All Available Parts - 1968 Mercury Cougar

This deluxe wood-grain two spoke wheel was used on the majority of the Mercury Cougars built for 1968 and many other Ford, Lincoln and Mercury cars through 1969. The back portion of the wheel on the 1968 Cougar Decor level interior cars was color coded to the interior of the car. On the Standard models for 68, the first part of the year would have used a wood grained deluxe wheel and the later part of the year was a solid colored wheel. The benefit of going reproduction on this wheel as...

This deluxe wood-grain two spoke wheel was used on the majority of the Mercury Cougars built for 1968 and many other Ford, Lincoln and Mercury cars through 1969. The back portion of the wheel on the 1968 Cougar Decor level interior cars was color coded to the interior of the car. On the Standard models for 68, the first part of the year would have used a wood grained deluxe wheel and the later part of the year was a solid colored wheel. The benefit of going reproduction on this wheel as...

This deluxe wood-grain two spoke wheel was used on the majority of the Mercury Cougars built for 1968 and many other Ford, Lincoln and Mercury cars through 1969. The back portion of the wheel on the 1968 Cougar Decor level interior cars was color coded to the interior of the car. On the Standard models for 68, the first part of the year would have used a wood grained deluxe wheel and the later part of the year was a solid colored wheel. The benefit of going reproduction on this wheel as...

Reproduction Two Spoke Steering Wheel Pad for the 1968 Mercury Cougar Check out our video review

Grade C will have terrible paint and dings which can be pushed out from the backside with your thumbs. This will require our repro burl applique. Here's a little inspiration for you to get our Burl Wood kit and wrap your own parts! ...

Pit free original rear console courtesy light for all consoles 67-68, does not usually come with a good lens as most are cracked, faded or missing. Casting number as seen on the back reads C7ZB-13743-A. Number imprinted on wire can be: C4VB-13757-A.

Optional trunk lamp. Includes mercury switch that mounts on inside trunk lip, round plastic wire protector bezel, mounting screw and wiring pigtail. Ready to install working part, #631 bulbs available. Guaranteed to work, no cuts or splices.Can be added to any 1967 - 1968 Cougar and may be able to be added to the 67 - 68 Mustangs, but some Mustang forums indicate the Mustang lamp had a different wire length than the Cougar lamp and this version is stamped with the correct part number for the...

Differs from the original lens in that it is all white. The original was painted white on one half and left clear on the other.

Used rear driver side (left hand and passenger side (right hand) courtesy / opera light housings for the Mercury Cougar. The rear courtesy / opera light was standard on all XR7 Cougars, but were a popular option on decor and standard level interior Cougars. These units are marked LH for the driver side and RH for the passenger side. Also sold individually, see related items. Ford part # C7WB-13B729-C or C7WY13A744-C for the passenger side, C7WB-13B736-C or C7WY-13A744-D for the driver side....

Used grade "A" rear courtesy / opera light lens for the Mercury Cougar. The opera lights came as standard equipment on all XR7 Cougars, but were a popular option on decor and standard level interior Cats as well. These used lights are they very best we can provide, but will not be 100% mint. Check out our reproductions, they are VERY nice. This unit is sold individually. Ford part # C6VB-13B726-A.  *TRIVIA* Did you know that these units were originally used on the 1966 Lincoln? The...

C7WB-13K705-C-AGRADE Left side courtesy lamp assembly attached to the door panel of all 1967 Cougars and 1968 Cougars with either decor or XR7 interiors. Courtesy light assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 16, C7WB-13K705-C courtesy lamp assembly left hand side. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. Hardest side to find in primo condition most get dinged up from errant seatbelts. This...

Left side courtesy lamp assembly attached to the door panel of all 1967 Cougars and 1968 Cougars with either decor or XR7 interiors. Courtesy light assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 16, C7WB-13K705-C courtesy lamp assembly left hand side. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses.Replaces Ford part number C7WB-13K705-C.Fits:1967 Mercury Cougar1968 Mercury Cougar ...

