Interior

Xr7 models featured rocker switches in the center of the dash, standard Cougars had warning lights and Eliminators had this block off pad. This reproduction fits perfect and has been needed for a long time. Replaces Ford Part #: C9WY-10854.

Reproduction front armrest in blue for the Mercury Cougar. This unit is ambidextrous, meaning it will fit either the driver (left hand) or passenger (right hand) sides. Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard...

This dense, closed cell foam adheres to the back of your 1967 seat frame. This is a used part, carefully (but not always perfectly) removed from an original frame. No water or pest damage, bucket and bench seat are the same as well as right and left.Sold individually.

New screw with a correct 3/8 inch hex head for installing all armrests for all years.

12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used to mount the vacuum actuator to the column in 1967 and the actuator to the bracket on 68-69. Also used to mount the steering column relay and vacuum release valve in 1968-69.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last...

New old stock seat belt bolt, has the "A" marking on the head. 1-3/8 inches long bolt for seat belts. Torks head, not sure of the exact placement in the car. Ford box has 'Campaign M9D Bolt' as the description.  Ford part number 382624-S100.

Good used original seat belt bolt. There were a few different variations of this bolt, some were stamped with a D with triangles, some with E and three triangles and others had no stamping at all. 13/16" hex head, two inch bolt with a 7/8 inch shoulder. 

Used in multiple applications front and rear lap belts. Inner and outer, marked with a letter "B" in at least three known fonts. 1-3/4 inches long, 1/2 inch shoulder, Torx 50 tool for installation and removal.

Front retractor bolt, used in conjunction with two rubber spacer / washers and one washer. The two rubber washers go on either side of the re-tractor mounting hole and the metal washer is against the inner rocker.

Front inner bolt that attaches female portion of the lap belt to the transmission tunnel. Used in conjunction with a silver, fat washer that is slightly cupped.

Used early version of the long seat belt bolt for the Mercury Cougar or Ford Mustang. This early version has faint markings on the head of the bolt as where the later versions have more prominent markings. 13/16" hex head,  two inch bolt with a 1/2 inch shoulder. Can be either smooth headed or have an "E".

Used on inner and outer rear seat belt bolts, four per car in 1970 -1971 and used only on the inner rears in 72 - 73 due to the addition of rear retractors. Used in conjunction with two red washer / spacers, marked with three known font styles of the letter "A". 1-5/16 inches long, Torx 50 is the tool for installing and removing.

Used early version short seat belt mounting bolt to mount the front retractor to the inner rocker panel and used in conjunction with a large washer. This is an early version of the the seat belt bolt with faint or no markings on the head, the later versions are longer, and have much more prominent head markings.13/16" hex head, 1-1/8inch bolt with a 3/16 inch shoulder.

Rear seat belt bolt, four per car used in conjunction with two red washer / spacers. 13/16" hex head, 1-1/4 inch bolt with a 3/16 inch shoulder. Strong "A" on this one as shown. There is another version of this same bolt with a light "A" or smooth head and no markings. See related items.

Used to mount the front retractor to the inner rocker panel. Used in conjunction with a large washer. 13/16" hex head, 1-1/2inch bolt with a 1/2 inch long shoulder. May or may not be marked with a letter "C".

Two per car, identified with the letter "D" in three known fonts. This bolt was used in conjunction with a chrome spacer / washer that is also marked with the letter "D". 1-1/2 inches long, 1/4 inch shoulder, use a Torx 50 for installation and removal.

Good used original seat belt bolt. There were a few different variations of this bolt, some were stamped with a F and others had no stamping at all. 13/16" hex head, 1-7/16 inch bolt with a 1/4 inch shoulder. 

Replaces Ford Part # 382626-S Sold individually

Screw for attaching steering column plate to floor board. Usually 4 are needed and go through the carpet and into the toe board. Correct finish and style of AMK bolt. Length 1 3/16"#14 Threads

Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually. 

Concours correct for 67, but a nice dress-up item for 68-73. Replaces Ford Part # 382627 Four bolts, four washers and eight rubber washers in mounting kit.

Pictured is a complete set of 1967 Hex bolts, spacers and washers. We will make sure they are damage free, rust free, and a complete set removed from the same year of Cougar as yours. There were minor and major changes almost every year so you will want to select the right year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! 

Reproduction bolts and washers for the shoulder belts on any 1969-73 Mercury Cougar or Ford Mustang. Includes 2 each of the "D" bolts and chrome thick washers. Quality AMK kit F-3563.

These pamphlets were found buried in the back room of a San Jose California Lincoln-Mercury dealership. There was no reason to keep them after the warranty expired so most were discarded long ago. Great for that person who likes original documents. Limited quantity.

Support brace between the bottom of the steel lower dash panel and the cowl top. Fits 1969-70 Mercury Cougar and Ford Mustang with either air conditioning or without air conditioning. Ford part number C9ZB-6504672-A.

