All Available Parts - 1970 Mercury Cougar

Used grade "A" backup / reverse light bezel / housing for the passenger side (right hand) of the Mercury Cougar. Our bezels are the best we can find with no cracks or pits. The chrome will be bright and almost completely free of lines or speckles. The socket and pigtail will be in good condition and there will be no warp-age from over-tightening. There will most likely be thin chrome on the outer edges and other minor blemishes in the chrome. These are perfect for the unrestored, low mile car...

Used grade "B" passenger side (right hand) taillight lens with no heavy scratches, stress cracks or chips. You will want to polish the lens to make it look as good as the one we have pictured with Novus, Mequires or another like plastic polish. You will want to put a 1969 lens on your 1969 Cougar and a 1970 lens on your 1970 as 69 and 70 have different vertical rib spacing on the chrome bezels which creates different wear patterns.  Ford part # C9WY-13450-A. *NOTE* Need help diagnosing a...

Used grade "B" driver side (left hand) taillight lens with no heavy scratches, stress cracks or chips. You will want to polish the lens to make it look as good as the one we have pictured with Novus, Mequires or another like plastic polish. You will want to put a 1969 lens on your 1969 Cougar and a 1970 lens on your 1970 as 69 and 70 have different vertical rib spacing on the chrome bezels which creates different wear patterns.   Ford part # C9WY-13451-A. *NOTE* Need help diagnosing a...

Good used passenger side (right hand) driver grade quality bezel with minimal, light pitting, ready to install and use as-is. If you are planning on sending in cores to be restored this is the level you would want to start with. The pitting found on this grade "B" bezel will be light and almost entirely restricted to the top surface which means it will only be seen when the trunk lid is opened. Passenger side chrome tail light door or bezel. Ford part # D0WB-13449-A for the passenger side....

This is a poor condition bezel with pitting on all surfaces. It is a better than nothing type of part. We do not accept returns on grade C parts. Ford part # D0WB-13449-A for the passenger side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great...

Good used driver side (left hand) driver grade quality bezel with minimal, light pitting, ready to install and use as-is. If you are planning on sending in cores to be restored this is the level you would want to start with. The pitting found on this grade "B" bezel will be light and almost entirely restricted to the top surface which means it will only be seen when the trunk lid is opened. Driver side chrome tail light door or bezel. Ford part # D0WB-13504-A for the driver side. *NOTE* Need...

This is a poor condition bezel with pitting on all surfaces. It is a better than nothing type of part. We do not accept returns on grade C parts. Ford part # D0WB-13504-A for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great...

Used grade "B" driver side (left hand) rear maker light bezel for the Mercury Cougar. We find that these are usually in better condition than the fronts, so we can offer you better quality at a lower price than we can the fronts. These same bezels can also be found on other full size 1970 Mercurys. Ford part # D0MB-15A466-A.

This is a Rebuilding Service - 1969-70 standard core clocks must be received by WCCC prior to shipment. Please call 503-463-1130 if you do not have a core clock. Core clocks for this service are available. C9WY-15000-A 1969 – 1970 Standard Cougar body code 65A, 65C, and 76A, found optionally in the drivers side instrument cluster. This clock was installed on Cougars with decor and standard level interiors and was located within the instrument cluster on the driver side. It has had the original...

Insulator for mounting the ammeter on any 1969-73 Mercury Cougar or Ford Mustang with factory ammeter in gauge cluster. Also used on other Ford cars with ammeter. Casting number C9ZF-10C914. Ford Part # C9ZZ-10C914-A

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps. Even the original RH decals will be in place! These are good quality parts ready to install on your Cougar. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side. ...

Used grade "B" passenger side (right hand) rear maker light bezel for the Mercury Cougar. We find that these are usually in better condition than the fronts, so we can offer you better quality at a lower price than we can the fronts. These same bezels can also be found on other full size 1970 Mercurys. Ford part # D0MB-15A466-A.

These plastic mounting brackets came in black or gray. These kinds of minor differences can often be attributed to different suppliers. We have many that still retain the LH & RH decal for those of you trying to obtain a show car level in your restoration. The backside of this bezel will be marked LH - TOP.D0MB-15A470-B

Unlike the 1970 front side marker lenses we have a good supply of rear lenses in very good condition with and without the studs in place.

This reproduction rear side marker light will fit on either the right or left side of your Cougar.Studs included.Replaces Ford Part #: D0ZZ-15201-R.