C7WB-13707-C Right side courtesy lamp assembly attached to the door panel of all 1967 Cougars and 1968 Cougars with either decor or XR7 interiors. Courtesy light assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 16, C7WB-13707-C courtesy lamp assembly right hand side. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway.

Right side courtesy lamp assembly attached to the door panel of all 1967 Cougars and 1968 Cougars with either decor or XR7 interiors. Courtesy light assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 16, C7WB-13707-C courtesy lamp assembly right hand side. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses.Replaces Ford part number C7WB-13707-C.Fits:1967 Mercury Cougar1968 Mercury Cougar ...

Map light bezel for overhead roof consoles on both 1967-68 Mercury Cougar XR7 and Ford Mustang. These are a great reproduction at a great price. These were always pitted and before the reproductions came out three years ago a very nice used pair sold for about $100. To date we have sold more than 300 pairs and have had great feedback! Sold in pairs. Bezels only. Sometimes called a 'door' Ford part number C7ZZ-13788-A. *Customer Comments* Hello. I just bought my first 1967 Cougar XR7 in about...

Reproduction rear courtesy / opera light lenses for the Mercury Cougar. The rear courtesy / opera lights were standard equipment on all XR7 Cougars, but were a popular option many other standard and decor level interior Cougars. If your car did not originally come equipped with them, it is actually quite easy to install them, but you will need to purchase our used housing /socket assemblies. These are fantastic quality and a perfect fit. Sold as a pair only. Ford part # C6VB-13B726-A. *TRIVIA*...

Good used shift indicator light and pigtail for the 1968 with automatic and without console. Comes as shown with the clip on diffuser for automatic shifter lever. The only difference between this shift indicator light without console and with console is the diffuser. The diffusers pull off and interchange. This light harness is also known as the PRNDL light harness (park, reverse, neutral, ...) The 1968 wiring harness has a blue double male plug. Fits 68 CougarFits 68 Mustang Check out our...

Rechromed Bezel for your door courtesy lights found on all 67-68 Cougars except the 1968 Standard model. These will require some patience with a dremel tool to remove the lenses from your cores and place them in these. Passenger and driver are the same, keep in mind the red lens goes to the back of the bezel. To be eligible for core refund, your cores can only show light pitting. ...

Used rear driver side (left hand) courtesy / opera light housings for the Mercury Cougar. The rear courtesy / opera light was standard on all XR7 Cougars, but were a popular option on decor and standard level interior Cougars. These units are marked LH for the driver side and RH for the passenger side and are sold individually. Also sold as a PAIR. Ford part # C7WB-13B729-C or C7WY13A744-C for the passenger side, C7WB-13B736-C or C7WY-13A744-D for the driver side. *TRIVIA* Did you know that...

Used rear passenger side (right hand) courtesy / opera light housings for the Mercury Cougar. The rear courtesy / opera light was standard on all XR7 Cougars, but were a popular option on decor and standard level interior Cougars. These units are marked LH for the driver side and RH for the passenger side and are sold individually. Also sold as a PAIR. Ford part # C7WB-13B729-C or C7WY13A744-C for the passenger side, C7WB-13B736-C or C7WY-13A744-D for the driver side. *TRIVIA* Did you know...

Reprint of an original pamphlet that was intended to help Ford techs date and identify by using the codes found on the parts. Covers all LFM models, 23 pages.

Have you been in a discussion with someone about how many W-code GTEs were made? The real percentage of Cardinal Red convertibles that were made? How many Eliminators were made each year? Now you'll know these things and so much more. This book contain never before published information drawn direct from company records, and over 14,000 statistics. This book includes: Exhaustive charts of paint color-trim combinations Engine-transmission production for each body style Option production rates...

