on 1969-70 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire can be marked with C8OB-14A318-A or C9ZB-14A318-A.NOTE: There are two version of this wire, one is long and the other is short. The shorter version has a smaller gauge wire. ...

C9ZZ-14A318-A-Used Wire lead for the accessory terminal found optionally on 1969-70 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire can be marked with C8OB-14A318-A or C9ZB-14A318-A. NOTE: There are two version of this wire, one is long and the other is short. The shorter version has a smaller gauge wire. ...

Used Wire lead for the accessory terminal found optionally on 71 - 73 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire will be marked with D1AB-14A318-AB

This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many...

Used actuator for the seat back release on the 1970 Mercury Cougar or Ford Mustang. This item is tested and will be in working condition. Left is the same as right, two required per car. Sold individually.

This adapter is threaded on bottom for PCV valve and 6 degree angled 5/8" nipple on side. Was gold Cadmium plated, not painted. Original Ford part number C7OZ-6A706-A.

C9ZZ-3K505-A Unique for the 1969 Boss 302 Eliminator and Mustang. Flat steel bar stock spacer that positions the power steering pump a measured distance away from the cylinder head.

Adapter tube for connecting the fuel vapor purge tube to the air cleaner base. Can be either blue or black in color.

3M brand weather strip adhesive for installing the various rubber weather stripping found on Mercury Cougars on all years. This is the black colored adhesive and is the 5 ounce size.