Used grade "B" driver side (left hand) front side marker bezel for the Mercury Cougar. The 1970 Ford Torino and Maverick units look similar, but do not have the same angle or depth as the Cougar. These bezels are also unique to the 1970 Cougar. We do not have any of these bezels in "mint" condition, all of our lights will have minor blemishes like the unit shown. Ford part # D0WB-15A441-A.

The Mini Relay Kit has everything you need to add relays to your headlight circuit - without cutting your wiring harness. It is equivalent to installing relays into your main harness like it was done for years, but requires no modification to the wiring harness. The differences between this kit and the full kit are redundancy and controller size. This kit has only one controller with two relays designed to handle up to a maximum of 200 combined watts and uses a wiring harness to control...

Used grade "B" driver side (left hand) backup / reverse light bezel / housing for the Mercury Cougar. These bezels may have slight cracks and pits in the chrome. The socket and pigtail will be in good condition and there will be no warp-age from over-tightening. There will most likely be thin chrome on the outer edges and other minor blemishes in the chrome. These are perfect for a driver quality car. No exchange needed on this unit.Ford part # C9WB-15500-B. Cougar Buying Guide ...

Used grade "B"  backup / reverse light bezel / housing for the passenger side (right hand) of the Mercury Cougar.  These units may have some cracks and pitting in the chrome. There will most likely be thin chrome on the outer edges and other blemishes in the chrome. The socket and pigtail will be in good condition and there will be no warp-age from over-tightening. These are perfect for the daily driver quality car. No exchange needed. Ford part # C9WY-15500-A. *NOTE*...

Used random brand 4001 high beam headlight for the Mercury Cougar. High beam headlights are distinguished by the number 1 at 12 o'clock position and the 2 prong connection on the back. We guarantee these units to work. Basic Ford part # 13007-B.

Driver side rear mounting bracket for the 1970 Mercury Cougar front fender side marker lights. They will not be bent or heavily rusted. The drivers side has an engineering number of D0WB-15A431-A and the passenger side has the number D0WB-15A**** stamped into it.

Used grade "A" driver side (left hand) taillight lens with no heavy scratches, stress cracks or chips. You will want to put a 1969 lens on your 1969 Cougar and a 1970 lens on your 1970 as 69 and 70 have different vertical rib spacing on the chrome bezels which creates different wear patterns.   Ford part # C9WY-13451-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's...

Used grade "A" passenger side (right hand) taillight lens with no heavy scratches, stress cracks or chips. You will want to put a 1969 lens on your 1969 Cougar and a 1970 lens on your 1970 as 69 and 70 have different vertical rib spacing on the chrome bezels which creates different wear patterns. Ford part # C9WY-13450-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Used shutoff valve for the headlight vacuum system of all 1969-70 Mercury Cougars. Also found on 1969-70 Ford and Mercury full sized cars with hidden headlights. Additionally these were also used on 1969-70 midsized Ford and Mercury such as Torino, Cyclone, also with hide away headlamps. This is a black plastic shutoff switch or connector, 1969 cars used a white valve that crumbled from the under hood heat. Note that the indicator tabs perpendicular to the lines means 'open'. Turning the valve...

Grade "A" used backup light lens for driver side 1969 - 70 Cougars. This lens will be free of cracks, chips or scrapes. Ford part number: C9WY-15514-B

Grade "A" used backup light lens for passenger side 1969 - 70 Cougars. This lens will be free of cracks, chips or scrapes. Ford part number: C9WY-15514-A

Grade "B" used backup light lens for passenger side 1969 - 70 Cougars. This lens will show some wear, and will also have a few minor cracks and scratches. Cracks inside the plastic from stress, not contact. Ford part number: C9WY-15514-B

The D0WY-15A434-LSM LED Side Marker Light Adapter kit is required when the C9WY-13A366-AL or the TS-400 Sequential controller is installed with LED front turn signal and LED side marker bulbs on most 1970 and up Ford vehicles. An adapter is required for each side marker light (4 total). This adapter solves the problem where the side marker voltage feeds back through the front turn signal bulb when the running lights or headlights are turned on. When this happens all the rear bulbs may flash...

These plastic mounting brackets came in black or gray. These kinds of minor differences can often be attributed to different suppliers. We have many that still retain the LH & RH decal for those of you trying to obtain a show car level in your restoration. The backside of this bezel will be marked RH - TOP.D0MB-15A432-B

Reproduction 22" pigtail for the 67-69 front turn signal wiring harness. Please Note: The Cougars are wired differently than some Mustangs. On some Mustangs the brown wire goes to a male plug.   This plug is a reproduction of the Cougar plug. Here is an example from the reproduction tail light we sell showing the difference: For installation on a Cougar, match up: Black Wire Black Wire Light Blue Wire Light Blue / Off White Wire Brown Wire Brown Wire ...

