All Available Parts - 1968 Mercury Cougar

For any year 1967 1968 1969 1970 Mercury Cougar with an FE 390, 427, or 428CJ engine. Identified by the round dimple stamped into it. Compare the OEM used part price to the reproduction part. For restoration purposes, this bracket was factory painted satin black.

1968 XR7 and standard Cougars use the same rear wiring harness to the taillights. This is a grade "A" premium grade harness that is not sun damaged, spliced, or damaged in anyway. XR7 and Standard Cougars use the same rear wiring harness to the taillights, only the sub-harness that connects to it that runs along the underside of the package tray and down to the fuel sending unit differs XR7 vs. Standard. The major difference is that the xr7 utilizes a two wire plug and the Standard Cougar uses...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. OEM style door jamb switch to release tilt/tilt-away columns on a 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the steering...

Electronic voltage regulator for use on any 1967-73 Mercury Cougar or Ford Mustang or Ford. Same foot print as originals, cover can be swapped.

Features the proper cover and original logos. I A S F stamped on cover.Replaces Ford Part #: C8TF-10316-A.* - Also came on some 70-71 A/C CarsThese new voltage regulators are improved and more reliable than the units we've sold previously.

Used pair of right and left engine block plates for any 1967-69 Mercury Cougar or Ford Mustang with 390 engines, or 1968-70 428 cobra jet engines. These can be made to work on a GT-E 427 if the passenger side mount is modified for clearance.Replaces Ford part number C7ZZ-6046-A  and C7ZZ-6046-B.

This Big Block motor mount bolts to the driver side (left hand) of the engine block. This original plate with the "L 427" stamped into the bracket. Fits 1968 Mercury Cougar GT-E with 'W' code 427 side oiler engine. A regular FE Cougar driver side will work with modification.  Ford part # C8ZZ-6046-C for the left hand bracket

Used grade "A" under dash wire harness is inspected, tested, and ready to install. These grade "A" harnesses will be rare uncut and unburnt beauty. This unit is for those of you who demand excellent original parts for your Cougar.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy original under dash harnesses. We are interested in all under dash harnesses, but are primarily interested in the XR7 harness. ...

Good clean used grade "A" under dash wire harness that was inspected, tested, and ready to install. This grade "A" harness will either be uncut or professionally repaired. Our wiring here in the Northwest tends to be among the best anywhere as we do not have high humidity to corrode connections and we do not have severe heat which tends to make wiring brittle in time.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep...

Used standard grade "B" under hood main wiring harness that is located in the engine compartment. This harness has plugs for head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All grade "B" electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where the grade "A" harnesses will be rare uncut beauties. 1968 Mercury Cougar Standard models only with AMP warning light. Not...

Used grade "B" XR7 main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where grade "A" harnesses will be rare uncut beauties. 1968 Mercury Cougar XR7 models with Ammeter only. Not compatible with Standard model Cougar with...

Used standard grade "A" under hood main wiring harness that is located in the engine compartment. This harness has plugs for head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All grade "A" harnesses will be rare uncut beauties. 1968 Mercury Cougar Standard models only with AMP warning light. Not compatible with XR7 model Cougar with Ammeter. Ford part # C8WY-14290-A.

Reproduction Dash to Engine Gauge Feed Harness with the push-on post oil sender for the 1967 and 1968 Mercury Cougar or Mustang with the 390, 427 or 428 Big Block. Replaces Ford Part #: C7ZZ-14289-ACheck out the video below on our new gauge tester: ...

Reproduction console feed harness for the 67 - 68 Cougar or Mustang. This OEM direct fit wiring harness supplies power from the under dash harness to the console harness.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

These original FoMoCo headlight switches have been tested for both vacuum and electrical functionality. These old switches also come with the already attached "C" shaped spacer that mates to the dash. We all know how hard it is to get that spacer glued in on a new switch (which doesn't come with the spacer). Stamped witht the "Motorcraft" trademark and Ford part number C8WB-11652-C. 

NOS, never been installed part they may or may not come with original box, will show shelf wear. Ford Engineering number stamped on the part is C8WB-11652-C.

