Home > 1970 Mercury Cougar
All Available Parts - 1970 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 101-200 of 5133
Sorted By:
Availability:
Display Options:
Availability: Used / Wrecking Yard Item
Item #: 12297 -
Good used passenger side (right hand) moulding / trim for the Mercury Cougar that was NOT equipped with a vinyl top. These units will not have dents or deep scrapes and will be ready to install on your driver / occasional show car. Expect one or two very small dings and some scratching on the underside where glue in glass has come undone at some point. The vinyl top cars have a wider top edge but a narrow bottom edge where the non vinyl cars have a narrow top edge with a wide bottom edge....
Featured!
Availability: In-Stock Item
Item #: 13011 -
Upper and lower fuel filler door trim pieces for 1969 and 1970 Mercury Cougars, all models except 1970 Eliminator which were black. To receive core credit back your cores must have only light pitting and no broken studs. Original Ford part number C9WY-65405-A for the lower and C9WY-65405A48-B for the upper.
Availability: Used / Wrecking Yard Item
Item #: 15-0102 -
Tilt steering column cover plate for turn signal lever. Two versions, two different sizes of openings for the turn signal wand. Original used Ford part, plan on painting to match your steering column. Fits all 1970-71 Mercury Cougar, 1970 Ford Mustang, and other Ford/Mercury cars with factory tilt steering columns. Replaces Ford part number D0AA-9D793-AW.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent...
Availability: Used / Wrecking Yard Item
Item #: 15-0103 -
This item holds the release bale to the upper knuckle. It is different than the 67 - 69 clip although both can be used. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: Used / Wrecking Yard Item
Item #: 15-0106 -
This linkage fits between the gear at the bottom of the key lock and rod that goes to the ignition switch on the tilt column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: Used / Wrecking Yard Item
Item #: 15-0108 -
Used in all of 1970 and the early part of 1971. This collar uses the 'small' access plate cover. Ford master part number D0AZ-3D505-A, casting number on the part is D0AA-3D505. Nice condition, no cracks or damage. Also fits 1970-71 Lincoln MKIII and Thunderbird.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: Used / Wrecking Yard Item
Item #: 15-0109 -
Spring used to apply tension to the tilt locking pawl. 1967 thru 1969 required two springs due to the tilt away function. 1970 and later required only one spring.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: Used / Wrecking Yard Item
Item #: 15-0110 -
Spring that fits into the steering column collar. Two springs in total that hold your key lock cylinder in place. Two required per car.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: In-Stock Item
Item #: 15-0157 -
Locking pawl catch pin and locking pawl pin for your 70-73 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to these parts can avoid several hundred dollars in damage. These...
Availability: Used / Wrecking Yard Item
Item #: 15-0159 -
This linkage fits between the gear at the bottom of the key lock and rod that goes to the ignition switch on the fixed column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Ford part number D0AA-3E715-D
Availability: Used / Wrecking Yard Item
Item #: 15-0099 -
This clip clamps together the two edges of the shroud and sets into the mounting holes on the column. It is very hard to remove, and often the tab will break off very easily.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: In-Stock Item
Item #: 15-0204 -
Locking pawl pin for your 70 - 79 tilt steering column for all Lincoln - Mercury - Ford products. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to your locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to this part can avoid several hundred dollars in damage. This precision...
Featured!
Availability: In-Stock Item
Item #: 31186 -
These are BLEMISHED right and left hand set of 1/4 panel window mouldings. As you can see from the first two pictures above, these blems will have some minor bubbling or small dings in the chrome. These will be great for a daily driver if you're not worried about a few small imperfections. Some refer to these as "Hockey Sticks" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled...
Availability: In-Stock Item
Item #: 31319 -
This aluminum ninety degree bracket is what fastens the XR7 chrome boot moulding to the quarter panel. The beltline weatherstip also attaches to it. This part is only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb.You can find our reproduction pair of brackets here. ...
