All Available Parts - 1970 Mercury Cougar

D0WY-5A486-A. The bolt measures 9 1/2" long, the tubular spacers are 5 1/8" long. These kits are sold individually, it takes two kits per car. Yes... That mold on the bushings.

NOS fan clutch for the Mercury Cougar or Ford Mustang. This unit was used on 1968 Cougars and Mustangs that were produced before 12/1/1969 and equipped with the 302 engine. It was also used on the 1969-70 Cougar and Mustang equipped with the 351 engine.Ford part # C60Z-8A616-E

C60Z-6222454-B door handle hardware kit for 69-70 Cougar as well as select Torino / Fairlane / Cobra / Falcon

C7AZ-6571-B

D4AZ-18495-A

Sold as a set of three. Fits 1969-73 Mercury Cougar and Ford Mustang.Ford part number .

C8AZ-2B296-A

C8AZ-6223362-A. Sold individually, has a different look than our reproduction decals.

Original or NOS Ford distributor cap.

C4DZ-5415-A Sold as a pair

C9ZZ-2853-A Front emergency brake cable for all 1969-70 Mercury Cougar and Ford Mustang. Front cable attaches to the emergency foot brake. New Old Stock, measures 43-5/8 inches long.

C9ZZ-17260-A New Old Stock speedometer cable. Fits 1969-70 Mercury Cougar and Ford Mustang with V-8 engines and 4 speed manual transmissions. Over all length 69 inches. *Note - Excludes 3.91 and 4.30 ring and pinion ratios with gear reducer.

D2AZ-6522050-A Service replacement ignition and door lock set with keys. Fits 1970-72 Mercury Cougar and Ford Mustang as well as most all other Ford and Mercury car lines. *Note - Ignition lock cylinder is for system on steering column only.

C9WY-65405A86-A Used on all fuel doors 69-70 except 1970 Eliminator.Don, Received the fuel door crest. Absolutely beautiful. These NOS parts are SO COOL! I really needed this to compliment the stainless steel NOS trunk lid trim I got from you. The two make a world of difference when viewing the car from behind. I will be in touch with any future requirements. Thanks for all your help over the last few years.Mike Vardion

New Old Stock NOS lower gas door trim for any 1969-70 Mercury Cougar. Current trim part is NOS out of the box, without fasteners. Ford part number C9WY-65405-A, casting number C9WB-65405A96-A.

New Old Stock XR7 hubcap / wheel cover for the Mercury Cougar. There were two versions of this cap, one with a white painted ring around the center, and one with black around the center. The white version was used in 1969, with the black version being used in 1970. Ford part # D0WA-1130-A

Very rare to find NOS these days! Very limited supply...Add Ford part Number C9LY-6522666-A2A

Original NOS shroud with correct chocolate brown color and texture as what came on your Cougar the day it was made. The later shrouds sold by Ford were smooth, black and the "Barnum Fibre Co. Inc." maker lettering was faint. This is a wonderful piece for that concours quality 1969 BOSS 302 Eliminator or GT350 Shelby.Ford Part number C9OZ-8146-A

This listing is for a 3 bolt type upper ball joint, NOS, original Ford Service replacement upper control arm assembly. We have a very hard time keeping these in stock but we keep the listing up as it is good for comparison sake when considering the differences between reproduction and OEM. Keep in mind, service replacement parts often differ slightly from what actually came on the car. Over the years tooling is often replaced or modified and suppliers of things like fasteners often change....

Rare find, must have for your Concours Cougar. Sold individually.Ford part number C5ZZ-1012-BFits the following models with Styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang

The 1970 front marker lights are different from 1969 in that they have a fluted or distorted lens, the 1969 is clear. Ford part # D0WY-13208-A for the passenger side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on...

Will show at least a small amount of pitting. Casting number as seen on the back reads D0WB-652803-E.

Very rare find in the original service replacement boxes dated 10-07-75. Sold as a pair.Ford part # C8WY-65502B20-A.Click on images to enlarge. ...