Sold as a pair, we suggest you send your cores in advance or at least email us several good quality images if your cores are questionable. If your cores are heavily pitted, cracked or the studs have been over tightened (causes part to dimple / warp) then your cores are not acceptable for restoration. The casting number as seen from the back reads C9WB-15A509-B and C9WB-15515-B. Ford Part # is C9WY-15500-B and C9WY-15500-A

Reproduction replacement halogen bulb for your headlights. This is a clear bulb, "natural white" alternative to the "cool white" bulbs included in our halogen headlight conversion kit. 55 Watt Xenon Halogen H4/9003 bulb. Sold Individually.

Reproduction pair of halogen headlights for any 67 - 73 Cougar or Mustang. These bulbs work for both high and low beam, you simply need to bend one of the tabs back for high beam (see photo above). Keep in mind that you will need a headlight relay kit when installing halogen headlights on your car.  Benefits of switching to halogen bulbs: Brighter lightDramatically improves driver visionOptical lens for a powerful beamLong range high powered lightsCrystal clear glass face with H4 halogen...

We are excited to bring these new reproduction chrome backup light bezels for the 1969 and 1970 Mercury Cougar to the market. The sockets, pigtails and lenses are not included so you will need to gently remove your originals and install them in these bezels. You can find the lenses here.

Reproduction pair of parking light bezels. Applications include 69 - 70 Mercury Cougar, 1969 Ford Mustang Shelby GT-350 and GT500, 1970 Mustang Sport Lamp Bezels, 71 - 72 Maverick Grabber, 1973 - 1974 Maverick (until 8/12/74) and 1971 - 1974 Comet. Replaces Ford part # C9WY-13210-A for the passenger side, C9WY-13212-A for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned...

Reproduction turn signal / parking light housing for the 1970 Mercury Cougar or 1970 Mach 1.  2 required per car, left is same as right. Includes mounting studs, socket, bulb and wiring.

NOTE: WILL NOT FIT 69-73 COUGAR WITHOUT MODIFICATION TO THE CORE SUPPORT OR SPACING THE HEADLIGHT FORWARD APROXIMATELY 1/4" Reproduction complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 69 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and...

Complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 1969 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness.NOTE: From the factory, Ford made the alignment tabs different passenger vs driver side...

This kit is what we recommend to fully convert your 1970 Cougar over to LED Plasma exterior lights. Our WCCC brand LED lights are amongst the brightest on the market and have been specifically engineered with the nuances of the Mercury Cougar sequential system in mind. Keep in mind that over the years folks have become accustomed to very BRIGHT tail lights in traffic and the old incandescent bulbs are not only dim, but they take time to fully illuminate and a split second can make all the...

Flange nut for attaching any 1970 Mercury Cougar or Ford Mustang amber or red side marker lights. 8-32 threaded nut with wide flange. Two per lens, sold individually. 

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps. Could have decals missing, and will have minor pitting. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side.

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps.Could have decals missing, and will have minor pitting. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side.

This pair of tail light bezels have been chemically dipped to remove the chrome and are ready to be painted black for your 1970 Resto-Mod or 1970 ELIMINATOR. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved (mostly on the top edge) before these are paint ready. We hand select premium parts that have minimal defects.If you send cores in for exchange they must be pit free and no...

Flange nut for the 69 - 70 Convertible Windshield Mouldings. Can also be used for attaching any 1970 Mercury Cougar or Ford Mustang amber or red side marker lights. 8-32 threaded nut with wide flange. Sold individually. 

Reproduction master power window switch that goes along with the power window conversion kits. Keep in mind we will buy your old usable factory parts. You might be surprised what those left over clips and wiring harnesses are worth!  Installing this master switch allows you to keep the original look of the crank handles, but allows the driver to control all four windows. All wiring and connectors are included.  ...

This two part black box is what encapsulates your sequential unit for all years 1969-1973. This of course will work with our reproduction sequential unit as well. This box was designed hang from a hook that is welded to the trunk floor just behind the driver side wheel well. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Good used part cut from the trunk of a 69-73 Mercury Cougar. This hook is concealed under the trunk mat and suspends the sequential unit over the trunk drop off area on the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

This is a "better quality" non-concours starter solenoid. It's just one step above our "generic" solenoid also listed on our site. An inexpensive replacement if you are not worried about being 100% correct. More often than not, these lower quality solenoids fail within a year or two so we always recommend buying original FoMoCo. Replaces Ford part # B6AZ-11450-A, C7AZ-11450-A & D2AF-11450-A.Cougar Applications:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury...

