Dynacorn International

Reproduction ignition switch for the 1973 Cougar.  This version has a longer pigtail, and has a shield or tube covering the wires. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Original Ford part number was likely D3AZ-11572-A. Application also for 1971 Lincoln MK III and 1971 Ford Thunderbird. Ford had a service replacement ignition switch with a part number...

Reproduction passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...

Reproduction driver side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...

Economy reproduction aluminum rear deck lid moulding / trim for the 1967 - 1968 Mercury Cougar (will also fit on 1969-1970). This reproduction is as close to the original as possible, except for the fact that the clips included have 8mm nuts, unlike the originals. There is however one small problem, the metal on these mouldings is much softer than the originals and you have to take extra care when installing the clips, if you apply too much pressure when installing, you will dimple the...

Reproduction stainless steel scuff / sill plate. Fits Coupe or convertible, left or right. Sold as a pair. Ford emblem sold separate, find it here. Replaces Ford part # D1ZZ-6513298-A

Fits both left or right, sold individually. These have a higher degree of luster than the originals but are made of same material and weigh exactly the same as our NOS examples. Very little difference from our more expensive version which is made using original tooling. Ford Logo sold separate, sold individually, two required per car. Replaces Ford part # C5ZZ-6513208-B or C5ZZ-6513208-D.

This is the assembly that your inside door handle attaches to and features all new components. They are gold cadmium plated to resist rust and corrosion. *NOTE* We have had complaints of these not fitting as well as originals, therefore we suggest buying our used units. Rod retainers not included. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Steel stamped complete latch. See hardware for clips.

Steel stamped complete door latch assembly that goes inside your passenger side door and catches on the door striker assembly. See hardware for clips. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Finally an affordable reproduction is available. Steel stamped complete door latch assembly that goes inside your passenger side door and catches on the door striker assembly. See hardware for clips. Replaces Ford Part # : C9AZ-6221812-A

Steel stamped complete latch. See hardware for clips. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

This is the assembly that your inside door handle attaches to and features all new components. They are gold cadmium plated to resist rust and corrosion. *NOTE* We have had complaints of these not fitting as well as originals therefore we suggest buying our used units. Rod retainers not included. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Reproduction passenger side (right hand) vent window frame for the Mercury Cougar or Ford Mustang. This premium reproduction is a much better fit than the economy overseas version.  Check out our video below for helpful tips on disassembling your vent and quarter windows: ...

Reproduction driver side (left hand) vent window frame for the Mercury Cougar or Ford Mustang. This premium reproduction is a much better fit than the economy overseas version. Check out our video below for helpful tips on disassembling your vent and quarter windows: ...

New Supplier Now Available! *Unlike our other sill plates, these are sold as a pair* Ford never made these in stainless but what a great upgrade! The advantage we see with these is that they do not dent or scratch as easy when you release your seat belt. They also can be polished easily (unlike anodized aluminum). These weigh 1.5 pounds each, triple of what the originals weigh. Sold as a pair only. *NOTE* There are two suppliers on these and we now carry only the Dynacorn...

These are the same left to right, convertible or coupe. These appear to be made from the same thickness of aluminum as original and weigh .44 pounds as opposed to .50 for the originals but the aluminum used is not nearly the quality of originals. You can literally mutilate these parts with your fingers as you would an aluminum can. We recommend the premium quality sills. These are a poor reproduction that will not hold up well over time, we cannot recommend this part. We HIGHLY recommend...

Good quality but not as good as original in that it is too shiny. Fits Coupe or convertible, left or right. Sold individually. Ford emblem sold separate. Replaces Ford part # D1ZZ-6513298-A

These are correct for XR7 or standard 1967 models. Used handles are almost always pitted due to lack of use. These are different than the front in that they are held on with an Allen set screw and are shorter in length. Replaces Ford Part #: C5ZZ-6530322-A. *NOTE* We have no good used examples of these rear window cranks as they are very prone to pitting over the years.

High quality reproduction. Fits as good as it looks! You can click this image for a magnified view. Replaces Ford Part # C7ZZ-6522600-A or C5ZZ-6522600-C.

Set of 4 reproduction wheel lip mouldings for the 69-70 Cougar. These are spot on and we had no problem fitting them on our cars, the only difference we noticed is that the aluminum is softer than the originals and prone to dimpling. And since they're reproductions, no cores are required! Keep in mind that when you remove your rear core mouldings, you can send them to us as they might be eligible for in store credit. For more info on aluminum trim restoration & core exchanging, check out our...

Reproduction set of 4 rear window mouldings / trim for the 69 - 70 Mercury Cougar. No core required, but keep in mind that we will give store credit for your original restorable trim!

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications (drilling extra holes, will not lineup with factory holes) they can be made to fit your 1971 - 1973 Mercury Cougar.

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications they can be made to fit your 1971 - 1973 Mercury Cougar.

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications (drilling extra holes) they can be made to fit your 1971 - 1973 Mercury Cougar.