NOS heater cable for 1969 - 1973 Cougars or Mustangs that are not equipped with factory air conditioning.Ford Part #: D1ZZ-18518-A

Here's the original "stereo" decal for the 69 - 70 door speaker grills. If you want to keep your car as original as possible, these are for you. These decals are made from aluminum, and as you know, they can get pretty flimsy after 45 years. We'll do our best to pick out good ones for you. You can get the sticker repro version here. SOLD INDIVIDUALLY. ...

Die cut vinyl decal in black. Measures 6 3/4" X 2 1/2". Adhering this decal to either the inside or outside of the glass will dictate whether it is a right or left facing cat. Check out this video

This rare accessory was only offered over the counter, it was not available as a factory option. Great upgrade for the 1970-1973 Cougar owner as cruise control was discontinued after 1969 and not offered again until 1974 on the Mercury Cougar.Ford part number C8OZ-9B742-AClick on images to enlarge. ...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

New small black tote that is made from high quality felt backed vinyl and features the walking cat logo for the Mercury Cougar. This tote measures 17" X 8" X 8" and has heavy duty stitching for improved longevity. It goes great with our trunk mats and tire covers and is great for your small tool kit or a compliment of car cleaning / detailing products. Another great product made right here in the good ol' USA!

Single cylinder head from 1970-71 Mercury Cougar with M code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 62.8 cc's. These are considered 'Closed Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 10.7:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0AE-N. 4V in the...

This poster is a meticulous recreation of the 1968 original that Lincoln-Mercury dealerships had on display in their showrooms to advertise the Cougar XR7-G. We were able to have an original poster professionally scanned, the images were restored, and the text carefully recreated to match the original. The result is a fresh new version of a rare, iconic display piece.This poster is the same size as the original, an impressive 36" x 48", and printed on nice heavy stock. If you don't have that...

This poster is a meticulous recreation of the 1968 original that Lincoln-Mercury dealerships had on display in their showrooms to advertise the Cougar XR7-G. We were able to have an original poster professionally scanned, the images were restored, and the text carefully recreated to match the original. The result is a fresh new version of a rare, iconic display piece.This 24" x 36" poster is smaller than the original, which was a massive 36" x 48". This makes it easier to display, and easier...

Fuel pump drive eccentric for most big block Ford engines 1963-70. Including 352, 360, 390, 410, 427, and 428. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 3-3/8 inches in diameter. Ford part number C3AZ-6287-A.

This sound deadener is comprised of one layer of tar sound deadener and a layer of Jute. Here is a shot of the original sound deadener pulled (slightly) apart to expose the en-capsuled insulation.  This new OEM style sound deadener is very similar, but is lacking the extra layer of tar on the bottom.  This can be overcome by adding the tar only kit to this kit.  This combination will come by far the closest to OEM than any other kit available! ...

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Used Grade "A" condition floor mat set for the 67 - 73 Cougar. Front and rear set.Ford part numbers:Two Piece Front - C7WY-6213056Two Piece Rear - C5ZZ-6513106

Reproduction license plate frame for your Mercury Cougar.  Sold individually. Note: These will not clear on the rear pull down fuel door on the 1967- 1968, so they will only work for the front license plate on the 67-68 Cougar. These can be used for front or back on the 69-73 Cougar.Check out this video of our 2013 Open House event. Se you next year! ...

D0ZZ-7210-B Chromed "Hurst" labeled shifter for all 1970 - 1971 Mercury Cougar and Ford Mustangs with factory installed 4 speed transmissions. Tough part to find loose, most will be attached to the correct vintage Hurst Competition shifter mechanism. The 1970 Ford master part number is D0ZZ-7210-B, 1971 is D1ZZ-7210-A. These shifters originally came with the "Hurst" T handles installed. These shifters will not come with a "T" handle. Check out our video on rebuilding your shifter below: ...

D0ZZ-7400-A 3 Speed manual transmission shift control assembly for any 1970 Mercury Cougar or Ford Mustang. Check out our video on rebuilding your shifter below: ...

D0ZZ-7400-A3Assembly Factory 3 Speed manual transmission shift control assembly for any 1970 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 351-4V engine. Check out our video on rebuilding your shifter below: ...