This Autolite capacitor is stamped with part number C6OA-18832-A. It attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. All Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory. Starting in 1972 there is a Motorcraft version which has a...

Finally a fast easy way to hook up the Pertronix Ignitor©! The Ignition Power Relay installs next to the starter solenoid with a supplied self-drilling, self tapping screw. Each wire is the right length and comes with the correctly sized terminal already Installed. Simply connect two wires at the solenoid and connect the Ignitor to the red power wire. The Pertronix Ignitor© is a 12 volt device that must be powered during crank and run. Many installers mistake the coil positive for a 12 volt...

Reproduction 2 speed windshield wiper switch for the Mercury Cougar or Ford Mustang. These "off shore" units are what other vendors offer, but they pretty poor quality and spotty at best. We highly recommend that you buy our good used units which you can get right here.

Oil pressure switch with press on wiring connector. 1967-73 Mercury Cougar and Ford Mustang. This is the warning light style of sending unit. Cougar body code 65A and 65C, excludes Eliminator. Additionally this sending unit also fits 1970 and newer Ford Maverick and Mercury Comet, 1968-69 Lincoln with 460 engines, and 1967-71 mid sized Ford and Mercury cars such as Cyclone, Fairlane, and Torino.Check out the video below on our new gauge tester: ...

Angled cup or retainer, used with the wiper switch, it locates and maintains the angle to the dash from behind. 1969 and 1970 are different, obvious when you realize that the flat spot is indexed differently between the two years. Ford part numbers: DOZZ-17C491-A, D0ZB-17C491-A.

Good used windshield wiper switch for any 1970 Cougar or Mustang. Marked DOZB-17A553-A on the back. This is the two speed variety, the 1970 switch has a longer shaft than the 1969 version.

1969-70 Mercury Cougar XR7 dash 3 pin on / off rocker switch. Suitable for any position, MAP COURTESY PANEL or ACCY. Switches sold pit free on the chrome. Switches guaranteed to work, but are likely stiff. Electro solvent usually helps with that sticking condition, see product label for directions prior to use. These are sold individually and in most applications four are used except in 1970 xr7 convertibles or or 1970 xr7 coupes with rear defog. In these cases a different design of switch was...

Used roof mounted switch that is rather delicate. As you can see from the pictures, the chrome coating has started to peel slightly. 

New Old Stock NOS windshield wiper switch for any 1970 Cougar or Mustang. Marked DOZB-17A553-A on the back. This is the two speed variety, the 1970 switch has a longer shaft than the 1969 version.

New Old Stock 1969-70 Mercury Cougar XR7 dash 3 pin on / off rocker switch. Suitable for any position, MAP COURTESY PANEL or ACCY. These are sold individually and in most applications four are used except in 1970 xr7 convertibles or or 1970 xr7 coupes with rear defog. In these cases a different design of switch was used and the surrounding bezel would be labeled "Top" or "Defog" in the farthest position to the right. The fourth switch is never used on the 1969 xr7, it is just there to...

For AM radio optional rear speaker. Ford part number C9ZB-18A900-BOverall length: 11' 7"

Grade "A" harness that runs from the passenger side door jamb to the courtesy / C-Pillar light. This harness is only needed if you have a Standard model car. NOTE: All XR7's would have already come equipped with his harness.

This used plug end will work on your 69 - 70 Standard or XR7 as well as the 69 - 70 Mustang. This plug housing is used to connect the under dash main loom to the gauge cluster.*Does not include wires

Used wire harness for the 69 - 70 STANDARD Cougar. This main harness connects to the harness for the convenience lights on the warning light panel in the center of the dash. Ford part number C9WY-10C877-C. Used in conjunction with the two convenience light harnesses / sockets found here. The convenience package was offered on Cougars that were non-XR7.

Used engine lift hook or hoist bracket for all 1970-73 351C engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. H code 351C-2V and M or Q code 351C-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We also...

Used engine lift hook or hoist bracket for all 1969-70 351W engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. H code 351W-2V and M code 351W-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We also sell...

Used oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

Reproduction oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

Featured in this kit are all the basic items you need to convert your small block 1970 Cougar or Mustang from a 20" wide radiator with a fixed four blade fan to a 24" wide radiator with 3 cores and the MAXIMUM cooling big block, high performance 7 blade clutch fan.  This setup was used on the highest horsepower drive-trains of the day including the Legendary 427 Side-Oiler equipped GTE and the 428 SCJ Drag-Pak equipped Cougars and Mustangs.  This might sound like overkill for your...