Availability: Used / Wrecking Yard Item
Item #: 31320 -
This aluminum ninety degree bracket is what fastens the XR7 chrome boot moulding to the quarter panel. The beltline weatherstip also attaches to it. This part is only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb.You can find our reproduction pair of brackets here. ...
Availability: In-Stock Item
Item #: 31321 -
These aluminum ninety degree brackets are what fastens the XR7 chrome boot moulding to the quarter panels. The beltline weatherstip also attaches to them. These parts are only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb.
Availability: Out of Stock
Item #: 32917 -
Reproduction passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...
Availability: Out of Stock
Item #: 32918 -
Reproduction driver side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 33054 -
Economy reproduction aluminum rear deck lid moulding / trim for the 1967 - 1968 Mercury Cougar (will also fit on 1969-1970). This reproduction is as close to the original as possible, except for the fact that the clips included have 8mm nuts, unlike the originals. There is however one small problem, the metal on these mouldings is much softer than the originals and you have to take extra care when installing the clips, if you apply too much pressure when installing, you will dimple the...
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 33053 -
Set of 4 reproduction wheel lip mouldings for the 69-70 Cougar. These are spot on and we had no problem fitting them on our cars, the only difference we noticed is that the aluminum is softer than the originals and prone to dimpling. And since they're reproductions, no cores are required! Keep in mind that when you remove your rear core mouldings, you can send them to us as they might be eligible for in store credit. For more info on aluminum trim restoration & core exchanging, check out our...
Availability: In-Stock Item
Item #: 20409 -
If you shop around you will see many places charge less than this... We have tried several different places that restore stainless trim and they all came back less than mint. These are arrow straight and have been polished to a very high luster. This trim parts will accentuate your new paint job in an incredible way!"...Don - Happy Fourth of July. I wanted to send a note to your team of gratitude for all the help they provided me over the last three years restoring my Cougar. As you know, it...
Availability: In-Stock Item
Item #: 20418 -
Restored upper left window moulding / trim for the Mercury Cougar.
Availability: In-Stock Item
Item #: 20419 -
Restored upper right rear window moulding / trim for the Mercury Cougar.
Availability: In-Stock Item
Item #: 20398 -
Restored lower left rear window moulding / trim for the Mercury Cougar.
Availability: In-Stock Item
Item #: 20399 -
Restored lower right rear window moulding / trim for the Mercury Cougar.
Availability: Used / Wrecking Yard Item
Item #: 12661 -
Good used four piece set with no dings or heavy scratches. Ready to install on your Cougar as is or polish them to a mirror like finish to be installed on a show car.
Availability: Used / Wrecking Yard Item
Item #: 20387 -
Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.
Availability: Used / Wrecking Yard Item
Item #: 20406 -
Used passenger side (right hand) upper rear window moulding / trim for the Mercury Cougar.
Availability: Used / Wrecking Yard Item
Item #: 20383 -
Used driver side (left hand) lower rear window moulding / trim for the Mercury Cougar.
Availability: Used / Wrecking Yard Item
Item #: 20402 -
Used passenger side (right hand) lower rear window moulding / trim for the Mercury Cougar.
Availability: Used / Wrecking Yard Item
Item #: 12684 -
Core stainless steel mouldings will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.
Availability: Used / Wrecking Yard Item
Item #: 12720 -
Core stainless steel mouldings will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.
Availability: Used / Wrecking Yard Item
Item #: 12710 -
Core stainless steel mouldings will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.
Availability: Used / Wrecking Yard Item
Item #: 20405 -
Availability: Used / Wrecking Yard Item
Item #: 20400 -
Availability: In-Stock Item
Item #: 33526 -
Reproduction set of 4 rear window mouldings / trim for the 69 - 70 Mercury Cougar. No core required, but keep in mind that we will give store credit for your original restorable trim!
Availability: Used / Wrecking Yard Item
Item #: 12713 -
Core grade windshield moulding for the passenger side windshield vertical stainless steel. 1969-70 Mercury Cougar and Ford Mustang coupes.Ford part number D0ZZ-6503148-B.
Availability: Used / Wrecking Yard Item
Item #: 12702 -
This driver side lower windshield moudling core is a great candidate for restoration for you do-it-yourselfers out there looking to save a buck. Or if you're driving around in a lower quality daily driver and you're missing this piece, we got what you need. Ford part number D0ZZ-6503149-B.
Availability: Used / Wrecking Yard Item
Item #: 12721 -
Used grade upper windshield moulding for any 1969-70 Mercury Cougar or Ford Mustang hardtop. Ford part number C9ZZ-6503144-A.
Availability: Used / Wrecking Yard Item
Item #: 12716 -
Because these passenger side vertical windshield mouldings are original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used "core quality" pieces. They are a great option if you have damaged or missing trim but plan to professionally restore your trim. Restorable, but not as nice as our "used" pieces. These are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503136-A. *NOTE* If you have...
Availability: Used / Wrecking Yard Item
Item #: 12705 -
Core driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang. This core grade unit is suitable for restoration or, if you are missing this piece, will fit right in with the rest of your driver quality trim.Ford part number C9ZZ-6503137-A.
Availability: Used / Wrecking Yard Item
Item #: 20431 -
Because this windshield moulding set is comprised of used original pieces, it will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well. Ford part numbers include: C9ZZ-6503136-A, C9ZZ-6503137-A, C9ZZ-6503144-A,...
Availability: Used / Wrecking Yard Item
Item #: 20389 -
Because these pieces are original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503137-A. *NOTE* If you have questions about your cores, check out our video below. ...
Availability: Used / Wrecking Yard Item
Item #: 20421 -
Because these upper windshield mouldings are used original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503144-A. *NOTE* If you have questions about your cores, check...
Availability: Used / Wrecking Yard Item
Item #: 20408 -
Because these passenger side vertical windshield mouldings are original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503136-A. *NOTE* If you have questions about your...
Availability: Used / Wrecking Yard Item
Item #: 20404 -
Because these are used original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well.Ford part number D0ZZ-6503148-B. *NOTE* If you have questions about your cores, checkout our video below. ...
Availability: Used / Wrecking Yard Item
Item #: 20385 -
Because these lower windshield mouldings are used original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly and just plain old look like crap. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well.Ford part number D0ZZ-6503149-B. *NOTE* If you have...
Availability: In-Stock Item
Item #: 20429 -
This original FoMoCo, five piece windshield trim set has been lovingly restored to far beyond the original luster. Stunning brilliance, perfect match for that high end paint job. Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well.Ford part numbers include: C9ZZ-6503136-A, C9ZZ-6503137-A, C9ZZ-6503144-A, C9ZZ-6503148-B, and C9ZZ-6503149-B....
Availability: In-Stock Item
Item #: 20384 -
Because these lower windshield mouldings are lovingly restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly and just plain old look like crap. They are an excellent option for you Mustang owners as well.Ford part number D0ZZ-6503149-B. *NOTE* If you still have questions about your cores, check out our video below. ...
Availability: In-Stock Item
Item #: 20403 -
Because these side lower windshield mouldings are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. This package is also an excellent option for you Mustang owners as well.Ford part number D0ZZ-6503148-B. *NOTE* If you have questions about your cores, check out our video below. ...
Availability: In-Stock Item
Item #: 20388 -
Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503137-A. *NOTE* If you have questions about your cores, checkout our video below. ...
Availability: In-Stock Item
Item #: 20407 -
Restored passenger side (right hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. Because this windshield moulding / trim is a restored original piece, it will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. They are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503136-A. *NOTE* If you have questions about your cores, check out our video below. ...
Availability: In-Stock Item
Item #: 20420 -
Because these upper windshield mouldings are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. This package is also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503144-A. *NOTE* If you have questions about your cores, check out our video below. ...
Availability: In-Stock Item
Item #: 27130 -
Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. This original FoMoCo, six piece windshield trim set for the Mercury Cougar convertible has been lovingly restored far beyond the original luster. Stunning brilliance, perfect match for that high end paint job. Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option...