This 165 page book has been in the works for over a decade now at Marti Auto Works and it is a must have for anyone purchasing, restoring or researching a 1967-1973 Mercury Cougar, Ford Mustang or Shelby. Even if you are a Mopar or Chevrolet guy, if happen to frequent swap meets and salvage yards you need this invaluable little book tucked away in your tool box or car as you maybe walking right past VERY valuable cars and parts and not even know it... In Kevin's words, "Have you been...

Grade B will have failing mylar chrome trim. Please list in the comments section of your online order what color you prefer and we will attempt to get you the desired color, limited to stock on hand.

Grade B will have failing mylar chrome trim. Please list in the comments section of your online order what color you prefer and we will attempt to get you the desired color, limited to stock on hand.

All of our Standard and Decor, 1967 and 1968 rear interior panels come naked without the horizontal basket weave strip. We often will leave a yellowed, peeling one in place when they ship but if they are in good shape we remove them and sell them separately. If you purchase a panel from us and want a grade C strip, just mention it in the comments section of your online order and we will include it for free. Used passenger side (right hand) rear interior panel in blue for the standard Mercury...

All of our Standard and Decor, 1967 and 1968 rear interior panels come naked without the horizontal basket weave strip. We often will leave a yellowed, peeling one in place when they ship but if they are in good shape we remove them and sell them separately. If you purchase a panel from us and want a grade C strip, just mention it in the comments section of your online order and we will include it for free. Used driver side (left hand) rear interior panel in blue for the standard Mercury...

This is a restored 1968 steering wheel that is correct for all but the later production, standard interior equipped 1968 Cougars. Only the XR7 & XR7G received the woodgrain center section, the decor and standard interior equipped Cougars received a color coded to the wheel vinyl insert. All 1968 Cougars used this center emblem except the XR7G which used a larger metal version. This wheel does not include the center pad assembly or horn ring (shown for display purposes only). As we prefer to...

Good used wheel with no cracks but will show wear on the woodgrained fascia. We usually have several wheels for $20-$100 more and $20-$100 less than the wheel pictured here. Most are black in color but we do have a few colored wheels. Call for the many details and options. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Cracked wheel good for restoration. Usually cracked at 12 and 6 as well as on the two spokes.Having issues with wobbly or loose steering? Check out our video on sloppy steering below.

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Having issues with wobbly or loose steering? Check out our...

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Note that the color on these has too much gray in it and is...

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad.

Correct for standard and decor level interiors. No guarantee you will get your color of choice. Comes as shown with bezel, emblem and vinyl surround. Engineering number as seen on back of bezel reads C8AA-3D754-A

Used on all Cougar steering wheels except XR7 which had a wood-grain center. We have most colors in stock but they usually need to be repainted. No guarantee you will get the color of your choice.

Average condition with no obvious blems, but will show substantial fading. A perfect replacement for our woodgrain Burl wraps if yours is caved in or corroded and nasty looking. Here's a little inspiration for you to get our Burl Wood kit and wrap your own parts!

Incorrect chrome finish (supposed to be satin not chrome) Mustang part that requires modification to make the metal XR7 insert fit. This is the only new alternative to your broken bezel, we sometimes get in an original that just needs paint. This unit will also fit the Cyclone, Montego, and many other Mercurys and Fords. Replaces Ford part # C8ZZ-3D572-A.

This is the correct horn panel bezel for all 1968 standard model Cougar steering wheels. The satin paint will need to be resprayed but the two mounting studs are in place and there are no cracks or burns. Please see related for XR7 model bezel. Ford part number C8AA-3D754-A.

Reproduction Two Spoke Steering Wheel Horn Ring for the 1968 and 1969 Mercury Cougar. This is a very good reproduction piece. The original horn contact pieces fit nicely. This casting, while different than the 1968 version with the empty cavities is actually stronger. *NOTE* Save your old horn ring, you will need to transfer the rubber spacer and the horn contacts to this reproduction part.*CUSTOMER REVIEW* Called WCCC the other day after calling around to a lot of garages and auto parts...