These are all new, not rebuilt, OEM Ford quality. We recommend these over the generic version and the "concours" version. Marked with Ford D2AF-11450-AA part number, but is functionally correct for all 1967-73 Cougars. Black case as original.Replaces Ford Part #: C7AF-11450-A1 , B6AZ-11450-A , C7AZ-11450-A , D2AF-11450-A , etc

These amber colored bulbs are getting very hard to come by these days. Even the lesser quality painted amber bulbs have not been available from auto parts stores for over a decade now. If you search around you will see that some vendors retail these at over $5.00 each plus shipping! We have a limited supply of these bulbs, so you may want to get an extra pair. The 1968 Ford manuals call for a 97n bulb, but that is an error believe it or not. Sold individually and two are required per...

We have had so many dealers inquiring about these we are now offering dealers, and those who own multiple cars that use these rare bulbs, a quantity discount. We have witnessed these bulbs sell for as much as $9 each on ebay! The 1968 Ford Manuals call for a 97N bulb, but that is an error believe it or not. 

Good reproduction of a knob that is always broken off. Made from milled aluminum rather than plastic as the originals were made. This makes it so it is not as susceptible to breaking off. Unique to Cougars with tilt columns in 1968 - 1969. Replaces Ford part number C8MY-17513-C. This part also fits the 68-69 Mustang, Lincoln, Marquis, Thunderbird and other like models with an adjustable steering column.

1967 - 1968 Mercury Cougar emergency light flasher relay. Good used, original, and 'tested' unit ready to plug in and use. Lead wire not included, shown in picture for help in identification purposes. Replaces Ford part number C7WB-10C838-B. The reason we gave this used item a crappy logo, is that they weren't designed to last over 50 years. The simple electronics they used back when they made these cars just weren't up to par with the quality of electronics designed today. We recommend...

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with a manual transmission and drum brakes. This unique pedal that works with the wider collapsible 1968 steering column and with a clutch pedal. Shorter arm than power brake pedals. The picture may show hardware and pedal pad with trim, but the pedal is shipped bare.Ford part # C8ZZ-2455-E.

Steel tubing features tin/lead coating and plated zinc chromate fitting and are exact copies of the originals with color coded fittings. New copy of the 1968-69 Mercury Cougar and Ford Mustang manual drum brake master cylinder lines. 

Reproduction wheel cylinder link pin. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Sold individually. Ford part number B7A-2042-A.

Reproduction 4002 incandescent (non-halogen) low beam light bulb for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar. Plugs right in to the factory 3-prong plug and mounts in the outboard position on the car.These are close to OEM wattage (37.5 / 60 watt, OEM was 37.5 / 50 watt) to work with the factory headlight switch, without adding any relays like you would for higher wattage halogen bulbs.Ford Bulb #: 4002, Aftermarket Bulb #: 4000. Sold individually, 2 required per car. ...

Reproduction set of wheel cylinder link pins. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place.Sold as a set of four.

Reproduction passenger side (right hand) front wheel cylinder for 10 inch x 2-1/2 inch drum brakes. This unit fits in a 1-3/32 inch hole on the brake backing plate. Replaces Ford Part # C6OZ-2061-B or C9TZ-2061-B.

Original used speaker lead wiring harness pigtail for all 67 - 68 Cougars and Mustangs with factory AM radios. This wire pigtail is located in the kick panel.*Note - The only difference between this pigtail and the one listed for the 1969-70 dash speaker is the actual plug design.

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your driver side speaker, which is denoted by the orange wire. Red or black colored plugs are acceptable for the left hand speaker.Part of the stereo speaker wiring harness that goes to a pair of factory...

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio. Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your passenger side speaker, which is denoted by the white wire.Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the...

Original used stereo radio speaker wiring harness pigtail for all 1967-70 Mercury Cougars and Ford Mustangs  with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your under dash radio speaker wiring harness. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail.White speaker wire goes to the passenger side speaker, and the orange colored wire goes to the driver side speaker. This is...

Reproduction bracket for mounting the rear axle flexible brake hose. From the factory, these brackets were welded in. Double check your placement for your particular year, when welding the bracket to your car. Has correct "D" shaped hole for indexing the flexible brake hose to rear axle. Replaces Ford part number C7ZZ-2A051-A.

