Holley / Scott Drake

Reproduction rebuild kit for your 1967-70 Cougar or Mustang steering box only with the 1-1/8 inch sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a budget, you can rebuild your box with this kit. SMB-K, SMB-D, and SMB-F tagged steering boxes. Probably a DIY youtube video out there for...

Reproduction D0ZZ-3304-A Manual steering drag link for all 1970 Cougar and Mustang and 1969 Boss 302 Cougar Eliminator & Boss2 Mustang with a non-power assist manual steering system. This is the same as 1969 manual steering drag link, but with larger holes for 1970 ball joints. Meaning more heavy duty, Boss2 specifications if you will. *Note - if installing on a 1969 Mercury Cougar or Ford Mustang, you will need to use 1970 inner tie rod ends. 

Replaces Ford part # C7AZ-3A006-C or D1VY-3A006-A.

Replaces Ford part # C7AZ-3A006-C of D1VY-3A006-A.

Premium grade of idler arm. Fits all 1967-70 Mercury Cougar and Ford Mustang. If you have loose / sloppy steering, replacing this part could help tighten things up. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Drag link hole size: 5/8" Customer feedback: Hey, just wanted to thank you for your prompt service. Last Friday...

Sold individually, right is the same as left.  NOTE* You can use the 1968 - 1973 lower control arms on a 1967 ONLY if you change the strut rods to the 1968 - 1970 style. We have the strut rods available in both new and used form. Find them here. Replaces Ford part # C8OZ-3078-A. Having issues with wobbly or loose steering? Check out our video on sloppy steering below.  ...

Sold individually, two required per car. These are brand new, not rebuilds. Please click onto the listing of our NOS arms to see side by side comparison pictures. We do not have the 4 bolt upper ball joint version available at this time. Replaces Ford part # C7DZ-3082-A. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Features quality stamped steel construction, bushings, nuts, anti-squeak coil protector pads. From the get go these were never a very good design... The rubber is prone to cracking and the unit will bind under severe use. Not just speaking of the unit we are offering but all of them including the original Ford units. Here is an interesting article for those that are not happy with status quo. Global West and others have come up with their own solutions and after we have spent more time testing...

These are equal in performance to other name brand high pressure gas shocks at a significant lower price. These shocks are best suited for drivers looking for firm ride with a solid controlled “feel of the road”. These units are sold individually.

High Performance Coil Spring Perches offer a very affordable upgrade to stock spring perches with rubber bushings. These are made with synthetic elastomer bushings which are similar to polyurethane in performance and longevity, but will not squeak like polyurethane. The perch can rotate 360 degrees on the shaft, which allows the front suspension to articulate freely. This feature also eases the installation of the coil spring. Zerk grease fittings are installed and locking nuts are included....

This is the reproduction exclusive to the 1967 Mustang. Will also work on Fairlane, Comet, Futura and Falcon. C7OZ-3078.  NOTE: Will not work on the 1967 Cougar without the use of 1967 Mustang strut rods.  Get your control arms for 1968 - 1973 here.

Designed as a direct-fit OE-style replacement, this modulator valve will fit directly into the factory location of your current Cougar or Mustang valve. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs.

Fits all applications for both automatic and manual transmissions, big block and small block. Will also work with your Tremac / T-5. Replaces Ford part # C4DZ-6068-A.

Inner tie rod end for 1971 - 1973 Mercury Cougar and Ford Mustang with or without power steering and either drum or power disc brakes. Quality reproduction part. Sold individually, two needed per car. Replaces Ford Part #: D1ZZ-3A131-A

Outer tie rod end for 1970 – 1973 Mercury Cougar and Ford Mustang with either power steering or manual steering and with drum or disk brakes. Quality reproduction part. Includes 1969 Boss 302 Eliminator and Mustang, and 1970-74 Ford Maverick and Mercury Comet. Sold individually, two needed per car. Made in the USA. Replaces Ford Part #: D0OZ-3A130-B.

After being obsolete for years we have brought back another hard to find clutch equalizer component for 1971-3 Mustang and Cougar. Numerous other Ford application too. Replaces Ford part # C5AZ-7B545-A

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard! Only the 71-73 came with the speckled pattern.

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

Correct spare tire hold down wing nut for the 1967 Mercury Cougar or Ford Mustang. Replaces Ford Part #: B9AZ-1462-A.

Exact copy of bolt used by Ford. Zinc plated. Fits the 1967 Mercury Cougar or Ford Mustang. Check out the very first Cougar in our video below!

4" mounting Plate for Standard Spare Tire. Replaces Ford Part #: C5ZZ-1424-A.

3 1/8" Style Steel Wheel Spare Tire Hold Down. Available in Black or Chrome. Ford Master Parts Catalog indicates that this hold down was found on some 68 and 69 Cougars with SS Wheels. You may need to bend the ears in slightly to get them to fit properly inside the hole in the center of the wheel. Replaces Ford Part #: C8MY-1424-A.

3 1/8" Style Steel Wheel Spare Tire Hold Down. Available in Black or Chrome. Ford Master Parts Catalog indicates that this hold down was found on some 68 and 69 Cougars with SS Wheels. You may need to bend the ears in slightly to get them to fit properly inside the hole in the center of the wheel. Replaces Ford Part #: C8MY-1424-A.

Spare Tire Mount Wing Nut Reproduction for the 1968 through 1973 Mercury Cougar / Ford Mustang