These pamphlets were found buried in the back room of a San Jose California Lincoln-Mercury dealership. There was no reason to keep them after the warranty expired so most were discarded long ago. Great for that person who likes original documents. Limited quantity.

Manual on how to modify your FE big block Ford for street or strip.

Reproduction BOSS 302 Chassis Modification for the Strip Track Manual. This little book is packed full of tips and tricks to make your Cat or Pony and handling MACHINE! The tips in the manual also apply to the 1967-68 Cougar or Mustang. Time to sharpen the claws on your flexxy feline!

This promo guide features all Mercury's from 1968. Notice the Model A in the background. It features a great shot of a red GTE blazing down the track.   ...

Lots of great photos inside and out of the Cyclone, Montego and 1968 Cougar.

Reproduction idle mixture screw caps for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All white plastic caps. These were the tamper proof type of caps as installed from the factory.

Set of 3 screws for installing the center air conditioning vent on 1967-68 Mercury Cougar XR7 models. Center vent mounts to the back side of the dash bezel with the 3 supplied screws. Check for cracks in the mounting holes in the dash plastic. Do not overtighten, make them 'just' snug. These will work with original or reproduction XR7 A/C center vents.  

#8 tapping screw for attaching the map pocket to the door panels on any 1967-68 Mercury Cougar XR7. Sold individually, set of 4 needed per car, 2 per side. Chromed, Phillips pan head screw. AMK B-13283.

5/32 Allen wrench. We offer this Allen wrench to go along with our dash bezel removal tools. This handy dandy 5/32 Allen wrench is needed to attach the ignition bezel tool to any of the 1967-69 Mercury Cougar or Ford Mustang ignition switch bezels.

AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to top loader transmission on all 1967-69 Mercury Cougar and Ford Mustang with 390 or 428CJ engines. AMK number F-1741.

AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to top loader transmission on all 1967-69 Mercury Cougar and Ford Mustang with 289, 302, 351W, and 351c engines. AMK number F-1414.

AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to any automatic transmission on all 1967-69 Mercury Cougar and Ford Mustang with 289, 302, 351W, 351C, 390, 428CJ engines. AMK number F-176.

AMK fastener kit for attaching manual transmission clutch Z-bar brackets. 1967-68 Mercury Cougar and Ford Mustang with 289 or 302 engines. AMK number F-867.

AMK fastener kit for attaching manual transmission clutch Z-bar brackets. 1967-68 Mercury Cougar and Ford Mustang with 390 or 428CJ engines. AMK number F-866.

Gasket, for the C6 transmission filter. Fits all c-6 transmissions 1967-73 Mercury Cougar and Ford and Mustang.

This 1967-68 Mercury Cougar and Ford Mustang shield, was installed at the factory to protect the heater motor from being damaged when the Big Block 390-427-428's were being dropped in. As noted in the factory assembly manuals we sell, they were supposed to be removed once the motor was in place. We have found that more often than not they were left in place as it was probably too time consuming to remove them. Technically they should not be in place on a concours car but practically...

Concourse correct 3" long nipple that installs in the water pump, with the correct plating.C8OZ-18599-A.

Top screw on the wing or vent window frame on any 1967-68 Mercury Cougar or Ford Mustang. Screw attaches the door glass run insert to the chromed vent frame at the top. Screw accessible when door is open top leading edge of wing window frame. *Item of Note - screw is slightly too long. The tip could scratch the front edge of the door glass or chrome trim on top of the door window. We suggest grinding down the tip about 1/8 inch, prior to installation. We have looked and this is the only...

This is from the Ford accessory catalog starting in 1968. This is a rear seat ash tray for cars without center console. Textured plastic construction with typical ash tray and receptacle as found on the rear of the console. FoMoCo boxed with Ford part number C8WY-6504803-A. The textured plastic box has a casting number of C8WA-6566836-A. Will fit 1967 Mercury Cougars too. Included are original instructions for installation. 