These replacement "Yellowtop" ignition coils are copies of the original. Nice reproduction cosmetically and functionally. This is a very prominent piece and a must have when trying to detail your engine compartment properly. Replaces Ford part # B6A-12029-B.   Note, no decals are included. Check the website in related items.

Reproduction distributor cap for the 1967 - 1973 Mercury Cougar or Ford Mustang 

A needed part for giving your car a tune-up.

Reproduction Distributor Condensor for the 1967 - 1973 Mercury Cougar and Ford Mustang

Correct Autolite 24 spark plugs for all 1970-73 351 Cleveland engines. This is what Ford installed originally from the factory. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.

Correct Autolite 45 spark plugs for all 1967-73 289/302/351W/390/428CJ engines. This is what Ford installed originally from the factory. BF32 crosses over to this spark plug. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.

C8AF-12A022-A For all 1967 - 71 V-8 distributors. Concours correct head stamping. Brass plug for the stock Autolite distributors. Installs as shown.

Reproduction single port vacuum advance for most all 1967-71 Ford V-8 engines. Fits Ford's brand of Autolite and Motorcraft distributors found on all 1967-71 Mercury Cougar and V-8 Ford Mustangs.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory H code 351-2V V-8 engine. 351 Windsor engine rated at 250 Hp with 9.5:1 compression ratio in 1970. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex plate. Intake manifold and oil...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory M code 351-4V V-8 engine. 351 Cleveland engine rated at 300 Hp with 11.0:1 compression ratio in 1970. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, exhaust manifolds, fan, distributor, accessories, pulleys, and flex plate. Intake manifold and...

Used core distributor for 1969 Mercury Cougar and Ford Mustang with H code 351W-2V and automatic transmission. Core distributors will have correct stamping of D0AF-AC. Original Ford part number D0AF-12127-AC. 351 Windsor engines use a smaller distributor gear (about 1-1/4"), Cleveland.distributor gear is about 1-7/16" in diameter.

Concours correct Autolite spark plug wires for any 1969-70 Mercury Cougar Eliminator or Ford Mustang with Boss 302 engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q69 (second quarter 1969) on the 7mm wires. Orange spark plug boots on this set.

Concours correct Autolite spark plug wires for any 1970 Mercury Cougar Eliminator or Ford Mustang with 351W engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q69 (second quarter 1969) on the 7mm wires. Black spark plug boots on this set.

Concours correct Autolite spark plug wires for any 1970 Mercury Cougar Eliminator or Ford Mustang with 351C engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q69 (second quarter 1969) on the 7mm wires. Orange spark plug boots on this set.

Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...

Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

Reproduction replacement hold down clamp for the distributor on any 67 - 73 Cougar or Mustang. Sold individually, 2 needed per car.

Used ported vacuum switch with filter. Unique piece, unknown application, definitely found on a 1968. Current offering are dated 8-67, 6-68, 5-68, 7-69, 8-69. Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is...

Exact copy reproduction concourse correct distributor cap with raised Autolite logo. Good for all 67 - 73 Cougars and Mustangs. A must have for anyone building a show car.

Distributor hold down bolt. All V-8 engines.1967-73 Mercury Cougar and Ford Mustang. 5/16 x 7/8" bolt, 1/2' hex head.

Used 1969 351W coil mounting bracket. This version of the bracket is specific on the 351W and allows extra room for the oil dipstick. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. Listed in the...

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. 1969-70 Mercury Cougar Eliminator with Boss 302 and 1969-70 Ford Mustang with Boss 302 engines.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-69 Mercury Cougar or Ford Mustang with S or X code engines. Additionally fits 1968-70 428 Cobra Jet engines. This kit is for the distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-69 Mercury Cougar or Ford Mustang with S or X code engines. Additionally fits 1968-70 428 Cobra Jet engines. This kit is for the distributor vacuum advance units with dual nipple connections. Often times it is the ones with automatic transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-70 Mercury Cougar or Ford Mustang with 289, 302, and 351W engines. This kit is for the distributor vacuum advance units with single nipple connections. 

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-70 Mercury Cougar or Ford Mustang with 289, 302, and 351W engines. This kit is for the distributor vacuum advance units with dual nipple connections. 

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1970-73 Mercury Cougar or Ford Mustang with 351C or cleveland engines. Distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.