Front Drum

Used wheel cylinder link pin. This pin protrudes from both ends of the wheel cylinder and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Fits all drum brake wheel cylinders, front or rear drum brake systems. Two needed per wheel cylinder. Sold individuallyFord part number B7A-2042-A.

Reproduction wheel cylinder link pin. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Sold individually. Ford part number B7A-2042-A.

Reproduction set of wheel cylinder link pins. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place.Sold as a set of four.

Reproduction master cylinder for the Mercury Cougar and Ford Mustang equipped with drum brakes. This unit is brand new, not rebuilt, and made from high quality American made parts.

Reproduction master cylinder for the Mercury Cougar and Ford Mustang equipped with power drum brakes. These are brand new units, not rebuilt, and are made from high quality American made parts. WARNINGS: Do not attempt to use a 1970 booster on a 1967-69 Cougar as failure will occur within minutes! Never bleed your brakes on a power brake car with the car running. The pedal will over extend the rod into the booster and break internal parts. This is not covered under warranty. ...

This kit includes the 4 fine threaded "T" shaped studs (with nuts) that mount the backing plate to the spindle and the plate that goes on the inside of the backing plate. These are used parts that are not damaged or corroded, taken from a Western parts car.

NOS brake pedal for the Mercury Cougar or Ford Mustang equipped with power drum brakes. This unit will work with disc brake Cougars and Mustangs, but is not correct. That is because the power drum pad has "power brake" inscribed on the pad where the disc brake version has "disc brakes." Also, the 1967 version is narrower than 1968-73 piece.Ford part # C5ZZ-2457-E.

Reproduction brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. These have 1/2 inch holes in them, like the originals.Replaces Ford part number C4UZ-2028-A.

Kit for rebuilding your drum brake distribution block on your Mercury Cougar or Ford Mustang. Special square O-rings are made from EPDM (Ethylene Propylene 70 Durometer) which is specifically designed to withstand chemical degradation caused by prolonged exposure to brake fluid.*Customer Feekback*"You guys are awesome, I couldn't find a rebuild kit for my Galaxie's brake distribution block anywhere else! Thank you!" Henry M.Here’s a video to help you rebuild the distribution block so that you...

Reproduction driver (left hand) side drum brake self adjustor repair kit for your Mercury Cougar or Ford Mustang. This kit contains all the parts necessary to refurbish the self adjusting mechanism on drum brakes. Includes new cable and guide, ratchet, spring, and all necessary small parts. Kits include everything for one wheel.

Reproduction passenger (driver hand) side drum brake self adjuster repair kit for your Mercury Cougar or Ford Mustang. This kit contains all the parts necessary to refurbish the self adjusting mechanism on drum brakes. Includes new cable and guide, ratchet, spring, and all necessary small parts. Kits include everything for one wheel.

Wheel seal for both front disc and front drums, 1967-73 Mercury Cougar and 1967-73 Ford Mustang with V-8. Seals sold individually. Two of these are needed, one for each side on the front.

Shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. This is a reproduction of the 1968-70 shaft which had a Ford part number of C8AZ-2478-A. This version uses a special spring clip. We also sell the 1967 shaft, which uses a hairpin clip and washer.

Shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. This is a reproduction of the 1967 shaft uses a hairpin clip and washer on the end. We also sell the 1968-73 shaft, which uses a spring clip.Ford part number of C6AZ-2478-A.

Used shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. We do not have the spring clip available. Ford part number of C8AZ-2478-A. 

Contains all the replacement springs and hold downs required to do a professional brake job on drum brakes, front or rear. Kit includes enough parts for two wheels.Fits 10 x 2, 10 x 2-1/4, and 2-1/2 inch drum brakes.*Hint - Use your camera phone to take pictures of your brake assembly prior to disassembly, and do one side at a time. Sort out and match all of the springs up exactly, they are side and position specific.*NOTE* Kit does not include hardware for rear emergency brakes. ...

Reproduction drum brake spring and hold down kit for Mercury Cougars or Ford mustangs equipped with 10"x2" drums. This kit contains all the replacement springs and hold downs required to do a professional brake job on 1969-73 Mercury Cougar or Ford Mustang 10" x 2" rear drum brakes. Kit includes enough parts for two wheels. *Hint - Use your camera phone to take pictures of your brake assembly prior to disassembly, and do one side at a time. Sort out and match all of the springs up exactly,...

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes and an automatic transmission. This unit is not for cars produced after 6/25/1972. Ford part # D1ZZ-6501508-C.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with an automatic transmission and manual drum brakes. This unit is for cars produced after 6-25-1972. Ford part # D3ZZ-6501508-C.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with a manual transmission and manual drum brakes. Not to be used in cars produced before 6/25/1972. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and unused condition. Ford part # D3ZZ-6501508-A.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and in unused condition. Ford part # C9ZZ-6501508-A. *NOTE* Manual brake supports are different. Manual brake supports have four threaded nuts swedged to...