D0ZZ-7400-D Hurst built 4 speed manual shift control assembly for any 1970 - 1971 Mercury Cougar or Ford Mustang. Check out our video on rebuilding your shifter below: ...

Used Hurst built 4 speed manual shift control assembly for the Mercury Cougar or Ford Mustang equipped with the manual transmission. This assembly includes the shifter mechanism, shift rods, and shift lever. The Ford MPC states that this same shifter was used on all V8 Mustangs and Cougars. This unit may be used for the 1971 edition and is in good used condition.Ford part # D1ZZ-7400-B. Check out our video on rebuilding your shifter below: ...

Good used single sheave pulley for the alternator on the Boss 302. Ford Part #: C5AF-10A352-H.

Reproduction gold dichromate 10 blade alternator fan. Used on Mercury Cougars and Ford Mustangs manufactured after 11/17/1969. Actually this is a Ford part found on most all Ford automobiles from 1970-73. 10 blade alternator cooling fan. Replaces Ford Part #: DOAZ-10A310-B

Used wiring harness for any 1970 Mercury XR7 convertible. Connects the dash switch panel, and the intermediate or jumper lead. This harness is unique to 1970 XR7 convertibles. Has the four plug connectors as shown for the switch panel.Ford part number D0WY-10B923-B.* Note - 1970 XR7 only, body code 76B.

D0AE-9430-B 351-4V Cleveland factory original cast iron exhaust manifold for passenger side. At some point there may have been a D0AE-9430-G casting number used, which may be substituted as per the Master Parts Catalog. Same manifold 1970-1973. *351C-4V exhaust manifolds only match up to factory 4V intake manifold ports and some aftermarket aluminum intakes such as offered by Weiand and Edelbrock.

Cast iron construction similar to the 1969 bracket but with a design change for 1970. We suspect that the change was made for the new pulley and bracket arrangement starting in 1970. Ford part number D0ZZ-9B450-B.

Used adjusting bracket for the Thermactor air pump for the Mercury Cougar or Ford Mustang equipped with the 302 Boss engine.Ford part # D0ZZ-9B452-A, casting # D0ZE-9B452-A or D0ZE-9B452-B.

1970 Boss 302 Eliminator (G code engine). 3 Bolt smog pump pulley. Ford part number D0ZZ-9B447-A.

Single cylinder head from 1968-70 Mercury Cougar with 428CJ engine with smog holes. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.09 and 1.65 inch valves, and the chambers measure out at 73-76cc's. With stock pistons, these heads will net an approximate compression ration of 10.6:1. Basic cylinder head number is 6090. These are the Cobra Jet exhaust manifolds with 16 drilled and tapped exhaust bolt holes. We won't have these in stock...

Original equipment 4 speed top loader transmission from a 1970 Mercury Cougar with engine code H 351-2V, engine code M 351-4V, and engine code G Boss 302 Eliminator only. Transmission code 5 on the door tag, this would be a wide ratio 4 speed transmission with a 2.78 ratio first gear.Ford part # D0ZZ-7003-D. Casting #'s RUG-AV or RUG-AV1.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for...

Original equipment 4 speed top loader transmission from a 1970 Mercury Cougar with engine code H 351-2V, engine code M 351-4V, and engine code G Boss 302 Eliminator only. Transmission code 6 on the door tag, this would be a close ratio 4 speed transmission with a 2.32 ratio first gear.Ford part # D0ZZ-7003-E. Casting # RUG-AW or RUG-AW1. Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for...

Original equipment 4 speed top loader transmission from a 1970 Mercury Cougar with engine code Q 428 Cobra Jet. Additionally 1971 Mercury Cougar with engine code J 429 Cobra Jet and engine code C 429 Cobra Jet. Transmission code 6 on the door tag, this would be a close ratio 4 speed transmission with a 2.32 ratio first gear. The tailshaft on this transmission has a different bolt pattern for the Hurst shifter plate.Ford part # D0ZZ-7003-H. Casting numberRUG-AZ or RUG-AZ1.*NOTE* Technically...

Used OEM Ford 428 Cobra Jet manual transmission flywheel. Stamped C8OE-A. Needs a ring gear, has chipped teeth. No visible issues, no discoloration from heat. Ford 428CJ only, not for 428 SUPER COBRA JET engines. This flywheel on a 428CJ is externally balanced. Should have 184 ring gear teeth.Ford part number C8OE-6380-A.