Availability: Used / Wrecking Yard Item
Item #: 27139 -
This original FoMoCo, six piece windshield trim set for the Mercury Cougar convertible. Because these pieces are original pieces, they will have far superior fit when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well. The four upper pieces are wider than the coupe versions, but the lowers are the same (with about an inch cut off the ends). The trim is... trimmed so it will fit underneath the pillar trim pieces. *NOTE* If your trim has...
Availability: Rare / NOS Part
Item #: 27147 -
This set of NOS mouldings has been one by one taken out of the wrapper, cleaned and carefully inspected one by one for imperfections or blemishes. Even factory blemishes are not included in this show quality, pristine set. At this price you need to know you are getting the best of the best. We will allow credit for your used or core wheel lip mouldings. You can send your used or core wheel lips in prior or after your purchase and we will call and discuss what amount of credit we will allow on...
Availability: In-Stock Item
Item #: 26095 -
The four part, die cast vinyl top trim kit requires 15 (right rear under back glass is the odd ball that requires five fasteners) of these speed nut fasteners. These speed nuts also can be used on the 1969-70 Mercury Cougar XR7 dash courtesy light bezels, two for attaching that bezel to the dash pad.*NOTE* These speed nuts only work with factory installed die cast vinyl top mouldings.*NOTE* The factory nuts had a drop of silicone or trim adhesive inside the bowl that acted as a seal. This...
Availability: Used / Wrecking Yard Item
Item #: 15504 -
Good set of four die cast original top mouldings for both two tone paint Cougar hardtops and Cougars with a factory installed vinyl top. No broken studs, cracks, bends or chips. Originally these came painted and in rare cases like the 1970 Hounds-tooth edition or select two tone paint cars, those came chrome plated. These trim parts will need to be painted, Includes 15 new or used speed nuts for installation, just in case. This icon means that we're looking to buy this part!WCCC is a buyer of...
Availability: Used / Wrecking Yard Item
Item #: 24682 -
Used passenger side rear top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top. These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65424A48.
Availability: Used / Wrecking Yard Item
Item #: 24683 -
Used driver side rear top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top. These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65424A49.
Availability: Used / Wrecking Yard Item
Item #: 24680 -
Used passenger side top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top.These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65423A18-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...
Availability: Used / Wrecking Yard Item
Item #: 24681 -
Used driver side top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top. These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65423A19-A. *NOTE* Often people think these come off with a pry bar when in fact they are to be removed from the inside of the car. For some reason when people remove them they always start with the drivers side thus the premium price... This icon means that we're looking to buy this...
Availability: In-Stock Item
Item #: 41349 -
1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16
Availability: In-Stock Item
Item #: 20428 -
These trim parts (as with all our restored aluminum) feature the correct bright dip anodized plating, just as they came from the factory. If you have extra cores you would like to sell then we would like to hear from you! Please DO NOT send heavily damaged trim parts as the finished product will be delicately thin. Cores that are corroded, torn, smashed or kinked are not acceptable cores either. Please, only send cores with small dings, scratches and dullness. Extra screw holes and...
Availability: In-Stock Item
Item #: 24755 -
Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...
Availability: In-Stock Item
Item #: 18692 -
If you happen to have a set of three NOS wheel lip mouldings and purchase the fourth as a restored piece from us it will visually fit right in. Restored is never as good as NOS as the polishing process will make the part thinner which means it will be more prone to damage than an un-restored original or NOS trim part. Note! Road trash of all sorts, sand, gravel, etc. ends up in the gutter to the right hand side of the road. The front tire tends to form a vacuum and sucks stuff away from the...
Availability: In-Stock Item
Item #: 18688 -
Keep in mind you can get FREE trim parts from us if you have a quantity of good quality cores to exchange!Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...
Availability: In-Stock Item
Item #: 18690 -
These look great and because they have the correct anodized finish they will not get dull like a part that has only been polished will.Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you still have questions about your cores, check out the video below. ...
Availability: Rare / NOS Part
Item #: 18707 -
New Old Stock driver side rear wheel lip moulding for any 1969-70 Mercury Cougar.Replaces Ford part number C9WY-6529165-A, or D0WY-6529165-A.
Availability: Used / Wrecking Yard Item
Item #: 18708 -
Good used wheel lip moulding with no corrosion, obvious scratches or dents. Will have some what rough texture down low on the leading edge from road debris. This moulding will still have a good shine but do not expect NOS quality from a used piece of aluminum such as this one. When sending us a core in exchange please do not send twisted, ripped, corroded parts for an exchange. Dull, slightly dented, warped or scratched (not gouged) trim parts are OK as cores. If you are in question as to...
Availability: Used / Wrecking Yard Item
Item #: 18691 -
Good used wheel lip moulding with no corrosion, obvious scratches or dents. This moulding will still have a good shine but do not expect NOS quality from a used piece of aluminum such as this one. When sending us a core in exchange please do not send twisted, ripped, corroded parts for an exchange. Dull, slightly dented, warped or scratched (not gouged) trim parts are OK as cores. If you are in question as to whether your core is worthy of restoration or not please send us a digital picture...
Availability: Used / Wrecking Yard Item
Item #: 18693 -
Good used wheel lip moulding with no corrosion, obvious scratches or dents. Will have some what rough texture down low on the leading edge from road debris. This moulding will still have a good shine but do not expect NOS quality from a used piece of aluminum such as this one. When sending us a core in exchange please do not send twisted, ripped, corroded parts for an exchange. Dull, slightly dented, warped or scratched (not gouged) trim parts are OK as cores. If you are in question as to...
Availability: Used / Wrecking Yard Item
Item #: 18689 -
Good used wheel lip moulding with no corrosion, obvious scratches or dents. This moulding will still have a good shine but do not expect NOS quality from a used piece of aluminum such as this one. When sending us a core in exchange please do not send twisted, ripped, corroded parts for an exchange. Dull, slightly dented, warped or scratched (not gouged) trim parts are OK as cores. If you are in question as to whether your core is worthy of restoration or not please send us a digital picture...
Availability: Used / Wrecking Yard Item
Item #: 20422 -
Good set of four used wheel lip mouldings for your 1969 - 1970 Mercury Cougar. What is considered to be an "acceptable core" is solely at our discretion. If you are in question as to what good cores are, please send quality, in focus, close-up digital pictures to westcoast@classic-cougar.com *NOTE* Some "on the edge" cores that need extra labor can be given a partial credit.*Note - This is a core exchange item only, trim will not ship until your acceptable moulding core is received by WCCC....
Availability: Out of Stock
Item #: 42374 -
Replaces Ford part number C9WY-16038-B.
Availability: Rare / NOS Part
Item #: 42375 -
Replaces Ford part number C9WY-16039-B.
Availability: Rare / NOS Part
Item #: 42382 -
Why is this right rear wheel lip so costly and difficult to find these days? Consider this... The right rear was the first to go obsolete from Ford. The right rear is the one most likely to get damaged because of it being the corner that is in the "blind spot". Remember, these early Cougars did not have RH mirrors! Lastly and maybe the most relevant is the fact that the right rear wheel is your traction tire which means more damage from flying road debris, loose tire chains and the like. It...
Availability: In-Stock Item
Item #: 31226 -
This retainer clamps together the two edges of the shroud and sets into the mounting holes on the column. The original is very hard to remove because of the saw blade teeth inside the grooves, and most times the tabs will easily break off. This reproduction will not have those teeth. Fits all factory 1970 Mercury Cougar and Ford Mustang, they use the same plastic collar around the column. If need be, simply widen the retainer for a better fit. *NOTE* For tilt column...