These new navy blue shirts feature a distressed white graphic with the slogan, "It's Like A Mustang, Only Better!" and "Cougar: Since 1967", wrapped around the image of a first-generation Cougar. This design is a WCCC original, and we think it sums up most Cougar owners' true feelings about their cars. Shirts are Port & Company, 4.5-ounce, 100% ring spun cotton, with removable tags. These are softer and more comfortable than some of the previous shirts we've used. Pre-shrunk, but cold wash is...

New from WCCC! This black T-shirt features subdued grey graphics on front and back, with a small WCCC logo on the front left chest, and a rear view of a 1967-68 Cougar on the back with the taillights lit up in red. We think this is a great looking shirt that all classic Cougar fans will enjoy. Shirts are Port & Company, 4.5-ounce, 100% ring spun cotton, with removable tags. These are softer and more comfortable than some of the previous shirts we've used. Pre-shrunk, but cold wash is...

The Big Book is here! This cache of cool Mercury Cougar knowledge features 186 entertaining and informative pages that focus on the 1967-73 Cougar. Don Skinner, former editor at the Cascade Cougar Club, spent 8 years mining valuable data throughout the Cougar community and compiling all of his little gems into "The Big Book." This jewel is chock-full of great tech information, pictures, fun facts, production numbers, rare concept cars and much, much more. Many of the photos and documents...

In 1967 Ford was missing the street performance boat in a big way. Almost 700,000 high performance cars were sold and Ford, the Total Performance company, was getting about 7% of that market. Loyal owners were unhappy, dealers were unhappy, and Hot Rod magazine called Ford performance cars "counterfeit".Bob Tasca was the youngest Ford dealer principal in America. He was operating in the smallest state on the union, New Hampshire. His first showroom was leveled by a hurricane barely months...

As you know there are two versions of the Mercury Cougar: Standard and XR-7. In this issue, we take a look at three standard Cougers. First we look at the 1968 Standard hardtop owned by John Stravrou.Next we admire the 1970 sunroof Standard owned by Jeff and Carol Bingaman.And last but not least, we lay eyes on the award-winning 1973 Standard convertible owned by Dwain Barker.A great follow up to the first two issues found here: Issue #1, Issue #2 ...

This is one of the best small block Ford V-8 books on the market. It covers 260-289-302 V8 engines. Carburetor numbers, distributor numbers, covers all engine brackets, pulleys, and parts of Ford small block engines. 100's of pages with pictures, casting numbers, and explanations by year. A must for concours detailing and year by year correctness. Author Bob Mannel, covers small block V8 engines and components 1962-69. References all Ford cars that these engines came in. Mustang, Cougar,...

The latest addition to our Legendary Cougar Magazine collection. Issue #4 is an International Issue, featuring Cougars from Australia, Germany, Ireland, Norway and Sweden.In This Issue:FeaturesLuck of the Irish – Dave Rooney talks about what it's like to own the only 1967 Cougar on the Emerald Isle. LCM's Creative Consultant Brian Veit transforms Dave's photographs taken in front of his house to make it appear that they were shot in-period in a photo studio.Cougars Down Under – Owning an early...

In Issue 5, the editors have added a new department called “Cougar Marketplace,” which will follow recent sales of classic Cougars. This month, we look at the recent auctions held in Arizona and Florida. As we near the end of Volume 1, we’re looking forward to Volume 2. In Cat Tracks, co-editors Bill Basore and Rich Truesdell review the past year and look at what the future may hold for Legendary Cougar Magazine.You will also find two very useful tech articles detailing volt meter installation...

We have an impressively eclectic group of Cougars in this month’s issue, ranging from all-out performance in the 427-equipped GT-E, to a 1969 Sports Special, the only Cougar that legitimately could be called a Shelby. It’s Shelby Cloth interior makes it one of the most rare and unusual Cougars every built.The pristine 1973 XR-7 convertible we feature is the closest to a brand-new Cougar we’ve ever seen, with only 471 original miles on the clock. At the time it was built, it was believed it...

In This IssueFeaturesWatch for the Presidential Limo In 2016 – The Cougar will turn 50 in the Fall of 2016, and new CCOA President Gavin Schlesinger is already planning the celebration, all the while behind the wheel of his daily driver 1968 XR7-G.Long Way From Home – This Cougar traveled 12,000 miles from its birthplace in Dearborn, Michigan to its first home in Exmouth, on Australia’s West Coast. It has lived all 48 years Down Under. LCM editor Rich Truesdell talks with owner Mike Merema and...

In This IssueFeaturesFamily Affair – Suds Reddy, a life-long Blue Ovaler, has the best of all worlds, a supportive family including a daughter with gasoline in her blood stream, and what is quite possibly the best documented, most original first-generation classic Cougar Rich Truesdell has ever seen.Calgary Cougar – Tim Prieur, a Ford guy going back to his childhood in Calgary, Alberta, has not one but two Cobra Jet convertibles, a 1971 Mustang and this month’s Second Generation feature car, a...

[No Description Provided]

[No Description Provided]

[No Description Provided]

[No Description Provided]

Here's a new book about the king of classic Cougars, the GT-E! This book starts out with the standard '68 Cougar and XR-7 as both models were available with the GT-E option. The reader is then taken through the early stages with the XR-7S and prototypes. Following these pages is the GT-E as we all know it, and then a brief venture into 1969. Lastly are parts lists for the 427 GT-E and the 428 GT-E. This book was written for the casual reader as well as the GT-E enthusiast.The book contains...

Here's a new book about the luxury king of classic Cougars, the XR7 G! The book contains many pictures and documents never published before. A great addition to your collection!From the author of The BIG BOOK of Cougar, Don Skinner.

Get your hands on the new, long awaited Mercury Cougar Eliminator book! Besides various specifics about "optional this" and "factory that", this book includes stories written by car owners. These stories remind us that our cars are more than just a collection of technical details. They link the cars directly to the people who own(ed) them. Why did they choose a Cougar and what impact did it have on their lives? Where did it come from and where is it now? Truly, the stories and history are the...

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Quality wiring reproduction for Perfect Circle brand of speed controls as found on most 1967-1971 Ford - Mercury - Lincoln automobiles. Main harness with Ford part number 9A840, can be used on a variety of model and years. Harness connects the servo, has grommet for firewall, and connectors under the dash. Jumper wire to the brake pedal.

This polyurethane steering coupler repair kit for your tilt column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. Some customers feel polyurethane improves steering feel. Replaces factory steering coupler on 1967 - 1973 cars. Most 1967 Mustangs with fixed steering columns do not have coupler.Replaces Ford Part #: C7OZ-3A525 Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Fixed steering column from a 1968 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often breake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. Upper and lower mounting brackets, and wire keeper (wiring cover...

Reproduction tilt / tilt away steering column wiring harness for the Mercury Cougar or Ford Mustang. Exact copy in every way! If you call and tell us the long sad story of how when you pulled your column in 1982 in a bone yard and left this harness behind unknowingly. we will have to charge you extra... Just kidding! *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Reproduction clevis for the tilt/tilt away steering column equipped Mercury Cougar or Ford Mustangs. This unit attaches the pawl cable to the vacuum motor shaft. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used rubber washer for the locking pawl cable to cable guide used for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This unit fits against the cable side of the ninety degree angle. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts...

Emergency flasher bezel for the side of the tilt steering column. Reproduction bezel in black. Replaces most all tilt swing steering columns from 1967-69. Replaces Ford part number C9AZ-15C80-A, and an earlier part number starting that was likely C7SZ-15C580-A.

Used vacuum actuator for the tilt / tilt away steering column in the Mercury Cougar, Ford Mustang or Thunderbird. This unit was used through late 1968 and 1969 and has the embedded safety starter switch in good working order. 1967 through early 1968 actuators are white, where these units are black in color. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at...