The 1967 Cougar was Mercury's attempt to enter the Pony Car market segment popularized by the April 1964 introduction of Ford's Mustang. Introduced in the fall of 1966 for the 1967 model year, the first-year 1967 Cougar exceeded all sales expectations with 150,893 units sold. It was selected as Motor Trend's 1967 Car of the Year. Legendary Cougar Magazine is dedicated to the first three generations of Mercury's luxury Pony Car. Each bi-monthly issue includes features on the first-generation...

Door Tag Trim Code: 6A. Black XR7 Vinyl Upholstery kit to cover the rear seat for the convertible.

A few Eliminators came with standard interior, but convertibles did not come factory with a standard interior. These sets feature horizontal stitching and correct grain of vinyl. Below is a set of pictures of this set stretched on a bucket seat frame.               ...

This rubber steering coupler for your fixed column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. This is a multi-fit part that covers many years of FoMoCo products, so you will have a couple of parts left over upon completion. Will require a grinder to remove from your old steering coupler fittings. Replaces factory steering coupler on 1967 - 1973 cars. Early 1967 Mustangs do not have coupler on fixed columns. Replaces Ford part #...

Core FMX Transmission valve body for any 1970 Mercury Cougar or 1970 Ford Mustang with code "X" transmission code on the door tag. This is only for 1970 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is the...

New Permatex RTV gasket dissolver, good for all makes, models, and years. Use this stuff when you want to remove any remnants of those old worn out silicone gaskets made with any of the common gasket makers. Handy item to have on hand so you dont have to keep using your putty knife or screwdriver! 

Assembly line used engine lift hook. Passenger side 1969-70 with 428 Cobra Jet engines, including 428SCJ. Triangle shaped, with one single hole for the hook. Not stamped with number. Fits all 1968-70 Ford cars with either R code or Q code 428 engines. Cougar, Mustang, Cyclone, Torino, Talledega, Cobra, Fairlane, Montego, Ranchero etc. Attaches to the passenger side exhaust manifold. There is also a driver side engine lift hook, see related items. 

1970 Mercury Cougar and Ford Mustang convertible clear glass for the passenger side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. *NOTE* Vertical chrome trim not include. Air conditioning cars were...

Reproduction fuel bowl fitting for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All steel fitting, two needed per carburetor. Sold individually. Check the threads in those Holley bowls prior to installation, often times the bowls are bad.

C9ZA-18C366-A lower heater duct to floor outlet for Cougars or Mustangs without air conditioning. Used grade "B" part that will have more than one minor defect. It will have a small crack and possibly a broken or missing tab. Almost half the price of the grade "A" piece and works awesome if you don't have one at all. Want to have directed heating, we've got you covered.

Shaft or rod for the heater core damper door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C9ZZ-19C774-B.*Note will not work in 1967-68 A/C boxes. ...

Metal fan wheel or squirrel cage for any 1969-70 Mercury Cougar or Ford Mustang with heater only. Dimensions 4-3/4 inches in diameter and 2-1/2 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.

C9ZZ-18A651-B Complete heater and power ventilation system control assembly includes bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. The power ventilation system was a pretty rare option for 1969-70. It included a center dash register as found on air conditioned cars and directed cool air through the center of the dash. Dearborn cars would have a code "VS" on their body buck tags, and Metuchen...

C9ZA-18490-A, windshield defroster nozzle to vent for any 1969 - 1970 Cougars or Mustangs without air conditioning. This part is used and is grade "A."  If it does have any minor defects, it will have only one. It might have a small crack, but will not have any broken or missing tabs. If you drive your baby when it is cold and don't have this part, you want it. Why, because it's lame when you have to use your sleeve to wipe off your windshield to see where you are going. It's also a heck...

windshield defroster nozzle to vent for any 1969 - 1970 Cougars or Mustangs without air conditioning. This used grade "B" part will have more than one minor defect. It will have a small crack and possibly a broken or missing tab, but it's a heck of a lot better than wiping your windshield with your sleeve.Replaces Ford part number C9ZA-18490-A.

These are reproduction heater hose grommets for the heater hose to pass through the firewall. Most of the firewalls that we have seen have a flared opening for the hose without a grommet. These are a more dense rubber than our other versions. Still not sure that they are needed?

This 1969-70 Mercury Cougar and Ford Mustang shield, was installed at the factory to protect the heater motor from being damaged when the Big Block 390 / 428CJ's were being dropped in. As noted in the factory assembly manuals we sell, they were supposed to be removed once the motor was in place. We have found that more often than not they were left in place as it was probably too time consuming to remove them. Technically they should not be in place on a concours car but practically...

Concourse correct 90 degree heater hose elbow that attaches to the intake manifold and provides proper clearance for the emissions canister and air cleaner housing. Correct for all Boss 302 and 428CJ engines 1969-70.Ford number C9ZZ-18599-A.

Concourse correct 351 2bbl engine heater hose connector with a 90?� degree elbow that attaches to the intake manifold. Product discontinued by manufacturer. Know anyone else reproducing these? Let us know!

Dual heater hose tube assembly for the 1970 Mercury Cougar and Ford Mustang with the 428 Cobra Jet or 428 Super Cobra Jet engine. This heater hose attaches along the top of the passenger side valve cover. Length of long end: 13 3/8" Length of short end: 8 5/8" Replaces Ford Part #: D0ZZ-18B402-A.

This unit mounts on the main air chamber, it opens and closes the air vent. NOS or new old stock.  This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Tested and working, Ford box.Replaces Ford part # C6OZ-18C311-A. ...

Used mounting bracket from a 1969-70 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. Same bracket at 1967-68, but with a longer stud.

Reproduction grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. Made from closed cell foam, as opposed to the originals being rubber.* Note - Used starting during the later part of 1969. Compare the evaporator line orientation for both years.

Heater door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater door allows air to pass over the heater core in the A/C box. This is the smallest door in the A/C box, and the one subject to the most damage from moisture. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only,...

This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's too. We also stock a Grade B version that looks the part, but does not have a working check valve, and will still need a new rubber coating on the...

These are getting so hard to find without a broken drain cock or rust in the metal lips. We have a few single halves if you need the half without the drain cock. Soon we will have every single internal and external part from this assembly listed here, in the mean time give us a ring for those obscure parts! Two versions for 1969-70 Mercury Cougar and Ford Mustang. Difference is the evaporator and the orientation of the tubes. Look for the triangle shaped rubber line seal for the later 1969-70...

Reproduction A/C evaporator for the later production 1969 - 1970 Mercury Cougar and Ford Mustang. This later version of the evaporator has inlet and outlet tubes that run diagonally of the core as opposed to the early version where the tubes run horizontally.*Note - We have had numerous customers complain that these don't fit exactly like the originals. As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies...

This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.

Used timing chain cover from a  351W or Windsor engine from 1969-70 Mercury Cougar and Ford Mustang or most any 1969-70 Ford with 351W. Honestly, we have found that most of the 1969 production year came with the C8AE-6059-A timing cover. Cast aluminum construction without excessive damage. Installation bolt kits also available. The C8AE-6059-A timing cover can be used on 1970 302 and 351W engines, as long as you use the 1970 timing pointer. The 1970 timing pointers use alternate...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming process as a superior quality core. You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

Rear package tray defrost or defog grille. Fits all 1968-70 Mercury Cougar and Ford Mustangs with the rear defogger option. All of them were black in color. Later they were available in colors. We also have blue available, see our related tab. Replaces Ford part number C8AZ-18C490-B.

Rear package tray defrost or defog grille. Fits all 1968-70 Mercury Cougar and Ford Mustangs with the rear defogger option.Typically you only see black grilles. Later they were available in colors. We have this blue available. Replaces Ford part number C8AZ-18C490-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to...

Used wiring harness that goes from the rear of the dash all the way to the blower motor in the package tray. This same wiring was used on all 1969-70 Mustangs and Cougars. 1970 Cougar XR7 models have a slightly different configuration, but utilize the wire harness.Replaces Ford part number C9WB-18C394-A.