Availability: In-Stock Item
Item #: 30942 -
Set of four re-chromed vinyl top mouldings. The vast majority of hardtops in 1969 and 1970 had painted mouldings, but on two tone painted cars and the 1970 "Hounds-tooth" edition, chromed mouldings were supposed to be included. However, we have found exceptions to the rule. If you have extra sets of cores above and beyond the four needed to exchange, we would be willing to give in store credit. Restored moulding will not ship until we receive your cores. All mounting studs must be intact to be...
Availability: In-Stock Item
Item #: 33135 -
Set of four NOS vinyl top mouldings. The vast majority of hardtops in 1969 and 1970 had painted mouldings, but on two tone painted cars and the 1970 "Hounds-tooth" edition, chromed mouldings were supposed to be included. However, we have found exceptions to the rule.NOTE: These mouldings will have some shelf wear, see photos above. If you have extra sets of cores, we would be willing to give in store credit. Ford casting numbers on backs: Driver side C9WB-65423A19 Passenger side...
Availability: In-Stock Item
Item #: 19469 -
Complete kit with 12 white plastic mounting clips, 2 black plastic mounting brackets that attach rocker mouldings to scoops, 2 aluminum rocker mouldings and 2 chrome plated scoops.
Due to supplier shortage, the metal rocker panel clips are not available at this time. Click Here to View Installation Instructions These are correct for 1969 only but can be used on any year 1967-1973 ...
Availability: In-Stock Item
Item #: 41550 -
Sold as a set of twelve (two more than required), replaces Ford part #C9WY-6510182-A. From the factory there were five of these on each side for a total of ten per car. These same clips were also used on 1977-1979 Mercury Cougars and Thunderbirds. Most likely they were used on other FoMoCo products.Fits: 1969 Mercury Cougar1970 Mercury Cougar
Availability: Used / Wrecking Yard Item
Item #: 25149 -
Used driver side (left hand) lower rocker moulding / trim for the Mercury Cougar. There is a slight difference between the driver and passenger side mouldings and it is in the contour on the ends. These are not correct for the 1969 as the rear wheel opening was smaller in size and the 1970 had a factory screw hole at the rear. These 1970 mouldings are about 78-3/4" long. These almost always have one or two holes drilled in them are dull at the front due to road debris and have multiple small...
Availability: Used / Wrecking Yard Item
Item #: 24676 -
Correct plastic rocker moulding clips with Ford engineering # C9WB-6510182-A, Ford part #C9WY-6510182-A. There are five of these on each side for a total of ten per car. These same clips can be found on 1977-1979 Mercury Cougars and Thunderbirds. Most likely they were used on other FoMoCo products. If you know of other applications where these clips can be found let us know so we can post the information to help others in their search. Sold Individually.
Availability: Used / Wrecking Yard Item
Item #: 19455 -
Ford part number C9WY-6510198-A. This is the metal rocker moulding clip that attaches the front and rear of the mouldings to the car in 1969 (except the Sport Special which only has them on the rear). In 1970 a Phillips screw held the rear end of the rocker moulding to the quarter panel on each side so just the fronts of the mouldings used these clips in 1970. Keep in mind that this same basic clip can be found on 1977-1979 Mercury Cougars and Ford Thunderbirds that were equipped with optional...
Availability: In-Stock Item
Item #: 25139 -
We do what we have dubbed as "core matching". The better quality cores you send us, the better product you will get in exchange. If you would prefer your original cores be restored just mention it in a note when you send in payment with your restorable parts. It is also a good idea to scratch your initials on the back side. New hood trim attaching clips with nuts available here. Fits: 1970 Mercury Cougar ...
Availability: Used / Wrecking Yard Item
Item #: 18704 -
Good used condition with the kind of patina you would expect from a car with about 100k miles. Great for that well kept driver that is not quite ready for a restoration.New hood trim attaching clips with nuts available here. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. ...
Availability: Used / Wrecking Yard Item
Item #: 12799 -
This is a good used core piece of trim that is ready to be restored or bolted onto that less than perfect driver.