One end attaches to the right of the brake pedal support, and the other to the dash panel. Original Ford part number C9ZB-6504510.

Sold as pair on exchange or outright. Only cores with minimal corrosion can be considered for exchange. Ford part number C7AZ-6204144-A, casting number as seen on the backside reads C8AB-6204122-B.  Does not include smaller rod for the sun visor tips.  Sold as a pair.

Reproduction Sun Visor Bracket & Rod for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang. Great quality and fit, left and right use same part, sold separately. Replaces Ford part # C7AZ-6204144-A.

Used cigar / cigarette lighter and ashtray mounting bracket. Mounts behind the dash on 1967-68 Mercury Cougar and Ford Mustang. Holds the cigar or cigarette lighter element, and the ashtray receptacle. 

One year only bracket used on both fixed and tilt column cars.

Lower steering column mounting bracket. 1967-68 Mercury Cougar and Ford Mustang. Right and left halves with original fasteners. Rubber gasket sold separately.Ford part number C7ZZ-65017A50 and C7ZZ-65017A51.

Used tilt column vacuum can bracket for the 1968 Mercury Cougar *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

One year only design.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used bracket for the vacuum reservoir for the tilt / tilt away steering column found in the Mercury cougar or Ford Mustang. This specialized little bracket is used to mount the tilt / tilt away vacuum reservoir in place. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement...

Used bracket for the vacuum reservoir for the tilt / tilt away steering column found in the Mercury cougar or Ford Mustang. This specialized little bracket is used to mount the tilt / tilt away vacuum reservoir in place. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement...

Used windshield wiper mounting bracket for any 1967-68 Mercury Cougar or Ford Mustang. Part of the wiper motor assembly in the Master Parts Catalog, so no Ford number found.

Used mounting tab or bracket, that is embedded into the dash pad below the instrument cluster for attaching the lower dash filler. These can be glued back into the foam with adhesive. Right and left side pieces are different, this one attaches to the lower left side. The companion bracket is also available.

Used mounting tab or bracket, that is embedded into the dash pad below the instrument cluster for attaching the lower dash filler. These can be glued back into the foam with adhesive. Right and left side pieces are different, this one attaches to the lower right side. The companion bracket is also available.

Unique to power brakes and only with 1967 Cougar steering columns. Pedal shipped bare, picture may show hardware and pedal pad with trim. *Note* You will have to drill holes in your existing pedal hanger to accommodate the power brake pedal. Since systems with a vacuum booster take less effort to activate than systems without, a different folcrum point is used that does not utilize built in bushings into the hanger. Please refer to our power brake pedal hanger listing for measurements on where...

Longer arm than manual brake pedals. Designed to work with the wider, 1968 collapsible steering column. Will work in 1967 Cougars if converting to 1968 disc brakes. Pedal shipped bare, picture may show hardware and pedal pad with trim. *Note* On some 1968 Cougars you will have to drill holes in your existing pedal hanger (many are pre-drilled) to accomomdate the power brake pedal. Since systems with a vacuum booster take less effort to activate than systems without, a different folcrum point...

Longer arm than drum brake pedals. Works only with 1970 power brake booster rod. Pedal shipped bare, picture may show hardware and pedal pad with trim. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you...

Longer arm than drum brake pedals. Comes with all mounting hardware. Pedal shipped bare, picture may show hardware and pedal pad with trim. Most of these pedals are dated as shown. It makes it fairly easy to identify them by year.

For use with a clutch pedal. Longer arm than drum brake pedals. Comes with all mounting hardware. Pedal shipped bare without pedal pad with trim.

Warning lens indicating "BRAKES", attaches to the tachometer on any 1967-68 Mercury Cougar XR7. This is a red back lit lens, it tapes onto the back side of the tachometer bezel. Ford part number 10A936

Core bucket seat frame bottom for the Mercury Cougar or Ford Mustang. This unit is the same from driver side (left hand) to passenger side (right hand) and is the same whether you have a standard, decor or XR7. The base is the same whether you have center release or side seat back release. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These units will be solid core frames taken from a Western parts car but keep in mind they will always have a...

Core driver side (left hand) and passenger side (right hand) bucket seats for the Mercury Cougar or Ford Mustang equipped with the decor interior option. These bucket seats are sold as a pair, but if you need the passenger side only, call us and we can offer you a substantial discount. If you need a driver side bucket only we cannot give you a price break, but the shipping will in fact be cut in half. The foam almost will always be deteriorating or even missing. They will be solid core frames...

Core driver side (left hand) and passenger side (right hand) pair of bucket seat cores for the Mercury Cougar XR7. The foam almost will always be deteriorating or even missing. They will be solid core frames taken from a Western parts car and from our experience are MUCH better quality than the Chinese made reproductions on the market. Seat tracks are sold separate. Seat hinge covers and hardware available separately.