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and unused condition. Ford part # D0ZZ-6501508-A. *NOTE* Manual brake supports are different. Manual brake supports have four threaded nuts swedged to the...

Reproduction brake pedal hanger for manual brakes. Can be modified to work for power brakes.

This used brake pedal support bracket is the correct hanger for a 1967-68 Mercury Cougar or Ford Mustang with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint, unused condition. Ford part # C7ZZ-6501508-C. *NOTE* Manual brake supports are different. Manual brake supports have four threaded...

This used brake pedal support bracket or brake pedal hanger is for the Mercury Cougar or Ford Mustang equipped with power disc or drum brakes. We have carefully shown the mounting position of the pedal so you can drill your existing manual brake pedal hanger when converting from manual to power brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means...

Reproduction brake pedal hanger also known as the brake pedal support for Mercury Cougar and Ford Mustang.

Reproduction brake pedal hanger also known as brake pedal support for Mercury Cougar and Ford Mustang.

Used brake light warning switch for Mercury Cougar or Ford Mustang and Torino and is identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Fits most if not all 1968-69 Ford and Mercury cars.Ford part # C8AZ-2B264-A.

Sold individually, phosphate & Oil (gray-black).

New wheel stud replacement for all Mercury Cougars equipped with front drum brakes. Pretty much fits most other front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only, serrated 2" stud with correct 1/2 x 20 threads. These are slightly longer in length than the stock ones, this will allow the alloy wheels to fit the Classic Cougars.Replaces Ford part # C30Z-1107-A.*NOTE* You should use a press to remove and/or install the new studs.

New front inner wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 1.25 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A smaller outer bearing and this inner bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...

New front outer wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.75 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...

Reproduction passenger side (right hand) front wheel cylinder for 10 inch x 2-1/2 inch drum brakes. This unit fits in a 1-3/32 inch hole on the brake backing plate. Replaces Ford Part # C6OZ-2061-B or C9TZ-2061-B.

Clever tool that keeps the piston stationary in your brake distribution block. It is as simple as centering the piston and screwing in this tool, of course your have to catch the groove in the piston. Leave in until brakes are completely bled and functioning. Remove and install your brake warning light switch.

Steel tubing features tin/lead coating and plated zinc chromate fitting and are exact copies of the originals with color coded fittings. New copy of the 1968-69 Mercury Cougar and Ford Mustang manual drum brake master cylinder lines. 

Replacement brake pedal pad trim for the Mercury Cougar or Ford Mustang equipped with a manual transmission. Replaces Ford part # D1ZZ-2A487-B.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with an automatic transmission and drum brakes. This is a short style pedal is for cars with four wheel manual drum brakes and is shipped bare.Ford part # D1ZZ-2455-C.

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with a manual transmission and drum brakes. This unique pedal that works with the wider collapsible 1968 steering column and with a clutch pedal. Shorter arm than power brake pedals. The picture may show hardware and pedal pad with trim, but the pedal is shipped bare.Ford part # C8ZZ-2455-E.

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with a manual transmission and drum brakes. This unit is for use with a clutch pedal and has a shorter arm than power brake pedals. The brake pedal is shipped bare. Fits any 1969-70 Mercury Cougar or Ford Mustang.Ford part # C9ZZ-2455-B.

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with a manual transmission and manual drum brakes.This unit features a shorter arm than power brake pedals and is for use with a clutch pedal. The picture may show hardware and pedal pad with trim, but the pedal is shipped bare.Ford part # D1ZZ-2455-D.

Used brake pedal for the Mercury cougar equipped with power brakes and a manual transmission. This is for use with the non-collapsible 1967 steering column and with a clutch pedal. Longer arm than manual brake pedals. Keep in mind automatic pedals can be trimmed down to work as manual transmission pedals. Pedal shipped bare, picture may show hardware and pedal pad with trim.*NOTE* You will have to drill holes in your existing manual brake pedal hanger to accomomdate the power brake pedal....

For use with a clutch pedal. Longer arm than drum brake pedals. Pedal shipped bare, picture may show hardware and pedal pad with trim. 1971-73 Mercury Cougar or Ford Mustang with 3 or 4 speed manual transmission and disc brakes.Replaces Ford part number D1ZZ-2455-A.

Reproduction driver side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability, the...

Reproduction driver side drum brake spindle. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Good used driver side (left hand) brake spindle for the Mercury Cougar or Ford Mustang equipped with front drum brakes. Our spindles shipped bare, without any hardware. We inspect every piece for spun bearings and any galling to the spindle shaft. These are getting hard to find because after market disc brake conversions require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Ford part # D0OA-3108-F.

Used driver side drum brake spindle for 1971-73 Mercury Cougar and Ford Mustang, as well as those mid sized Ford and Mercury's. Ford casting number D1OA-3108-AA.

Reproduction pair of drum brake spindles. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Reproduction passenger side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability,...