Want a little more from your hidden speaker system? This is it! The UNDERCOVERII was developed with an 8" woofer and 2 Piezo tweeters in each box. This system can be mounted in many of the same locations as the regular UNDERCOVER. With the 8" woofer in UNDERCOVER II, you get a much fuller, deeper, and richer sound. These fit well under the front seats of 1967-1973 Mustangs and Cougars and have a 200 watt capacity. Measurements are 11"W x 12.5"D x 3"H, sold as a pair. ...

Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.

Used radio bezel Grade A used. For use on 1967-68 Mercury Cougar or Ford Mustang cars without console. 2-3 different castings, need to be side by side to see minor difference. Ford part # C8ZA-18842 and C7ZA-18842.

Grade B 68 Radio Bezel for 1968 Mustang or standard Cougar. Holes often are modified for after market radio, might have broken upper mounting ear, pitting. Email for picture or detailed explanation of current stock on hand. Ford casting number C8ZB-6504567-CNeed some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a storage compartment. The slide up doors are different between the 2 years due to the handle being different. The...

Fragile black plastic channel selection button that often gets broken. Requires advanced skills to remove and replace.

This was used only on the 1968 Mustang and standard Cougar, not for XR7. If you would like one that has been modified for an after market radio or you would not mind other minor blemishes (Or a broken ear) we have several that would save you money.Ford casting number C8ZB-6504567-C This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or...

Factory radio delete or block-off plate from a 1967-68 Mercury Cougar or Ford Mustang. Seldom seen part, roughly 5% of all 1967-68 Mercury Cougars were ordered without any type of radio from the factory. Similar story with the Ford Mustang, most owners added some sort of radio or stereo soon after delivery. The factory radio bezels were made from chromed pot metal, these radio delete plates are made from plastic and vacuum chrome plated. This used example pictured, has most of the plating...

1968 Mercury Cougar AM-8 track Motorola manufactured radio. These will work and all wiring plugs will be present. Good working and tested radio, fresh installed 8 track belt, may have minor cosmetic issues from a past life. NOTE* The one radio we have in stock at the moment has working AM, all buttons work, but the 8 track tape will not stay in position and needs fiddling - Call for advice. *NOTE* Does not include brackets or knobs. Ford master part # C7WA-18806-A, Chassis and Escutcheon...

Used non-functioning AM-8 track Motorola manufactured radio. These will not work and may have minor cosmetic issues from a past life. Ford part # C7WA-18806-A, Chassis and Escutcheon Assembly. Stamped T8MZ. *NOTE* Does not include brackets or knobs. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

F8TBZ Mercury Cougar and Ford Mustang AM/FM stereo radio. Grade "A" condition guaranteed to work well. When you adjust for inflation these radios are actually less expensive now than in the day! 1968 was the first year for a AM-FM true "Stereo". 1967 was mono-stereo. Bendix was the original manufacturer of AM/FM radios in 1968. *HELPFUL HINT* 1968 and 1969 AM/FM radios are virtually the same except for the shaft lengths. Installing a 1969 AM/FM radio in your 1968 Cougar or Mustang with factory...

F8TBZ Mercury Cougar and Ford Mustang AM/FM stereo radio. This is a non-working unit that has a good crystal and knobs. All knobs seem to move freely. When you look inside the cooling holes on the top of the case you can see mouse droppings. Good unit to use for a modern upgrade core or good for restoration. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get...

Correct three part, telescoping, round base antenna. Comes with round ridged base gasket.*Customer Feedback* "Aloha Don, The antenna showed up with the rest of the USPS sent items. Got in here in three days. Point of installation of antenna. Tie a string to the plug side of the antenna assembly when pulling out from fender so that you can use the string to pull the new antenna plug back through the fender and into the car. Thought of that after pulling antenna out. I was able to use a flexible...

Correct cast aluminum elbow fitting for the rear of the C8AZ-9A486-C smog pump. This elbow will have two single mounting holes. The service replacement elbow (Ford part number D4TZ-9C475-A) has two sets of double mounting holes. Correct Ford part number C8AZ-9C475-A.

1968 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine), or 1969 Boss 302 (G code Eliminator engine) smog pump adjusting arm, casting number C8OE-9B452-A. Ford part number C8AZ-9B452-B, C8AE-B casting number. Bolts sold separate. *Note - Only cars with manual transmissions received thermactor emissions in 1968.

Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.

Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.

Specific to 1968 302-2V, and 302-4V all with manual transmissions - 3 speed or 4 speed. Same tube both sides, sold singly as a bare tube without installation hardware. Two total needed, one for use on each cylinder head. Must use cylinder heads with casting number C8OE-6090-L (302-2V) or C8OE-6090-K (302-4V).Pictured below are some shots of an unrestored J code 302 as taken from a low mile 4spd XR7 parts car. We thought we would post these pictures as a reference for those wanting to know what...

Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder.Thread pitch 1/2" x 20 *Note - Export cars that did not require smog had a much shorter version of this plug installed at the factory. The plug shown here would be...

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

These were installed at the factory on 390 / 427 / 428 equipped cars that were exported to countries that did not require the smog system. They are much shorter than the over the Ford counter service plugs you see in the states that are put on after one removes the smog system.

C8OE-C-SR WCCC Carter service replacement anti backfire valve, but without the outer cover having the concours correct stampings.These units are used, not tested and one should assume they are non-functional.

Screws onto the cylinder head smog tubes. Sold individually, two needed per application. Ford part number C8AZ-9A487-A.

Application small block 289/302/B302 all years 1967 - 1969 with factory Thermactor smog. Spacer for mounting cast iron air pump mounting bracket. Sized .75" O.D. x .73" long. *Note - On Cougars with factory air conditioning 1 spacer is used. On Cougars without air conditioning 2 spacers are used together.

1968 390-4V all with factory manual transmissions and factory air conditioning. Pulley diameter 5.89" inches. Ford part number casting # C8AE-9B480-B. Mounting bolts sold separate.

Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1968 289-2V, 302-2V, and 302-4V all with manual transmissions. Tube dimensions 5/16" O.D. x 1.560" long. C6AZ-9A484-B

Set of nuts and Ferrules for thermactor smog tubes on any 1967 S code 390, 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original or reproduction smog tubes. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the smog tubes and other hardware.

Nice American made reproduction bracket. Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines, all with Thermactor smog pumps. This is also referred to as the low mount alternator mounting bracket. It has the Ford stamped casting number of C8AE-10156-A. Ford engineering number is C8AZ-10156-A.

Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines. This is also referred to as the low mount alternator adjusting bracket. It has the Ford stamped casting number of C8AE-10145-B. Ford part number is C8AZ-10145-B.

Bolt for mounting thermactor smog pump to engine. Must be used in conjunction with thermactor alternator bracket and pump spacer. Bolt dimensions 3/8"-16 x 5.75" long.

This is a 3 bolt Thermactor smog pump pulley with a diameter of 5.49" inches for the Mercury Cougar GT-E with the 427-4V W code engine. C8OE-9C480-A marked on pulley.Ford part # C8OZ-9B447-B.

New Old Stock dog dish style hubcap / wheel cover with the Mercury Man center cap for the Mercury Montego. This very rare optional unit was used in conjunction with the 14x6" 16 hole GT wheel commonly found on Mustangs and Torinos in 1968. This hubcap / wheel cover was offered only in 1968 and rarely seen on a Cougar as it would have only been offered as an over the counter option at your Mercury dealership. The more common application for this unit would be the 1968 Mercury Montego or...

NOS turbine style hubcap / wheel cover for the Mercury Cougar and Montego. These are the same as the 1969 Sports Special / 1968 Dan Gurney hubcap / wheel cover, but have the Mercury logo glued in the center. Ford part # C8GY-1130-G. Fits: 1968 Mercury Montego

NOS Grade A XR7 turbine style hubcap / wheel cover for the Mercury Cougar XR7. This unit was factory installed on the XR7 and was a one year only hubcap / wheel cover that has 22 black ribs. The Mercury MPC states that these caps were not to be sold in Pennsylvania. Ford part # C8WY-1130-D.Fits: 1968 Mercury Cougar XR7

New Old Stock center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. Called an applique. Used only in 1968 on the one style XR7 hubcap. Not sure why it has a 1969 part number, error? Ford part number C9WY-1137-A.