Rear defog conversion kit for most 1969-70 Mercury Cougar and all 1969-70 Ford Mustang Coupes. Includes hang down switch with wiring, long harness to blower motor, and blower motor and grille cover which installs in the rear package tray. Please see your electrical schematic for connection details. Excludes 1970 XR7 models, those cars had the defog switch integrated into the XR7 switch panel. This set up can easily be installed into a 1969 XR7 as well. You may need to purchase an accessory...

Used switch for the rear defog or defogger fan on any 1969 Mercury Cougar, 1969 Standard Cougar, and 1969-70 Mustang coupe or hardtop. Original switch with attached wiring harness. Tested and working two speed switch. Comes as shown with chrome knob marked "DEFOG". Some examples may have minor pits in the chrome knob. Wiring marked C9WA-18C498-A. Excludes all convertible models and Mustang fast backs.Replaces Ford part number C9ZZ-18578-A.*Note - is not technically correct for 1970 Mercury...

New Dark Argent spray paint for the 69-70 Cougar or Mustang. This paint is designed for the 70 Mustang Mach 1 grille and rocker panels, but is a great match for the argent color on your Styled Steel Wheels.

Used plug and wiring pigtail for the brake light warning switch located on the drum or disc brake distribution block mounted to the driver side fender apron. This is a plug and section of wire for repairing the underhood harness. Works on late 1970 - 1973 Cougars and Mustangs. The only difference between the late and early pigtail is that the late plug is white and the early plug is black. No difference in wiring.

New old stock Bendix master cylinder for 1968-69 Mercury Cougar and Ford Mustang with factory power disc brakes. This is a Bendix manufactured MC with proper 2227161 number and stop bolt on the bottom. Also has the dimple forward of the front brake line.  Includes a new cap with diaphragm as shown. The cap is not assembly line correct as this is a service replacement part.*Note even though this is a brand new unit, it should be tested for leaks prior to installation. Things happen when...

Reproduction front seal for the Bendix brake booster used on all 69 - 70 Cougars and Mustangs as well as many other FoMoCo products that use this size of Bendix booster. This seal prevents brake fluid from entering the booster cavity once the master cylinder fails.

This rod was used on the Bendix brand booster (crimped together case). It measures 5 3/4" long. Used on many Ford products including Torino, Cyclone, Ranchero, Cobra, Fairlane and others. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot...

Chassis black aerosal paint for all 1967-73 Mercury Cougar and Ford Mustang engine compartments. High temperature (advertised up to 350°). Manufacturer boasts resistant to cracking and flaking, chemical resistant to gasoline and brake fluid (but don't let brake fluid accumulate). *NOTE* Chemicals can only ship UPS ground only. Please, no foreign orders or USPS shipping allowed.Check out our video below on chassis upgrades: ...

This option includes paying a core charge. By choosing this option, the rebuilt booster you receive will have started the rebuild process as an average quality core.We highly recommend that you send us your core first. Here's why:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a...

As seen in our YouTube video, this is a representation of the used, rebuilt and reproduction parts that we recommend you purchase to convert to disc brakes. If you do purchase this package we will insist on speaking with you prior to shipping as you may want to substitute parts based on what year your car is, manual or automatic and what style booster you prefer. Also know that if your car already has power drum brakes we will be able to reduce the price substantially as no booster or pedal...

Reproduction pair of anti rattle pad for the stone guard used on the Mercury Cougar. This unit is for the 1970 specifically and will not fit any other year. These pads must be used with the 1970 front bumper mounting brackets and the brackets can identified by the square cut window for mounting this pad. Sold in pairs and two are required per car.

This option includes paying a core charge. By choosing this option, the re-chromed bumper you receive will have started the re-chroming process as an average quality core. We highly recommend that you send us your core first. Here's why: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming...

Used anti rattle pad for the stone guard on the Mercury Cougar. This unit is for the 1970 Mercury Cougar specifically and will not fit any other year. These pads must be used with the 1970 Cougar front bumper mounting brackets and the brackets can identified with the square cut window for mounting this pad. Our pad is sold individually and two are required per car.