American Cushion Industries' cushions are reinforced with tough polypropylene mesh backing material for stability and long life. All of their products, including highback cushions are molded with their exclusive cold cure process.This seat cushion foam is of a much softer lighter material than the other seat cushion foam that we offer. Much more comfortable and plush and about half the weight. Click on images to enlarge. ...

Sold as one-seat set including one bottom cushion and one backrest cushion.

Relay for 1968-69 Mercury Cougar or Ford Mustang with factory speed control. This is the brake release relay. Mounts to the Regulator mounting bracket. Ford part numbers C8ZA-9D737-A and C8ZZ-9D737-A.

NOS Speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln.  The 1968 Electrical manual shows a Lincoln part number of C7VA-9D752-G. Service replacement part number is D1VY-13305A. Would need to remove the white tilt bale collar prior to use.

Grade B speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G

This latest of a series of 67 - 68 reproduction sheet metal parts is just what the market has been waiting for! The dimensions are EXACT down to the 1/16", black primer finish is very similar to what the later service replacement parts were from Ford. The hood weighs almost seven pounds more than original due to the material being made from a slightly thicker material than OEM. The hood hinges are mounted by welded in nuts instead of the J nuts like the originals. This is both good and bad in...

This latest of a series of 67 - 68 reproduction sheet metal parts is just what the market has been waiting for! This listing is for the framework of the hood. This frame is for someone who needs to replace the rotted out bits of your hood frame, or for someone who simply wants a base to make a fiberglass hood on their own.  These hood frames are oversized and cannot ship through UPS or USPS, so it will need to ship via truck freight. You can expect to pay somewhere between $200-300...

This listing is for the person who only has rust under the lip at the front and does not want to pay shipping on an entire frame that must ship via truck freight. It will come as shown unless you contact us. The part will be the same price no matter where we cut it, let us know in the comments section where you would like us to cut if you want something other than what is shown. ...

This listing is for the person who only has rust under the corners at the rear and does not want to pay shipping on an entire frame that must ship via truck freight. It will come as shown unless you contact us. We can also cut the section in half if you only need one corner.  The part will be the same price no matter where we cut it, let us know in the comments section where you would like us to cut if you want something other than what is shown. ...

New from WCCC! This black T-shirt features subdued grey graphics on front and back, with a small WCCC logo on the front left chest, and a rear view of a 1967-68 Cougar on the back with the taillights lit up in red. We think this is a great looking shirt that all classic Cougar fans will enjoy. Shirts are Port & Company, 4.5-ounce, 100% ring spun cotton, with removable tags. These are softer and more comfortable than some of the previous shirts we've used. Pre-shrunk, but cold wash is...

New from WCCC! This black T-shirt features subdued grey graphics on front and back, with a small WCCC logo on the front left chest, and a rear view of a 1967-68 Cougar on the back with the taillights lit up in red. We think this is a great looking shirt that all classic Cougar fans will enjoy. Shirts are Port & Company, 4.5-ounce, 100% ring spun cotton, with removable tags. These are softer and more comfortable than some of the previous shirts we've used. Pre-shrunk, but cold wash is...

This is a stock photo, the actual lever we have will most likely be worn and will not be as nice as the one pictured. Grade A speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we may price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G This icon means that we're looking to buy...

Features 274 pages / 750 photos/ 12,300 items / history / finishes / measuring and more. This book provides detailed information about the fasteners specified in assembly manuals and parts books. All 12,300 fasteners are referenced to a photo! Must have for anyone wanting to correctly put together a 1955-1973 FoMoCo product.

The 1967 Cougar was Mercury's attempt to enter the Pony Car market segment popularized by the April 1964 introduction of Ford's Mustang. Introduced in the fall of 1966 for the 1967 model year, the first-year 1967 Cougar exceeded all sales expectations with 150,893 units sold. It was selected as Motor Trend's 1967 Car of the Year. Legendary Cougar Magazine is dedicated to the first three generations of Mercury's luxury Pony Car. Each bi-monthly issue includes features on the first-generation...