Used chrome / red center cap for the 1967 and 1968 Mercury Cougar and Ford Mustang Equipped with the Wire Spoke Hubcaps / Wheel Covers. Fits:1967 Mercury Cougar1968 Mercury Cougar

Used grade "A" simulated wire spoke hubcap / wheel cover that is in excellent condition with no curb scrapes. This listing is for someone who has removed their center from their current damaged cap and wants to save money by purchasing a cap with no center. The same cap was used on Most all FoMoCo products including but not limited to the Falcon, Mustang, Fairlane, Comet, Galaxie, Montego and LTD, only the center logo changed one car to the next. Ford part # C7WY-1130-C. *NOTE* You will often...

C8OF-9600-B For all 1968 S code 390-4V engines, regardless of GT or 6.5 badges. About 17.00" inches in diameter. Unique feature on this base is the addition of a round vacuum operated valve on the drivers side. Ford part number C8OZ-9600-B *NOTE* Please keep in mind that our hard to find parts like this are not always competitively priced with what you will find on the open market at swap meets and private party sales. Our primary intent in listing these is for our customers to use this...

C8OF-9600-B For all 1968 S code 390-4V engines, regardless of GT or 6.5 badges. About 17.00" inches in diameter. Unique feature on this base is the addition of a round vacuum operated valve on the drivers side. Ford part number C8OZ-9600-B. Our grade B base may have extra holes drilled, possibly dents or rust. Call for details on exact blemishes. Current base is missing the round vacuum valve completely.

This is an open style air cleaner assembly devoid of any snorkel. We send the tops out for a quality rechrome and we can inform you of what dates we have at any one time (date is stamped on bottom, 2 digits year and month, very faint). Most are happy to use the Mustang K code 289 HiPo reproduction air cleaner assembly we sell, which Mercury used on W code GT-E's with 427's. There's also a reproduction unit available.Ford part # C5ZZ-9600-C, C5ZF-9600-D. ...

C9ZE-9600-E Air cleaner base for the 1968 and early 1969 R code 428 Cobra Jet engine option. Additionally one way to identify this air cleaner is the dimple that clears the rear float screw found on the factory Holley carburetor. Early 1969 production is through 2/17/1969, after that date there was a vent added for automatic choke issues. About 16-3/8" inches in diameter. Ford part number C9ZZ-9600-E or C8ZZ-9600-A. Click on images to enlarge. ...

Used grade "A" simulated wire spoke hubcap / wheel cover that is in excellent condition with no curb scrapes, stress cracks in plastic center or pits in die-cast. Ford part # C7WY-1130-C.*NOTE* You will often see this same cap with the Mercury head center and a red background. This cap is not correct for Cougar, but was found on other Mercury products such as the Montego.

Used spinner hubcap / wheel cover for the Mercury Cougar. This was and optional inset spinner that bolted onto your existing hubcap. 1968 was the first year the dealer option was available. Ford part # C7MA-1130-F

Used Grade A XR7 turbine style hubcap / wheel cover for the Mercury Cougar XR7. This unit was factory installed on the XR7 and will more than likely come with a faded center decal. These are almost impossible to find with a nice bright red center on the cars we drag into the yard. You should also expect that the black portions will need to be repainted and that there will be minor scratches around the perimeter, but no curb rash. This is a one year only hubcap / wheel cover that has 22 black...

Used / refurbished center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. These are always faded, so we've "restored" a few with Sharpies, as shown in the picture. Believe it or not, it works pretty well and allows the shiny aluminum to show through the red. Be advised that the sharpie treatment doesn't hold up very well to rain and weather, so this is best for garaged...

These spacers are required to properly mount the trunk lock housing to the trunk. Two required per car, sold individually. Ford part number C7WY-6543565-A. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Reproduction electric rear deck / trunk lid release. Includes electric lock latch, control knob and wiring needed to install.Detailed instructions included.

This is a good used, grade A deck lock housing with nothing included except the studs. There will be no major blemishes or pitting and the cover stop in the bottom corner is intact. This is an impossible part to have restored and look OEM so finding a really good used one is important for a high quality restoration.