Availability: In-Stock Item
Item #: 25140 -
Correctly restored, anodized aluminum trim. Requires painting in the recessed areas. New hood trim attaching clips with nuts available here. Fits: 1970 Mercury Cougar
Availability: Used / Wrecking Yard Item
Item #: 18705 -
Nice used piece with no salt corrosion or serious damage. Ready to fasten to your driver!New hood trim attaching clips with nuts available here. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.
Availability: Used / Wrecking Yard Item
Item #: 12800 -
Good used core trim part that is ready for restoration.
Availability: In-Stock Item
Item #: 25136 -
These 1970 eyebrow mouldings have always been very sought after. Due to their exposed location they often times are mangled or missing. The better the core you provide, the better end product you will receive. If the core needs a lot of work the end result is they end up being thin which of course means they are more prone to future damage. If you have extra cores we would be happy to apply a credit towards your purchase. This purchase requires that you...
Availability: In-Stock Item
Item #: 10543 -
Reproduction clip for attaching the 1969 front fender extension moulding / trim and the 1970 hood moulding / trim found on the Mercury Cougar. The 1969 application calls for 2 of these clips along with 1 larger clip per side. If you need the larger clip for the 1969 front fender extension moulding / trim, you can get'em right here. The hood lip brightwork for the 1970 requires 4 per side. *NOTE* The threaded stud on this clip is a little longer than the original ones. This...
Availability: Used / Wrecking Yard Item
Item #: 53191 -
Used seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1 or Ford Service part number D1AZ-10B924-A
Availability: Used / Wrecking Yard Item
Item #: 23907 -
Low fuel option electrical relay. Stamped C6AF-10A968-A, Ford engineering number C5AZ-10A968-C. This relay was used on 1965-70 Ford and Mercury full sized cars, 1968-70 Torino/Cyclone/Montego/Fairlane, along with 1967-70 Mercury Cougar and Ford Mustang with that low fuel option. *Note - Generally this will not solve your low fuel indicator problems. The low fuel indicator failure is almost always due to a failed thermistor. The thermistor is located on the fuel sending unit in the fuel tank. ...
Availability: Used / Wrecking Yard Item
Item #: 10172 -
Used in 1969-70 Mercury Cougars for the stop lamps, located under the dash on a panel next to the fuse block.15amp circuit breaker. It is 1.07" x 0.40" and has a single green dot. Box is marked Tung Sol, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. Also fits 1969 and newer Mercury full size, 1970-71 CycloneFord part number C9MY-14526-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the...
Availability: Used / Wrecking Yard Item
Item #: 12928 -
Tested and working relay for the 'headlights - on' reminder. Relay with mounting tab for 1970 Standard model Mercury Cougars (XR7 models use a different relay/bracket) and 1970 Ford Mustang with convenience option. Additionally fits 1970 full size and mid sized Ford and Mercury cars with headlights on reminder option. This relay controls a buzzer as a reminder to turn off the headlights or remove the key, when the door is opened.Replaces Ford part number D0AB-10C838-A or D0AZ-10C838-A. ...
Availability: Used / Wrecking Yard Item
Item #: 12833 -
Tested and working relay for the 'headlights - on' reminder. Relay with mounting tab for 1970 XR7 model Mercury Cougar (Standard models use a different relay/bracket). This relay controls a buzzer as a reminder to turn off the headlights, or remove the key, when the door is opened.Replaces Ford part number D0WB-10C838-A or D0WY-10C838-A.
Availability: Used / Wrecking Yard Item
Item #: 13604 -
Used bracket for holding either the emergency flasher or turn signal flasher on many Fords dating from 1963. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This holder attaches to one of two different relay mounting brackets. Couple of different designs were also used. Additionally there is also a different style of flasher mounting bracket. See our related items.Replaces Ford part number C3AB-13351.
Availability: Used / Wrecking Yard Item
Item #: 15813 -
Used bracket for holding either the emergency flasher or turn signal flasher. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This holder attaches directly to the rear of the metal dash with a hex head machine screw.Replaces Ford part number C8AB-13351-A.