Dynacorn International

Exact Mustang reproduction with Ford logo and marking as original. Very correct reproduction right down to the Ford logo! Replaces Ford part # D1ZZ-15201-RRIn order for you to install with the 1971-73 Cougar installed metal frames, you will need to remove the locating pin on your D1AB-15A466-B window bracket with a Dremel or similar. Original Cougar red lenses had a part number of D1WB-15A464-RH.

Reproduction reverse (back up) light lens set for the Mercury Cougar. These reproductions do not have the Ford insignia, and are therefore cheaper than the other versions on the market. Fit and finish is very good. This set includes the driver side / left hand lens and the passenger side / right hand lens, with correct grey gaskets. Replaces Ford part # C9WY-15514-B (driver side / left hand lens), C9WY-15514-A (passenger side / right hand lens), and C9WY-15510 (gasket...

Reproduction driver side (left hand) rear apron extension for Mercury Cougar and Ford Mustang.

Reproduction passenger side (right hand) rear apron extension for Mercury Cougar and Ford Mustang.

Reproduction cowl center panel for Mercury Cougar and Ford Mustang.

Get ready for some serious labor if your car needs this complete panel!

Reproduction driver side front inner apron for both the Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Reproduction driver side rear inner apron for both the Mercury Cougar and Ford Mustang.

Reproduction passenger side front fender apron that has the shelf for installing the battery tray. *Restoration Hint* This section of metal was VIN stamped, consider welding in the stamped VIN section to keep your car whole.Here's a little film to help you fortify your flexxy feline!

Reproduction passenger side rear apron for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

If you buy this reproduction tower, you will no doubt save you time in clean up. But nothing will ever fit and look like original FoMoCo towers!Here's a little film to help you fortify your flexxy feline!

We highly suggest you look at our mint condition used towers for about the same price. Why mess around with repo when you can get FoMoCo?!Here's a little film to help you fortify your flexxy feline!

A nice reproduction. Bright zinc finish. Ford type connectors for quick installation. Not totally correct this one has a black plug with two different sized male connectors. Changing the bulb shroud allows this to be used with consoles. Originals had a blue plug. We also sell used 1967 pigtails. Bulb not included, get it here. Replaces Ford Part # C8ZZ-15A808-A Check out our video on rebuilding your shifter below: ...

New manufactured fuel / gas tank for 1967-68 Mercury Cougar and 1965-68 Ford Mustang, 16 gallon capacity, has drain plug. This is the economy version, which has a slightly different stamping, and is made in Taiwan. Replaces Ford part #C5ZZ-9002. Check out our video on replacing the fuel system on a '68 Cougar! ...

New manufactured fuel / gas tank for 1969 Mercury Cougar and 1969 Ford Mustang, 20 gallon capacity, has drain plug. This is the economy version, which has a slightly different stamping, and is made in Taiwan.Replaces Ford part #C9ZZ-9002. *NOTE* Tank will fit into all 1967-68 cars, fuel filler necks must be adjusted to fit with this taller tank. Sending units ideally should be changed to the 1969 sending units. 1970 cars with California emissions will have to change filler necks entirely. ...

New manufactured fuel / gas tank for 1970 Mercury Cougar and 1970 Ford Mustang, 22 gallon capacity, with drain plug. This is the economy version, which has a slightly different stamping, and is made in Taiwan. Replaces Ford part #D0ZZ-9002-D. *NOTE* Tank will fit into all 1967-69 cars, fuel filler necks must be adjusted to fit with this taller tank. Sending units ideally should be changed to the 1970 sending units for 22 gallons. 1970 cars with California emissions will have to change filler...

Reproduction fuel tank for the 71 - 73 Mercury Cougar. 20 gallon capacity, correct in every way. Beware that the Mustang tanks sold by most vendors has a different filler neck angle that doesn't fit Cougars. Replaces Ford part #: D1WY-9002-A ...

New manufactured stainless steel fuel / gas tank for 1969 Mercury Cougar and 1969 Ford Mustang, 20 gallon capacity, has drain plug. Replaces Ford part #C9ZZ-9002. *NOTE* Tank will fit into all 1967-68 cars, fuel filler necks must be adjusted to fit with this taller tank. Sending units ideally should be changed to the 1969 sending units. 1970 cars with California emissions will have to change filler necks entirely.

New manufactured stainless steel fuel / gas tank for 1970 Mercury Cougar and 1970 Ford Mustang, 22 gallon capacity, with drain plug. Replaces Ford part #D0ZZ-9002-D. *NOTE* Tank will fit into all 1967-69 cars, fuel filler necks must be adjusted to fit with this taller tank. Sending units ideally should be changed to the 1970 sending units for 22 gallons. 1970 cars with California emissions will have to change filler necks entirely. ...

Complete seat frame for the 1969 Eliminator or Mach 1 and all models in 1970. We highly recommend good used as they are more correct and significantly less expensive. These are drop shipped directly from the manufacturer. Passenger side shown.

Complete seat frame for the 1969 Eliminator or Mach 1 and all models in 1970. We highly recommend good used as they are more correct and significantly less expensive. These are dropshipped directly from the manufacturer. Passenger side shown.

Nice thick foam. Chromed mounting post. Includes base plate for seat. Keep in mind we have good used for less money, several colors available in good condition. Find them here.

We found that the plastic adjustment clip can break easily on these reproductions, so consider buying a good used original Ford part instead, for around the same price. Find it here.

Unlike the originals, the housing on this unit is hard plastic, not vinyl. The day / night function does not work well on this Chinese unit. Since we tell you up front that this is a substandard part that you will not be happy with, we will not accept returns. Keep in mind this is the EXACT mirror marketed by other vendors as "Good Quality". When you see this icon on a product, it means it's a sub-par item that we don't recommend, due to our own experience in handling and using this item on...