Used chrome / black center cap for the 67 - 68 Mercury Cougar equipped with the wire spoke hubcaps / wheel covers.Fits:1967 Mercury Cougar1968 Mercury Cougar

This matched set is actually for a 1968 model Cougar but works just as well on a 67. The only difference being 1967 had squared off edges on the glove box button and 1968 had rounded edges which are safer in a collision.Ford Part # C7SZ-6543505-A/C6OZ-6206281-C or C7SZ-6543507-B (Glove box/Trunk lock kit)

A perfectly working, matched set of trunk and glove box locks with key is getting rather hard to come by these days. These two matching locks are guaranteed to work perfectly. Includes 1968 style glove box lock, 1967-68 Cougar trunk lock cylinder with one "Ford" cut key to the coded to the number imprinted on the glove box lock. This is a matching set with new key. 1967 glove box locks has square edges on the front of the lock. Starting in 1968 the lock had a rounded edge on the front. We also...

This is a decent used, grade B deck lock housing with nothing included except the studs. There will be a couple of blemishes that may include minor pitting but the cover stop in the bottom corner is intact. Perfect for a driver as very little of the chrome shows when this is installed, our reproduction cover will cover almost all of this part in the down position. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info...

This is the factory Ford remote trunk latch as used on luxury cars such as Thunderbird or Lincoln. As you can see from the photo, they are made (and install) exactly like our Cougar trunk latches, but with the addition of a release tab. These can be installed to use either a cable, vacuum, or solenoid release.

Zinc plated, visually correct copies of the original, very prone to failure... We highly recommend buying our good used latches linked here even though they may not look as pretty. No warranty on this low quality off shore part.Replaces Ford Part # C5AZ-6243200-ACheck out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

This is for the person who is missing it all. Includes all you need as seen in the picture and includes the reproduction chrome cover on a good used housing. Let us know in the comments whether you prefer a Standard or XR7 decal installed on the flip up door. Check out our video below showing how to easily remove and re-install your 67-68 trunk latch, lock, and cover plate and some info on getting a new key made. This icon means that we're looking to buy this part!WCCC is a buyer of used and...

Good used cylinder as taken from a 1967 - 1968 trunk lock housing. Will have minor damage but cosmetic only, 100% functional. Ford Part # C7SZ-6543505-A or C7SZ-6543507-B (Glove box/Trunk lock kit) Below are some basics about removing and replacing your lock cylinder and lock cover. When removing the cylinder from the lock housing this button must be depressed to allow the cylinder to slide out the front of the housing.  The only way to depress the button is to have the key in the...

This tiny little spring has a diameter no larger than a pencil. Its function is to attach the deck lock cover to the deck lock housing and to keep the deck lock cover closed. This is a unique spring to this application and rather hard to find.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang. Original Ford part number C8MY-1424-A. About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels.

Original space saver wheel and tire from a 1968-69 Mercury Cougar or Ford Mustang with the elusive 7.35-14 size. These were optional in 1968-69 and pictures show a 1969 date. Never inflated condition. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire.*NOTE* Does not include inflator bottle and valve caps are usually missing. ...

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang.  About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels. We won't always have the used in stock, but the reproduction version is very good.Replaces Ford part number C8MY-1424-A.

Reproduction 6 1/4" Spare Tire Mounting Bolt 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

Ultra rare item, subject to availability. Call about spent cylinders, we actively seek out those too. Our guess is that the contents of an NOS cylinder may be unstable for use.

Reproduction of the protector felt pad between the spare tire and jack handle for the 68 through 70 Mercury Cougar with styled steel wheels. Used only in conjunction with applications that store the jack components on top of the wheel.

New manufactured Tremec T-5z World Class Transmission. Same transmission as installed in Fox Body Mustangs. This is the common transmission for conversions that does not involve extensive modifications to 1967-73 Mercury Cougar or Ford Mustang. Small block Ford V-8 engines only, 289 / 302 / 351W and 351C. Brand new transmission, no core required. 1 year warranty, with recommended synthetic ATF. Flush and fill after first 500 miles, 30,000 miles there after. Bare transmission as shown, no...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to be removed before installation. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2)...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2) Outer Tie Rods, (2) Inner Tie Rods, (1) Idler Arm, (2) Spring Perches. If you...

Designed as a direct-fit OE-style replacement, this modulator valve will fit directly into the factory location of your current Cougar or Mustang valve. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs.