Interior

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

This is the arm rest base for the driver or passenger side on any 1971, 192 or 1973 Mercury Cougar with standard interior as well as some Mustang trim levels.  Also fits multiple other Ford /  Mercury cars of the same vintage.Replaces Ford Part Number: D1AB-5724144

These plastic backing plates are found on all 71-73 Cougars with standard interior. Since most Cougars had decor or XR7 interior we have a limited supply of these and cannot guarantee we can get the color you desire, but we will try to accommodate. Right is the same as left. Keep in mind these same parts can be found on many Fords and Mercury's throughout the 70's

If you have an early 1969 your hinge was a flexible plastic strip that long ago began to fail. Often you will see generic piano hinge in its place. This is a correct reproduction of the hinge used in the latter part of 69 and all of 70 Cougar and Mustang consoles. Replaces Ford part # C9ZZ-6306050.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # D1ZZ-6524101.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # D1ZZ-6524100.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

This is the correct pad for your 69-70 Cougar unless it is the XR7 which uses the three hump lid. Unlike some you may have seen in the past (for less $) this has the correct stitching on the front edge and is a much better fit. Comes in black only. All of our reproduction 69-70 consoles utilize this premium quality pad.

This is the economy version of the pad for your 69-70 Cougar unless it is the XR7 which uses the three hump lid. This is the same pad sold at many Mustang shops. It does not have the correct stitching on the front edge and is a bit short, but fully functional. Comes in black only.

This is a very rare find. Grade B used 1969 XR7 / Shelby only.Notice how the three humps stand taller and rounder than the reproduction. Limited colors on hand, please let us know which color you desire and we will try to accommodate. Pictured pad is for reference only. Grade B will have blemishes and or small cracks. Plan on repainting with SEM or other type of vinyl paint for best matching results.

Reproduction arm rest pad / center console lid for the Mercury Cougar XR7 or Ford Mustang. This is the most correct XR7, Shelby, late Mach I and late deluxe Mustang interior three hump lid on the market and the quality is average at best. The length is shorter than the original and the humps are not as high.Replaces Ford part # D0ZZ-6506024. ...

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. NOTE: The color on this armrest is incorrect and is a darker shade of brown, rather than the correct ginger color. Replaces Ford part # D1ZZ-6524101.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. NOTE: The color on this armrest is incorrect and is a darker shade of brown, rather than the correct ginger color. Replaces Ford part # D1ZZ-6524100.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

More accurate reproduction of the 1967 and 1968 XR7 Armrest Plugs. The difference in this pair, as compared to the set of four we sell, is that these will have a more accurate flat headed finish to them and will sit flush with the armrest face. Only available in Black. Sold as a pair Replaces Ford part # C7ZZ-6524056 or C8ZZ-6524056.

Mini console or consolette ashtray, for 1971-73 Mercury Cougar or Ford Mustang. Has ball bearing rollers, and dual cigarette extinguishers. Color keyed to the console and interiors, include a desired color in the notes or comments section of your online order. We will try to find your color, easy to paint with vinyl paint.

Used ash tray for the 1967 Mercury Cougar or Ford Mustang. This unit will come as taken from a Western parts car. Original FoMoCo construction, built to last. There is a slight difference between the 1967 and 1968 dash openings for these ashtrays. This 1967 ashtray painted face, measures 7-1/8 inches long. The 1968 version is 6-13/16 inches long measured with a flexible ruler.Replaces Ford part # C7ZB-6504810.

Used ashtray for the 1968 Mercury Cougar or Ford Mustang. This unit will come as taken from a Western parts car. Original FoMoCo construction, built to last. There is a slight difference between the 1967 and 1968 dash openings for these ashtrays. This 1968 ashtray painted face, measures 6-13/16 inches long. The 1967 version is 7-1/8 inches long measured with a flexible ruler.Ford part # C8ZB-6504810.

Ashtray only for 1970 Mercury Cougar and Ford Mustang, has the pebble grain texture. You would need to freshen up with your interior color.

Ashtray only, for 1970 Mercury Cougar XR7, this has the burl wood and chrome trim.Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts!

Grade A used, will have at most a couple of small blemishes, includes the ash tray receptacle. We sometimes have grade B used, see related items.Replaces Ford part number C7ZB-65048A42-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot...

Chrome finish is average at best. Grade B used, will have pits and or obvious blemishes in the brushed chrome, includes the ash tray receptacle. We sometimes have grade A used, see related items. Replaces Ford part number C7ZB-65048A42-A.

Used ashtray assembly for use in 1969 Mercury Cougar and Ford Mustang without center consoles. Pebble grain finish, you paint to match your interior color. Cigar lighter and ash tray knob not included. Illumination light socket and wiring available separately.

Under dash installed ashtray for all 1969 Mercury Cougar and Ford Mustang without console. Ashtray drawer combination only used in 1969, smaller version than the 1970 ashtray. Pebble grain finish you paint to match you interior color. Knob and bezel not included. Ashtray only.

Ashtray only for 1969 Mercury Cougar XR7, this has the burl wood and chrome trim. Chrome knob and bezel not included.

Under dash ashtray assembly for 1970 Mercury Cougar XR7, has burl wood and chrome trim. For 1970 the cigar lighter moved to the position where the ignition switch used to be in 1969. Indicator light and wiring assembly not included. Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts! ...

High quality rubber molded around a flexible steel insert. Insert is cadmium plated to prevent rust. A popular replacement item, as they always wear. While this unit also fits the 1965-68 Mustang, it is only correct for the 1968 Cougar XR7-G. Replaces Ford Part #: C5ZZ-7D351 Check out our video on rebuilding your shifter below: ...

This is for your automatic transmission 1970 Cougar. The 70 is unique over the 69 in that it does not have a provision for your seat belt buckles. This part does not require an additional woodgrain bezel that affixes to the top. Absolute perfection in every detail, if all reproductions were this nice there would be no market for used parts.

Don't throw away those panels just because the backing boards are broken and warped! You cannot buy reproduction panels for the 67-70 Mercury Cougar, but you can get this pair of backer boards. If your vinyl is good, then you will want to put the work into them. These are not a quick fix, they do take time to install but the end result is worth it. These will work on your 67-68 XR7, Decor or Standard model as they are cut for all models and all options (i.e. manual remote mirror, courtesy...

Don't throw away those panels just because the backing boards are broken and warped! You cannot buy reproduction panels for the 67-70 Mercury Cougar, but you can buy this pair of backer boards. If your vinyl is good, then you will want to put the work into them. These are not a quick fix, they do take time to install but the end result is worth it. These will work on your 69-70 Xr7, Decor or Standard model as they are cut for all models and all options (ie manual remote mirror, courtesy...

Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part #: C5AZ-6223370-A.

Protects quarter panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part #: C4SZ-6323370-A.

Reproduction steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. Outside diameter: 1 1/2" Inside diameter: 1 1/4"*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used lower steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. The upper bearing can be found here. Outside diameter: 1.500"Inside diameter: 1.060" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Very nice replica of the cigar / cigarette lighter bezel for the 1970 Mercury Cougar or Ford Mustang. Replaces Ford part # D0ZZ-10852-L.

This replaces that rusty, scratched bezel in your 1969 Cougar or Mustang center console. Included is the support bracket for the backside.

Used cigar or cigarette lighter bezel for 1971-73 Mercury Cougar and Ford Mustang. Ford part # D1ZZ-15052-A and D1ZB-15053-A

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars with factor air conditioning. Cars with only the heater option used a different bezel that has a hole for the vent cable. This bezel is blank, and only has the rectangular hole for the air conditioning vent register.Replaces Ford part number D1WB-65044A13-BC (cast on the part) or D1WY-6504393-B

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars without factor air conditioning. Cars with only the heater option had dual fresh air vents. This bezel is for the driver side fresh air vent register and control cable, it has a molded hole for the vent cable.Replaces Ford part number D1WB-65044A13-AC (cast on the part) or D1WY-6504393-A.

Dash color painted steel bezel that houses the courtesy lights on all 1969-70 Mercury Cougar XR7's. This is the bezel that says MAP COURTESY PANEL ACCY. Sold pit free, often times we can select your desired color, but plan on detailing them if your undergoing a restoration. Mention your color in the comments section of your order. Replaces Ford part number C9WB-10964.

Dash color painted steel bezel that houses the courtesy lights on all 1969-70 Mercury Cougar XR7's. This is the bezel that says MAP COURTESY PANEL ACCY. Sold pit free, often times we can select your desired color, but plan on detailing them if your undergoing a restoration.Replaces Ford part number C9WB-10964. During assembly of your switches, note that the pins need to be on top. Switches and wiring harnesses sold individually. ...

Dash color painted steel bezel that houses the courtesy switches with DEFOG on all 1970 Mercury Cougar XR7's. This is the bezel that says MAP COURTESY PANEL DEFOG. May have some small pits, depending upon stock on hand. Plan on detailing them with your interior color for best results.Replaces Ford part number D0WB-10964-B. During assembly of your switches, note that the pins need to be on top. Switches and wiring harnesses sold individually. ...

Dash color painted steel bezel that houses the courtesy switches with convertible top on all 1970 Mercury Cougar XR7's. This is the bezel that says MAP COURTESY PANEL TOP. May have some small pits, depending upon stock on hand. Plan on detailing them with your interior color for best results.Replaces Ford part number D0WB-10964-A. During assembly of your switches, note that the pins need to be on top. Switches and wiring harnesses sold individually. ...

Emergency flasher switch bezel for the side of fixed steering columns (non-tilt). For all years 1967 1968 1969. Paint to match your interior. Compared to the reproduction version of this bezel, there is a difference. "Emergency Flasher" lettering is much heavier on the originals, plus they came color matched to the steering columns. We can often times supply your desired color, please include color needs in the comments section. Ford part number C9OZ-15C580-A.

Emergency flasher bezel for the side of the tilt steering column. Reproduction bezel in black. Replaces most all tilt swing steering columns from 1967-69. Replaces Ford part number C9AZ-15C80-A, and an earlier part number starting that was likely C7SZ-15C580-A.

Complete grade "A" bezel with perfect woodgrain and aluminum surround. The 1969 bezel is unique from 1970 in that 1970 had a curved cut-out for the larger diameter column. Notice the circular rings around the gauges are not discolored on this premium grade part.Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts! ...